The initramfs images beginning 24.10 do not boot on the AP3825i. The
space available for decompression preceeding the compressed image is not
enough, crashing the system.
To make existing installation instructions continue to work, link the
loader at an address following the loadaddress of the U-Boot image.
Signed-off-by: David Bauer <mail@david-bauer.net>
Teltonika RUTC50 has a 5G modem. Install uqmi by default to control the
modem with the default package set.
Signed-off-by: David Bauer <mail@david-bauer.net>
According to the TP-Link websites the Archer C50 v6 EU is the same model
as the Archer A5 v6 EU. Installation method is the same as the C50 v6, as
they are basically the same hardware.
The commit is based on e9ac1b1.
Signed-off-by: David Senoner <seda18@rolmail.net>
All kernel symbols are automatically refreshed by
`make kernel_oldconfig CONFIG_TARGET=target`.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Link: https://github.com/openwrt/openwrt/pull/18669
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Link: https://github.com/openwrt/openwrt/pull/18669
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Backport eMMC Command Queuing support for RK3576/RK3588.
As the RK3576 device-tree has been upstreamed with the 'supports-cqe;'
property set by default, the kernel already tried to use CQE, which
results in system hang during suspend. This fixes the issue.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20780
Signed-off-by: Robert Marko <robimarko@gmail.com>
Default behavior for apk was to create an uncompressed scripts.tar
file. Due to the structure of tar files, with fixed block
size and null padding, this file becomes very large on OpenWrt
installations where there are typically two scripts per package.
This could cause the raw tar file to easily grow to over 500KB,
whereas the compressed file is generally around 20-30KB.
When stored in the /rom partition of a squashfs device, the file
is compressed and this is not an issue. But, as soon as you add
or delete a package, the scripts.tar file is fully expanded into
the /overlay partition and can cause issues on small-flash devices.
This issue was addressed in an upstream commit by detecting
whether the scripts.tar file is compressed (its name must be
exactly 'scripts.tar.gz'), and then retaining that compression by
reading/writing the file using a compressed stream.
This commit applies a cherrypicked patch for the upstream commit, and
compresses the scripts.tar during construction of the device rootfs.
Fixes: https://github.com/openwrt/openwrt/issues/17108
Link: 012cdcfdf9
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20795
Signed-off-by: Robert Marko <robimarko@gmail.com>
The values provides are correct if after the @ it would be the bus
number and then device number. But it's actually, device and then
function for pcie devices.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19425
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fixes:
Warning (pci_bridge): /plb/pciex@d00000000: node name is not "pci" or "pcie"
Matches upstream commit: 86bc917d2ac117ec922dbf8ed92ca989bf333281
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19425
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Rework each affected mtdsplit driver to make use of -ENOENT error
instead of -ENODEV to handle new kernel that checks error from parser on
subpartitions.
The only acceptable error is -ENOENT that skip the parser. This follow
pattern used upstream and also by an mtdsplit parser, mtdsplit_bcm_wfi,
and also by a workaround currently implemented for mtdsplit_mstc_boot.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 627a0e7da0.
A better solution has been accepted upstream that doesn't hide all
unexpected error.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add new and remove obsolete symbols for Kernel 6.12 by running
make kernel_oldconfig.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/20167
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/20167
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport a trivial patch that half restore original functionality of MTD
parser for subpartition by ignoring if the parser returns -ENOENT.
This fix parsing and booting of some brcm devices.
Link: https://github.com/openwrt/openwrt/pull/20822
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add new and remove obsolete symbols for Kernel 6.12 by running
make kernel_oldconfig.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/20166
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/20166
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport the kernel parf of the WiFi MT76 offload patch. This is needed
as we have a dedicated package that only have mt76 related changes.
Add missing include in airoha_offload.h in order to enable MT76 NPU
offloading (and fix compilation error)
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
[ improve commit title/description and use proper patch ]
Link: https://github.com/openwrt/openwrt/pull/20807
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add new and remove obsolete symbols for Kernel 6.12 by running
make kernel_oldconfig.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/20169
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop upstreamed patches:
* 130-arm64-dts-broadcom-bcmbca-bcm4908-set-brcm-wp-not-co.patch
All other patches automatically refreshed.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/20169
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/20169
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19708
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
After investigating the EAP235-Wall u-boot GPL code, it was found that
the u-boot of this device directly loads the kernel from the SPI NOR
Flash direct access address. However, due to hardware limitation, MT7621
can only remap the first 4MiB Flash. Excluding some partitions before
the kernel, this device can only boot kernels smaller than 0x360000.
This means that unless you install a modified bootloader, the mainline
OpenWrt will no longer work on this model.
Closes: https://github.com/openwrt/openwrt/issues/20500
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20509
Signed-off-by: Robert Marko <robimarko@gmail.com>
EDUP EP-RT2960S has the similar hardware design as the SIMAX1800T.
The main difference is the arrangement of the GPIO pins
and the location of the MAC address.
Specification
-------------
- SoC : Mediatek MT7621
- RAM : 256 MiB DDR3
- Flash : 128 MiB NAND Flash
- WLAN : Mediatek MT7905 DBDC
- 2.4 GHz : 2x2 MIMO WiFi6
- 5 GHz : 2x2 MIMO WiFi6
- Ethernet : MT7621 built-in 10/100/1000 Mbps 1x WAN; 3x LAN
- UART : 3.3V, 115200n8
- Buttons : 1x RESET; 1x WPS/MESH
- LEDs : 1x Multi-Color(Blue;Green;Red)
- Power : DC 12V1A
- CMIIT ID : 2022AP7163
- TFTP IP :
- server : 192.168.1.254
- router : 192.168.1.28
TFTP Installation(recommend)
------------
1. Set local tftp server IP "192.168.1.254" and NetMask "255.255.255.0".
2. Rename initramfs-kernel.bin to "factory.bin" and put it in the root
directory of the tftp server. tftpd64 is a good choice for Windows.
3. Remove all Ethernet cables and WiFi connections from the PC, except
for the one connected to the EDUP EP-RT2960S. Start the TFTP server, plug
in the power adapter and wait for the OpenWrt system to boot.
4. Backup "firmware" partition and rename it to "firmware.bin". We need
it to back to the stock firmware.
5. Use "fw_printenv" command to list envs. If "firmware_select=2" is
observed then set u-boot env variable via command:
`fw_setenv firmware_select 1`
6. Apply sysupgrade.bin in OpenWrt LuCI.
Web UI Installation
------------
1. Apply update by uploading initramfs-factory.bin to the web UI.
2. Use "fw_printenv" command to list envs. If "firmware_select=2" is
observed then set u-boot env variable via command:
`fw_setenv firmware_select 1`
3. Apply squashfs-sysupgrade.bin in OpenWrt LuCI.
Return to Stock Firmware
----------------------------
Restore the backup firmware partition in the installation step 4.
MAC addresses
-------------
+---------+-------------------+
| | MAC example |
+---------+-------------------+
| LABEL | 24:D5:1C:xx:xx:xx |
| LAN | 24:D5:1C:xx:xx:xx |
| WAN | 24:D5:1C:xx:xx:xx |
| WLAN2G | 24:D5:1C:xx:xx:xx |
| WLAN5G | 26:D5:1C:xx:xx:xx |
+---------+-------------------+
Tips:
-----------
User can use `TFTP Installation` method to recover a brick device.
Signed-off-by: Andrii Kuiukoff <andros.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20600
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CLI tools hostapd_cli and wpa_cli are compiled with
`TARGET_LDFLAGS_C` rather than the standard `TARGET_LDFLAGS`.
This variable is empty, leading to global linker options not being
applied.
Set this variable equal to `TARGET_LDFLAGS` right after the package.mk
include to make sure global linker options are applied, but local options
such as linking to crypto libraries are not.
Signed-off-by: Matthias Van Parys <matthias.vanparys@softathome.com>
Link: https://github.com/openwrt/openwrt/pull/20345
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add TARGET_LDFLAGS to MYLDFLAGS make sure that the required flags are used
during the compilation.
Signed-off-by: Jonathan Luijsmans <jonathan.luijsmans_ext@softathome.com>
Link: https://github.com/openwrt/openwrt/pull/20642
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The functions iterating through the port statistic/counter (for
initialization or polling) use the generic name "i" for the iterator. This
makes reading the actual body of the loop cumbersome because it is not
clear that various parameters of functions are about a ports.
Suggested-by: Felix Baumann <felix.bau@gmx.de>
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20631
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
