Whilst testing Hasivo s1100wp-8gt-se LED configuration, several error
messages were presented which didn't indicate which led_set they were
referencing, nor what the value was that caused the invalid configuration.
Migrate to use dev_ print messages for this function.
And tidy up both when the error message is reported (don't show it when
an led_set isn't in the DTS) and what details the message presents.
Signed-off-by: Bevan Weiss <bevan.weiss@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19791
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add defines for RTL930x and RTL931x led_set 'modes' (to avoid magic numbers
in dts files).
Signed-off-by: Bevan Weiss <bevan.weiss@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19791
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove old kernel support to prepare for the next LTS release.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19821
Signed-off-by: Nick Hainke <vincent@systemli.org>
We have not received any negative feedback in the past three months.
It's time to switch the default kernel to 6.12.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19821
Signed-off-by: Nick Hainke <vincent@systemli.org>
All of this uses OF now. No need to keep platform data around.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19804
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit repeats the mdio function relocation from the other targets.
In short that means:
- phy read/write functions are moved away from the phy driver
- SerDes read/write functions are moved away from the dsa driver
- All gets consolidated into the mdio driver (inside the ethernet driver)
This is mostly a copy/paste to keep the changes small. The SerDes phy mapping
and the simplification of the central bus functions will come later.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19743
Signed-off-by: Robert Marko <robimarko@gmail.com>
The IPQ4019 datasheet indicates that the maximum supported SPI
frequency is 25 MHz. My experiment on SKSpruce WIA3300-20 shows
that exceeding this threshold can lead to instability of SPI
peripheral. Limit the SPI clock frequency to the QSDK recommended
value 24MHz to enhance stability.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19744
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now devicetrees imported from Linux kernel release are used, so update
DEVICE_TREE to use correct path. A patch was backported to increase
SYS_MALLOC_F_LEN for stm32mp13 (more alloc space is needed due to SCMI
update to protocol v2.0).
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/19779
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The support is done. Let's set 6.12 as testing kernel.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19152
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Support in mt76 has existed for quite a while. Use it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19771
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that the driver has been enhanced for RTL931x devices and
the DTS is up to date, activate the needed kernel configuration
for the two RTL931x subtargets.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19776
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The RTL8231 auxiliary controller is not defined in the rtl931x.dtsi.
Additionally the pinmux is configured at the wrong address. Fix
this.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19776
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The auxiliary RTL8231 controller driver is missing RTL931x support.
Add it by defining the proper register and matching compatible.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19776
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Realtek DTS's use several macros for convenient phy/port definition.
These are repeated for the RTL83xx targets and most are missing for the
RTL93xx targets. In the near future we want to add high port count
switches with 1GBit Ethernet for them too. As a preparation provide a
central include so the definition is only needed once and is available
for all targets.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19772
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since 6.12 is now default, drop 6.6 support.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19778
Signed-off-by: Nick Hainke <vincent@systemli.org>
Let's switch the ipq40xx target to use kernel 6.12 by default.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19778
Signed-off-by: Nick Hainke <vincent@systemli.org>
3d953628bf17 udebugd: add support for setting an override config
93f6df0240e5 udebug-cli: add support for overriding config on the command line
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support for the Texas Instruments BQ32000 I2C real-time clock chip.
Tested on a custom board based on Hi-Link HLK-7628N.
Signed-off-by: Ondrej Kolar <ondrej@kolarovo.cz>
Link: https://github.com/openwrt/openwrt/pull/19764
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Initialize data to {} if null before calling mac80211.sh
to avoid a confusing error message in the syslog.
Fixes: https://github.com/openwrt/openwrt/issues/14010
Signed-off-by: Tobias Waldvogel <tobias.waldvogel@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cosmetic change]
f3fc0b760406 libuci: fix false positive warning on older gcc versions
9033e8c27253 blob: use blobmsg_parse_attr in __uci_blob_check_equal
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The option iface should be optional according to the description
of /etc/config/wireless in order to avoid repeating the definition
for each virtual interface.
Signed-off-by: Tobias Waldvogel <tobias.waldvogel@gmail.com>
We are using upstream otto timer. Delete some downstream leftovers.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19769
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop our downstream driver in favor of an upstream existing driver which
is available starting from v6.13.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19736
Signed-off-by: Robert Marko <robimarko@gmail.com>
Adapt the device tree definitions of rtl93xx devices and the base dtsi
for rtl930x and rtl931x to match with what's expected by the recently
backported RTL9300 I2C driver.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19736
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport/add all patches for the upstream RTL9300 I2C driver.
The upstream driver was added in 6.13 and was heavily based on our
downstream driver except for how the multiplexing behaviour is handled.
This driver was working fine with basic SFP operation on RTL930x devices
but there was no support for RTL931x though.
Major advantage over our downstream driver is: The multiplexing
behaviour is handled completely by the driver. Thus, there's no need for
a separate rtl9300-mux driver as we had it downstream. Moreover, this
simplifies the DTS of affected devices a lot since we can now move the
controller definition - which is in the DTS of each device so far - to
the base DTSI.
Currently pending patches are also included because the progress on
getting this upstream seems really slow right now, albeit upstream
maintainers may require several changes to the current state.
These include:
- patches fixing several issues in the driver
- patches doing a refactoring of the driver and adding support for RTL931x
See the commit messages included in each patch to have details on the
changes.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19736
Signed-off-by: Robert Marko <robimarko@gmail.com>
