Mediatek/mt7623 currently uses the PREEMPT model, which is not aligned with
OpenWrt's default. Switch to PREEMPT_NONE for consistency with OpenWrt's
default configuration. Preemption model selection is now available via
menuconfig for further customization.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/21413
[Added some config options again]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The indicator is unused by default and not associated
with the wan port. So let’s fix this.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21635
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a cosmetic change. There is no need to use mac
address increment/decrement in the dts on these devices,
so this can be simplified.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21635
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In the original DTS from the device firmware, there are
no entries that enable SPI calibration. Therefore, it
should be disabled.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21635
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Keenetic devices always use the WAN port MAC address as
the MAC address printed on the label.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21635
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This default pinctrl doesn't work at all. We must add pinctrl phandle
to the ethernet-phy node or mac node. This patch removed the internal
phy LED pinctrl group definitions from the SOC dtsi because it is
currently only used by one device. Some incorrect LED pinctrls also
have been removed because these devices do not have hardware phy LED.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21108
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The PCIe NIC WED offload features depend on it. Also add the missing
"syscon" compatible for the wed_pcie node as it's accessed by
syscon_regmap_lookup_by_phandle().
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21108
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These stuffs were copied from the vendor SDK. There are currently
no drivers compatible with them. The pending upstream patches did
not include them either.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21108
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This reverts commit 7390e63374.
This broke SFP handling on some Mediatek SoCs.
Some SFPs are configured for inband/2500base-x link mode and were
rejected with this change.
Fixes: https://github.com/openwrt/openwrt/issues/21436
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport a bunch of upstream commits simplifying the RealTek PHY driver
and re-unifying the C22 and C45 driver instances.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The gmac definition has an offset of 1 compared to the label MAC.
Fixes: a55ab9e134 ("mediatek: filogic: prevent faulty mac address assignment")
Signed-off-by: Maximilian Baumgartner <aufhaxer@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/21560
Signed-off-by: Robert Marko <robimarko@gmail.com>
This adds support for the Airpi AP3000M 5G CPE based on MediaTek MT7981B.
Specifications:
SoC: MediaTek MT7981B (dual-core ARM Cortex-A53)
RAM: 1GB DDR4
Storage: 8GB or 16GB eMMC
Ethernet: 1x 2.5GbE LAN, 1x 1GbE WAN
Wireless: 2.4GHz/5GHz 802.11ax
Buttons: Reset, WPS
LEDs: System, 2.4GHz WiFi, 5GHz WiFi
Cooling: PWM-controlled fan
Expansion: M.2 slot for 5G modem
The factory partition (mmcblk0p2) is empty in stock firmware.
Execute via SSH before flashing OpenWrt:
```
dd if=/lib/firmware/MT7981_iPAiLNA_EEPROM.bin of=/dev/mmcblk0p2 bs=4k count=1
MAC addresses
```
Fixed MAC addresses are derived by macaddr_generate_from_mmc_cid.
Installation via U-Boot web page
Set static IP 192.168.88.2/255.255.255.0 on your computer.
Connect to the 1GbE port (WAN) and hold the reset button while booting the device. Wait for about 6 seconds, and release the reset button.
Open U-boot web page on your browser at http://192.168.88.1
Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
Wait for automatic reboot.
Installation via sysupgrade
Flash the sysupgrade file via LuCI upgrade page without saving the settings.
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21397
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Newer Cudy WR3000H units have a Motorcomm YT8821 PHY instead of a
Realtek PHY on the WAN port. Before this commit, the Motorcomm PHY
could not be autodetected by the kernel -- the PHY would show up as
just a generic clause 45 PHY and the proper driver would not be loaded.
The cause of the detection failure likely was that the YT8821 PHY was
held in reset during PHY detection. To fix this, move the reset GPIO
definition to the MDIO bus level. This reset line is deasserted before
the autodetection process, see also [1]. With this change, both Realtek
and Motorcomm PHYs can be supported with a single device tree.
[1]: https://lore.kernel.org/all/20251119134750.394655-1-horatiu.vultur@microchip.com/
Signed-off-by: Jakub Vaněk <linuxtardis@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21399
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Recent Cudy WR3000H v1 units have a Motorcomm YT8821 2.5G PHY for
the WAN interface instead of the RTL8221B PHY used in earlier units,
so add kmod-phy-motorcomm to be able to use it.
Signed-off-by: Andrew MacIntyre <andymac@pcug.org.au>
[linuxtardis@gmail.com: slightly reworded the commit description]
Signed-off-by: Jakub Vaněk <linuxtardis@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21399
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Commit ab805ec316 ("generic: add missing squashfs config") enabled
CONFIG_SQUASHFS_DECOMP_MULTI_PERCPU in the generic config, so it is no
longer needed in the target configs.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Link: https://github.com/openwrt/openwrt/pull/21465
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace downstream hack disabling SGMII in-band AN on the MediaTek platform
with pending upstream patch announcing in-band AN capabilities and implementing
configuring in-band AN in the PHY driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The patch that adds MT7987 support to the mtk-2p5ge
driver does the following:
case MTK_2P5GPHY_ID_MT7987:
phy_clear_bits_mmd MTK_PHY_LED_ON_POLARITY
case MTK_2P5GPHY_ID_MT7988:
phy_set_bits_mmd.. MTK_PHY_LED_ON_POLARITY
phy_set_bits_mmd... MTK_PHY_LED_ON_POLARITY | xxx
This clearly resulted in the LED polarity of the 2.5G PHY
on the MT7987 being reversed. Remove redundant MMD operations
to fix the 2.5G PHY LED error on Bananapi BPi-R4 Lite.
Fixes: d62fc50f ("mediatek: import patches from SDK to support MT7987 Ethernet")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
This patch fixes a bug in a patch we backported.
This patch was cherry picked from upstream Linux because it references a
patch we backported in the fixes tag.
The function phy_id_compare_vendor() is needed by the fix.
Refresh 782-05-v6.16-net-phy-Add-support-for-Aeonsemi-AS21xxx-PHYs.patch with the upstream code.
Fixes: 08a616b216 ("generic: backport support for Aeonsemi AS21xxx PHY")
Link: https://github.com/openwrt/openwrt/pull/21366
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes a bug in a patch we backported.
This patch was cherry picked from upstream Linux because it references a
patch we backported in the fixes tag.
Fixes: 813ecda1f3 ("generic: backport phylink patches for PCS/PHY caps OPs")
Link: https://github.com/openwrt/openwrt/pull/21366
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Replace pending patches which are already integrated in upstream Linux
with their upstream versions.
These patches were exported with:
git format-patch -1 -k
Link: https://github.com/openwrt/openwrt/pull/21366
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- adopted MTD partition size increase from 64M to 128M
-> this allows boot to complete
- moved MAC addressing stuff out of partition definitions
- all MAC addressing stuff is in .dtsi
Specifications:
SoC: MediaTek MT7981B
RAM: 256MiB
Flash: Winbond SPI-NAND 128 MiB
Switch: 1 WAN, 3 LAN (Gigabit) MediaTek MT7531
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7981B 2.4Ghz & 5.8Ghz
Led Layout from bottom to top:
Power
Mesh (RGB Led, user controllable, default set to OpenWrt Status)
WLAN 2 GHz (user controllable)
WAN (user controllable)
LAN3
LAN2
LAN1
WLAN 5 GHz (Not on front panel but blinks through enclosure,
user controllable)
Buttons:
Reset
Mesh (user controllable, no default function)
Installation:
A. Through U-Boot menu:
- Prepare your connecting computer to use a static IP in
network 192.168.1.0/24
- Power down the router and hold in the Reset button.
- While holding in the button power up the router again.
- Hold the button in for 10 seconds and then release.
- Use your browser to go to 192.168.1.1
- If you see a GUI allowing for flashing firmware then
you got the right model.
- Upload the sysupgrade file.
Note: Recovery GUI can be used to recover from an incorrect
firmware flash.
B. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled
(modified by the seller), you can easily upgrade
by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware,
then flash the firmware
MAC Addresses were found in Factory partition:
offset 0x4 F8:5E:3C:xx:xx:aa --> Router Label -2
offset 0xa F8:5E:3C:xx:xx:bb --> Router Label -1
offset 0x24 F8:5E:3C:xx:xx:cc --> Router Label +1
offset 0x2a F8:5E:3C:xx:xx:yy --> printed on Router Label
Signed-off-by: Jörg Seitz <github.joeterminal@xoxy.net>
Link: https://github.com/openwrt/openwrt/pull/19823
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- Use .dtsi for old z8103ax featuring a 64M Nand
- Prepare .dtsi for model C of z8103ax featuring a 128M Nand
This .dtsi is supposed to match boards labeled as hardware
revision Z8103AX_V01. Model variant D of zbt-z8103ax appears
to use very same board.
DTS include does also
- set wifi mac addresses in &wifi section
- set eth mac addresses in ð section
- set LAN switch mac addresses in &switch section
All of the above allows to get rid of 11_fix_wifi_mac script
Signed-off-by: Jörg Seitz <github.joeterminal@xoxy.net>
Link: https://github.com/openwrt/openwrt/pull/19823
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for the Cudy AP3000 Wall v1.
SoC: MediaTek MT7981b
RAM: 256MiB
Flash: spi-nand spi0.0: 128 MiB
Wifi: MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
LEDs: 1 LED in two colors (red & white)
Buttons: 1 reset, 1 led on/off
Ethernet: 5x 1GbE
Power: PoE powered (standalone)
The stock firmware is a customized variant of OpenWrt, which implements
a signature check that only allows flashing official firmware. Cudy offers
intermediate OpenWrt firmware images on their website [1][2] which do not
implement the signature check. After flashing the intermediate image the
upstream official OpenWrt image can be installed.
The stock firmware can be recovered via TFTP using the U-Boot based boot
loader[3]. Set up a TFTP server on your computer with IP 192.168.1.88/24
serving the stock firmware from Cudy's website renamed to "recovery.bin".
Press and hold the reset button while powering on the device, wait for the
TFTP server to send the recovery.bin file, then release the reset button.
The router will take a couple of minutes to reboot and set up the stock
firmware.
[1] https://www.cudy.com/blogs/faq/openwrt-software-download
[2] https://drive.google.com/drive/folders/1BKVarlwlNxf7uJUtRhuMGUqeCa5KpMnj
[3] https://www.cudy.com/en-us/blogs/faq/how-to-recovery-the-cudy-router-from-openwrt-firmware-to-cudy-official-firmware
Signed-off-by: Derek Denk <derek.denk@live.com>
Link: https://github.com/openwrt/openwrt/pull/21266
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The SUPPORTED_DEVICES sets for both Maxlinear (v1) and Airoha (v2)
devices were identical, so sysupgrade was unable to detect when an
incorrect image was being installed. This caused "soft bricking" of
devices when a v1 image was installed on a v2 device, and vice versa.
Fix this by making the supported_devices distinct for each device
version, by renaming the devices with a version-specific name.
This is reflected in the file name and the image metadata.
Fixes: https://github.com/openwrt/openwrt/issues/20566
Fixes: https://github.com/openwrt/asu/issues/1525
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20632
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This allows us to use the full size of nand,
which extends ubi size from 64Mb to 122.25Mb.
If you are at factory firmware, please refer
to [PR](https://github.com/openwrt/openwrt/pull/21141)
to boot into OpenWrt first.
1. Log in to the device and backup all the partitions,
especially unique `Factory` and `bdata` partitions
from System -> Backup / Flash Firmware -> Save mtdblock contents.
2. Install kmod-mtd-rw to unlock mtd partitions for writing:
```bash
apk update && apk add kmod-mtd-rw && insmod mtd-rw i_want_a_brick=1
```
3. Write new OpenWrt (U-Boot Layout) `BL2` and `FIP`:
```bash
mtd write openwrt-mediatek-filogic-cudy_wbr3000uax-v1-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cudy_wbr3000uax-v1-ubootmod-bl31-uboot.fip FIP
```
4. Set static IP on your PC: `192.168.1.254`, gateway `192.168.1.1`
5. Serve openwrt-mediatek-filogic-cudy_wbr3000uax-v1-ubootmod-initramfs-recovery.itb
using TFTP server.
6. Connect Router LAN with PC LAN.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt initramfs recovery has booted,
clean `/dev/mtd5` ubi partition to utilize maximum of free space & create ubootenvs:
```bash
ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
```
4. Perform sysupgrade.
Tested-by: 4pda users
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21225
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Another OEM variation of a Cudy WR3000 series device made for Russian market.
Hardware:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB GigaDevice SPI NAND. Flash Model: F50L1G41LB, ID: C801
- RAM: DDR3, 512 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- 1x WAN MT7531 (JXD 2531Z) 10/100/1000 Mbps
- 4x LAN 2x MT7530 (JXD 2529S) 10/100/1000 Mbps
- USB 3.0 port
- Buttons: Reset, WPS
- 8x LEDs: 2x Red, 6x Blue
- Serial console: no need to solder, just open the case and unskrew the radiator, TX-RX, RX-TX, GND-GND, VCC do not connect, 115200 8n1
- Power: 12 VDC, 1.5 A
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:AF:CA:xx:xx:x1 | label+1 |
| LAN | 80:AF:CA:xx:xx:x0 | label |
| WLAN 2g | 80:AF:CA:xx:xx:x0 | label |
| WLAN 5g | 82:AF:CA:xx:xx:x1 | label+1 |
+---------+-------------------+-----------+
Based on a factory layout with only 64mb partition for easier transition from factory to OpenWrt for users if the "intermediate" RSA signed firmware will be provided by Cudy.
**Installation**
The installation must be done via UART & TFTP by disassembling the router. On other occasions Cudy has distributed intermediate firmware and dts to make installation easier, but since this router is OEM special WB order for local RU market there is a possibility they will not provide it.
**Install using UART & TFTP**
1. Connect to UART.
2. Since the factory BL is locked and the boot process can not be stopped, you have to use mtkuartboot, hold reset, engage the power, boot into your payloaded bl2 & fip.
3. Connect to LAN and set your IP to 192.168.1.254.
4. Configure a TFTP server to serve openwrt-mediatek-filogic-cudy_wbr3000uax-v1-initramfs-kernel.bin file.
5. Run these steps in u-boot using the name of your file:
```
setenv bootfile openwrt-mediatek-filogic-cudy_wbr3000uax-v1-initramfs-kernel.bin
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.254
tftpboot
bootm
```
6. Router will boot into OpenWrt initramfs recovery, just open your browser `192.168.1.1` and sysupgrade with the `Keep settings` option turned off.
Tested-by: many 4pda users
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21225
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since there are many similar devices from Cudy (TR3000 / WR3000E / WR3000P / WR3000S / WBR3000UAX) this will allow to create OpenWrt U-Boot layout for all of them using same DDR3 target.
Tested-by: 4pda users
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21225
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware is identical to WRC-X3200GST3.
- SoC: MediaTek MT7622
- RAM: 512MB
- Flash: 128MB SPI-NAND
The -W suffix in the retail name (WRC-G01-W) denotes the casing color
and is omitted from the model name in the OpenWrt configuration to
maintain consistency with other Elecom devices.
Signed-off-by: Yuhei Amemiya <minihui@me.com>
Link: https://github.com/openwrt/openwrt/pull/21238
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Include XHCI USB drivers on the Cudy WR3000P v1 router, the drivers are
required to be able to use the USB port for USD devices.
Closes: https://github.com/openwrt/openwrt/issues/21231
Fixes: 04e9d154f2 ("mediatek: filogic: add support for Cudy WR3000P v1")
Signed-off-by: Dmitry Mostovoy <dmitry.mostovoy@ceifx.com>
Link: https://github.com/openwrt/openwrt/pull/21281
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove unused pinctrl groups defined in the device tree, probably as a
result of importing the vendor device tree which is based on the
reference board from MediaTek's SDK.
114b5c2063 ("mediatek: filogic: Add support ASUS RT-AX57M")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ASUS RT-AX57M, RT-AX54HP V2, RT-AX1800HP V2, RT-AX1800S V2, and RT-AX3000S all use the same firmware and have identical hardware
Hardware
--------
SOC: MediaTek MT7981b
RAM: 256MB DDR3L (Winbond W632GU6NB-09)
FLASH: 128MB SPI-NAND (Winbond W25N01KVZEIR)
WIFI: Mediatek MT7981b + Mediatek MT7976DAN 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531AE Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
MAC addresses
-------------
LAN Label MAC (stored in mtd ubi Factory partition at offset 0x4)
WAN LAN
2.4G LAN + 2 in first octet
5G LAN
Installation
-----------------------------------------------------------
Vendor-UI Method
-----------------------------------------------------------
1. Download the OpenWrt initramfs.trx image.
2. Connect the PC via LAN to one of the yellow router ports and wait
until your PC to get a DHCP lease.
3. Browse to http://192.168.1.1 (or whatever your router IP is configured as)
4. If your router is brand new, finish the setup process and log into
the Web-UI.
5. Navigate to Administration -> Firmware Upgrade and upload the
downloaded OpenWrt initramfs.trx image.
6. Wait for OpenWrt to boot. Open the default OpenWrt IP in a web browser and perform a system upgrade using the sysupgrade image as instructed in the top banner.
---------------------------------------------------------------------------
Revert to stock firmware:
1: Install package facinstall -> https://forum.openwrt.org/t/facinstall-package-for-easy-installation-factory-images/177587
2. Install Asus stock trx image via OpenWRT LuCI interface.
Signed-off-by: Garrett Mesmer <garrettmesm@gmail.com>
Co-authored-by: Oleg S <remittor@gmail.com>
Signed-off-by: Oleg S <remittor@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20491
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Popular cheap PWM fans for this machine, like the ones coming in
heatsink+fan combos will not work properly at the currently defined
medium speed. Trying different pwm setting using a command
echo $value > /sys/devices/platform/pwm-fan/hwmon/hwmon1/pwm1
I found:
pwm1 value fan rotation speed cpu temperature notes
-----------------------------------------------------------------
0 maximal 31.5 Celsius too noisy
40 optimal 35.2 Celsius no noise hearable
95 minimal
above 95 does not rotate 55.5 Celsius
-----------------------------------------------------------------
Current cooling levels are:
cooling-levels = <255 96 0>;
Thus only cpu-active-high and cpu-active-low modes are usable.
This patch fixes cpu-active-medium settings for bpi-r3 board.
This patch may not be enough. Users may wants to tweak their thermal_zone0
trip points, thus tuning fan rotation speed depending on cpu temperature.
That can be done on the base of the following example:
=== example =========
# cpu temperature below 25 Celsius degrees, no rotation
echo 25000 > /sys/class/thermal/thermal_zone0/trip_point_4_temp
# cpu temperature in [25..32] Celsius degrees, normal rotation speed
echo 32000 > /sys/class/thermal/thermal_zone0/trip_point_3_temp
# cpu temperature above 50 Celsius degrees, max rotation speed
echo 50000 > /sys/class/thermal/thermal_zone0/trip_point_2_temp
=====================
Changes v2:
* put patch to a proper directory
* updated patch description
* tested with latest openwrt based on linux-6.6
Changes v3:
* use upstream linux patch
* update patch description
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17130
Signed-off-by: Robert Marko <robimarko@gmail.com>
Usually we do not use MHz to describe the DDR transmission rate. In
fact, the clock frequency of the DDR3-1866 is only 933 MHz. MT/s is
a more commonly used unit.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
cudy ap3000-v1 did not work correctly in failsafe mode
because the address 192.168.1.1 was missing on the eth0 inteface.
it was reachable via it's IPv6 link-local address however.
this commit fixes the issue.
Fixes: https://github.com/openwrt/openwrt/issues/20750
Signed-off-by: Martin Nadvornik <martin.nadvornik@gmx.at>
Link: https://github.com/openwrt/openwrt/pull/21172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification:
SoC: MediaTek MT7981B
Flash: ESMT F50L1G41LB 128MB
RAM: ESMT M15T2G16128A DDR3 256MB
Ethernet: 3x 1G
Button: Reset, WPS
MAC addresses
LAN: Label MAC (stored in Factory partition offset 0x1fef20)
WAN: LAN + 1
WiFi: LAN
Official LED layout, from left to right:
[power] [internet] [wps] [wifi] [lan3/2/1] [wan]
Redefinition for OpenWrt:
[power]: used for led-boot, led-failsafe, and led-running
[internet]: used for WAN RX/TX indication
[wps]: used for led-upgrade
[wifi] and [lan3/2/1]: unchanged
[wan]: used for WAN link indication
Installing OpenWrt:
- Setup a tftp server on your PC. Copy
xxx-preloader.bin, xxx-bl31-uboot.fip and
xxx-initramfs.itb to tftp root directory.
- Connect to the router via ssh or telnet,
username: useradmin, password is the web
login password of the router.
- Backup all critical flash partitions with
the following commands where x.x.x.x is
the IP of your PC.
IP=x.x.x.x
cd /dev
for d in /sys/class/mtd/mtd?; do
if [ "$(cat $d/name)" = "BL2" ]; then
tftp -l $(basename $d) -r bl2.img -p $IP
elif [ "$(cat $d/name)" = "FIP" ]; then
tftp -l $(basename $d) -r fip.bin -p $IP
elif [ "$(cat $d/name)" = "Factory" ]; then
tftp -l $(basename $d) -r factory.bin -p $IP
fi
done
for d in /sys/devices/virtual/ubi/ubi0/ubi0_*; do
[ "$(cat $d/name)" != "customer" ] && continue
tftp -l $(basename $d) -r customer -p $IP
break
done
- Flash with the following commands:
cd /tmp
tftp -r xxx-preloader.bin -g x.x.x.x
tftp -r xxx-bl31-uboot.fip -g x.x.x.x
mtd write xxx-preloader.bin spi0.0
mtd write xxx-bl31-uboot.fip FIP
mtd erase ubi
- Set a static ip(192.168.1.254) for your PC.
And then reboot the router. It will run
initramfs image automatically.
- After openwrt boots up, perform sysupgrade
via web UI.
Reverting to the vendor firmware:
- Setup a tftp server on your PC with ip
address 192.168.1.254. And make sure
bl2.img, fip.bin, factory.bin and customer
are located in tftp root directory.
- Power off the router.
- Press and hold WPS key, then power on
the router.
- Release WPS key, when internet/wifi/wps
leds are blinking.
- Wait until internet/wifi/wps leds light
up, power off the router.
- Press and hold reset key, power up the
router, release reset key 15s later.
- Connect to http://192.168.1.1, now you
can upload vendor .bin firmware.
Uboot netconsole:
Uboot netconsole can be enabled by WPS
or reset key.
- Setup a linux PC with ip 192.168.1.254.
Open a new terminal and execute
'stty -isig -echo cbreak; nc -lup 6666'
- Press and hold WPS(or reset) key, then
power on the router.
- Release key once internet/wifi/wps leds
are all on.
NOTE: don't hold the key more than 5s
after internet/wifi/wps leds on, or it
will try to revert to vendor firmware.
- 5s later, uboot bootmenu will show on
the terminal.
Signed-off-by: Zhiwei Cao <bfdeh@126.com>
Link: https://github.com/openwrt/openwrt/pull/18631
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit replaces the 7-8 spaces with 1 tab to modify the indentation appropriately.
Signed-off-by: Brian Lee <larte332@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21018
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Kebidumei AX3000-U22 is one of many clones of the same range extender
that can be found on Aliexpress or other Chinese portals.
The easiest way to identify this model is by searching for "AX3000
Repeater" and picking the device that looks like mine [0].
Specification:
- SoC: MediaTek MT7981B (1.3 GHz)
- RAM: 256 MB
- Flash: 16 MB SPI NOR
- Ports: 1 x 1 GbE
- Antenna: 6 (2 fake)
- WiFi: MediaTek dual-band WiFi 6
- 2.4 GHz: b/g/n/ax, MIMO 2x2
- 5 GHz: a/n/ac/ax, MIMO 2x2
- Buttons: Reset & WPS
- LEDs: Ethernet (green), Status (red, green, blue)
- Power: 110–240 V AC (internal PSU, board uses 12 V DC)
- Serial: unmarked connector on PCB
[1: Vcc, 2: RX, 3: TX, 4: GND]
Install via OEM web UI:
1. Use reset button to perform factory reset.
2. Connect PC to LAN port and obtain DHCP address.
3. Upload the sysupgrade image via OEM firmware upgrade page,
e.g. http://192.168.18.1/upgrade.html
4. After reboot, hold reset button to clear leftover vendor config.
Install via serial:
1. Connect serial console (115200 8N1).
2. Enter the console.
3. Backup mtd4 partition if you want to restore OEM FW later.
4. Download image.
5. Run 'sysupgrade -n'.
Revert to stock:
1. Run sysupgrade without keeping config using mtd4 backup.
[0] https://openwrt.org/_media/media/kebidumei_ax3000-u22.png
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20287
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Keenetic KN-1812/Netcraze NC-1812
Device specification
--------------------
SoC Type: MediaTek MT7988D, Cortex-A73, 64-bit
RAM: 1024MB DDR4 Micron MT40A512M16TB-062E:R
Flash: SPI NAND Winbond W25N02KV (256 MiB)
Ethernet: 4x1GbE (internal MT7988 built-in) + 2.5GbE (internal MT7988 phy) + 10GbE (RTL8261BE)
WLAN: MT7992AV
WLAN 2g: MediaTek MT7975N, b/g/n/ax/be, MIMO 4x4
WLAN 5g: MediaTek MT7977B, a/n/ac/ax/be, MIMO 4x4
LEDs: 5 LEDs, 1 power green, 1 internet green,
2x fn green, 1 wlan green, gpio-controlled
Button: 4 (Reset, WPS, FN1, FN2)
USB port: Yes, 1xUSB3.2 and 1xUSB2.0 (via GL850G)
Power: 12 VDC, 3 A
Notes:
* The device supports dual boot mode
* Fn2 led reassigned to wlan 2.4
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. a) Keenetic
Rename "openwrt-mediatek-filogic-keenetic_kn-1812-squashfs-factory.bin"
to "KN-1812_recovery.bin" and place it in tftp server directory.
b) Netcraze
Rename "openwrt-mediatek-filogic-netcraze_nc-1812-squashfs-factory.bin"
to "NC-1812_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20737
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This AX3000 flying saucer-shaped device is sold under a few names:
- Widelantech WAP430X
http://www.widelantech.com/?m=home&c=View&a=index&aid=131
- Felicomm
- UeeVii UAP200 (sold on amazon.com)
True name, as marked on the PCB and as appears in the DTS, is WAP430X.
Hardware:
- SoC: Mediatek MT7981B
- RAM: 256MiB DDR3
- ROM: 16MiB NOR flash (Winbond 25Q128JVSQ)
- Wired: one GbE RJ45 port
- Wireless: Mediatek MT7976CN DBDC
- Antennas: Internal (two 2.4 GHz 4.5 dBi, three 5 GHz 6 dBi)
- GPIO: two blue LEDs (status, WLAN), one button (reset)
- Power: DC5521 (12V) or 802.3af PoE (48V 0.3A)
- UART: J500 on PCB [3v3] (Rx) (Tx) (Gnd), 115200n
Original firmware is GECOOS 8.0_2024081000, a fork of OpenWrt 21.02
created by Widelantech. All ports are closed except 443 (web management
interface) and 80 (redirects to 443). UART is locked down, but U-Boot
bootloader is friendly.
Installation is done via UART (see note below).
Method 1: press any key during boot to enter MTK U-Boot bootloader,
then choose option 2 (Upgrade firmware) and upload sysupgrade binary
via TFTP (or via Xmodem).
Method 2: put sysupgrade binary on a webserver (http, not https); after
GECOOS loads, choose option 4 (固件在线升级 = online firmware upgrade)
in the menu and enter the URL to the sysupgrade binary.
Note: GECOOS has a slick web management, and firmware can be uploaded
at https://6.6.6.6/#/system/sysupgrade but it's still not clear how to
convert the sysupgrade binary to a factory binary accepted by the web
interface (WIP).
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20402
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Unneeded semicolon
WARNING comparing pointer to 0
WARNING: NULL check before some freeing functions is not needed.
WARNING: casting value returned by memory allocation function to (u32 *)
ERROR: allocation function on line 378 returns NULL not ERR_PTR on failure
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19932
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
