This is useful if multiple passwords were specified without
the use of a SAE password identifier. This is the only
way to get multiple passwords for a single peer to work
without resorting to password identifiers.
Unfortunately, support for password identifiers is non-existent
on Android and macOS; and possibly others. So this is the only
option in that case.
As an alternative, one could also continue to use WPA2-PSK instead
as that could easily resort to a bruteforce approach without any
complications.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/20597
Signed-off-by: Robert Marko <robimarko@gmail.com>
As this is generally only useful with "proxy_arp" enabled,
we default na_mcast_to_ucast to true if "proxy_arp" is already
enabled.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/20596
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Plasma Cloud MCX3 Media Converter is a 3 port multi-GBit switch with
2x 10/100/1000/2500BaseT Ethernet ports and 1x SFP+ module slot.
Hardware:
- RTL9302C SoC
- Macronix MX25L25645G (32MB flash)
- Winbond W632GU6rB-11 (256MB DDR3 SDRAM)
- RTL8224 4x 10m/100m/1/2.5 Gigabit PHY
- IC+ IP802AR POE+ PSE controller
The media converter is powered by 54 Volts 1.2A barrel connector. The
internal TTL serial connector can be used to access the terminal. Pins from
1: TX RX (unused) GND. Serial connection is via 115200 baud, 8N1.
A reset button is accessible through a hole next to the SFP+ module slot.
Installation
------------
* The device can be flashed by using sysupgrade command. Either from the
original vendor firmware or using an initramfs (see "Debug")
* Connect serial as per the layout above. Connection parameters: 115200 8N1
* The image must be copied using scp to /tmp of the device
scp openwrt-realtek-rtl930x-plasmacloud_mcx3-squashfs-sysupgrade.bin root@[IP address of the device]:/tmp/
* start sysupgrade without saving the original vendor configuration
sysupgrade -n /tmp/openwrt-realtek-rtl930x-plasmacloud_mcx3-squashfs-sysupgrade.bin
Installation via u-boot
-----------------------
If you have an TFTP server connected to the switch, it is possible to
directly install the device using the factory image from u-boot
# setup networking and IP of TFP server
rtk network on
setenv ipaddr 10.100.100.99
setenv serverip 10.100.100.20
# get factory image
tftp 0x84000000 factory.bin
# erase firmware partitions
sf probe 0
sf erase 0x100000 0x01f00000
# write firmware to both partitions
sf write ${fileaddr} 0x100000 ${filesize}
sf write ${fileaddr} 0x1080000 ${filesize}
# adjust the boot commands
setenv bootargs "mtdparts=spi0.0:896k(u-boot),64k(u-boot-env),64k(u-boot-env2),15872k(inactive),15872k(firmware2)"
setenv bootcmd "rtk init; bootm 0xb5080000"
# restart
reset
Debug
-----
* Connect serial as per the layout above. Connection parameters: 115200 8N1.
* A tftp server is required, tftpd-hpa works well.
* Power the device, at U-Boot start rapidly hit Esc key to stop autoboot
* Enable network:
rtk network on
* Change ip address of device:
setenv ipaddr 192.168.1.6
* Download initramfs from TFTP server:
tftpboot 0x84000000 192.168.1.111:openwrt-realtek-rtl930x-plasmacloud_mcx3-initramfs-kernel.bin
* Boot loaded file:
bootm 0x84000000
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20625
Signed-off-by: Robert Marko <robimarko@gmail.com>
The raw option inside 'config wifi-iface' is called hostapd_bss_options,
not hostapd_options.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20657
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
`list address` entries in /etc/config/dhcp are sometimes (I'm not sure
about the exact conditions) passed to upstream resolver, bypassing local
resolution. Adding them (minus the IP) to --local prevents this. In the
configuration, this means that
# /etc/config/dhcp
list address '/hello.com/world.com/1.2.3.4'
list address '/foo.com/bar.com/4.3.2.1'
which previously translated into
# /var/etc/dnsmasq.conf.*
address=/hello.com/world.com/1.2.3.4
address=/foo.com/bar.com/4.3.2.1
now becomes
# /var/etc/dnsmasq.conf.*
address=/hello.com/world.com/1.2.3.4
local=/hello.com/world.com/
address=/foo.com/bar.com/4.3.2.1
local=/foo.com/bar.com/
This behaviour is controlled by the `address_as_local` boolean option, which
defaults to false (old behaviour). openwrt/luci#7957 adds support for this flag
to LuCI.
A workaround for a small list of domains is to add them to `option local`,
but this is very tedious to do for every `list address` entry and dnsmasq
limits this option to 1024 characters.
Signed-off-by: Marko Zajc <marko@zajc.tel>
Link: https://github.com/openwrt/openwrt/pull/18610
Signed-off-by: Robert Marko <robimarko@gmail.com>
Because the firmware has not yet been accepted in linux-firmware we
cannot yet package mt7987-2p5g-phy-firmware-internal. Remove it from
DEVICE_PACKAGES of the BPi-R4-mini until the an upcoming linux-firmware
release will come with this firmware included, allowing us to then
create that package.
Fixes: 8b6c6978d6 ("mediatek: add support for BananaPi BPi-R4 Lite")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The RTL930x and RTL931x have an ingress and egress bandwidth controller for
each port. They can can be used to reduce the throughput for each port.
They can be programmed via the the DSA flower offloading capabilities. Only
a limited functionality (bytes based rate limiter for ingress/egress) is
supported.
With kmod-sched-act-police, kmod-sched-flower and tc installed, each port
can have its ingress/egress rate limit applied in hardware using:
# tc qdisc del dev lan1 clsact
tc qdisc add dev lan1 clsact
tc filter add dev lan1 ingress flower skip_sw action police rate 100mbit burst 64k conform-exceed drop
tc filter add dev lan1 egress flower skip_sw action police rate 150mbit burst 64k conform-exceed drop
Signed-off-by: Issam Hamdi <ih@simonwunderlich.de>
Co-developed-by: Sven Eckelmann <se@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20663
Signed-off-by: Robert Marko <robimarko@gmail.com>
In commit 042996b46b compilation of git repos is made to fail when PKG_MIRROR_HASH is not correct.
It looks like it was forgotten that in openwrt there is a posibility to set the PKG_MIRROR_HASH to "skip".
In this case the hash check should not be performed and compilation should continue as expected.
This is especially very usefull when doing local testing and development with git repos.
Signed-off-by: Matthias Franck <matthias.franck@softathome.com>
Link: https://github.com/openwrt/openwrt/pull/20655
Signed-off-by: Robert Marko <robimarko@gmail.com>
PKG_NAME was lost during package migration from "packages" feed to "main" feed.
Signed-off-by: Matthias Franck <matthias.franck@softathome.com>
Link: https://github.com/openwrt/openwrt/pull/20662
Signed-off-by: Robert Marko <robimarko@gmail.com>
On RTL930x, each SerDes pair shares a set of PLLs with different
capabilities (LC PLL: 1G/2.5G/10G, ring PLL: 1G/2.5G). In principle,
this allows any combination of speeds on a SerDes pair. However, it
creates a special case when trying to configure a SerDes for 10G while
the LC PLL is already in use at a slower speed for the neighbor SerDes.
The current implementation just gives up in that case. Instead, free up
the LC PLL by reconfiguring the neighbor SerDes to the ring PLL.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/20568
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit fixes mistaken executable bit on dts files.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20676
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
0aece3089a3a wifi: mt76: mt7996: Remove useless check in mt7996_msdu_page_get_from_cache()
05b3d899ad24 wifi: mt76: Move Q_READ/Q_WRITE definitions in dma.h
85e6517b0ac5 wifi: mt76: Add mt76_dev pointer in mt76_queue struct.
a3b6c67c97d2 wifi: mt76: Add the capability to set TX token start ID
141a81557070 wifi: mt76: Introduce the NPU generic layer
647d11bb17e0 wifi: mt76: mt7996: Add NPU offload support to MT7996 driver
8ff3b2bfc37f wifi: mt76: mt7996: fix typos in comments
0043147439b4 wifi: mt76: mt7925: refactor regulatory domain handling to regd.[ch]
f0e8fe441489 wifi: mt76: mt7925: refactor CLC support check flow
588cc87bf6a2 wifi: mt76: mt7925: refactor regulatory notifier flow
dac1d45fe94b wifi: mt76: mt7925: improve EHT capability control in regulatory flow
c166c4a0e750 wifi: mt76: mt7925: add auto regdomain switch support
d7b059bba166 wifi: mt76: mt7925: disable auto regd changes after user set
84f62a6beb99 wifi: mt76: mmio_*_copy fix byte order and alignment
f5ae5b2e8116 Revert "wifi: mt76: mt792x: improve monitor interface handling"
8ae7e6dc1d3a wifi: mt76: adjust BSS conf pointer handling
1b438ebe0d06 wifi: mt76: mt7925: cqm rssi low/high event notify
7519fa4ce62c wifi: mt76: mt7996: fix max nss value when getting rx chainmask
ea0580ad065f wifi: mt76: mt7996: no need to wait ACK event for SDO command
74112c2956fb wifi: mt76: mt7996: fix implicit beamforming support for mt7992
361d6bdac45d wifi: mt76: mt7996: support fixed rate for link station
d99274cdc30c wifi: mt76: mt7996: fix several fields in mt7996_mcu_bss_basic_tlv()
ad90a85b652b wifi: mt76: mt7996: fix teardown command for an MLD peer
e9fe8bc03e41 wifi: mt76: mt7996: set link_valid field when initializing wcid
050394665502 wifi: mt76: mt7996: use correct link_id when filling TXD and TXP
5d223855552c wifi: mt76: mt7996: fix MLD group index assignment
ab8361dbc421 wifi: mt76: mt7996: fix MLO set key and group key issues
7ce7ab881b3f wifi: mt76: mt7996: fix using wrong phy to start in mt7996_mac_restart()
1e0c23ff754b wifi: mt76: mt7996: fix EMI rings for RRO
eb567bc7f9b6 wifi: mt76: mt7925: ensure the 6GHz A-MPDU density cap from the hardware.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It is not necessary to have two different family_id checks directly after
another. It is simpler to just combine both into one.
Suggested-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20637
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The rtl838x_rate_control_init() and rtl839x_rate_control_init() functions
were never called because the rtl83xx_setup_qos() always returned after the
QoS configuration
Fixes: dc9cc0d3e2 ("realtek: add QoS and rate control")
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20637
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This mainly improve the CFLAGS handling on compilation of OpenSSL.
The CFLAGS are currently passed 2 times generating compilation warning
due to -fhonour-copts passed 2 times.
This can be improved by passing the CFLAGS as env to the OpenSSL
Configure tool.
For consistency we do the same for CPPFLAGS and LDFLAGS.
This permits to drop redundant flags in the Compile phase and from the
.conf file.
Link: https://github.com/openwrt/openwrt/pull/20665
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
symtom: macs not properly incremented (all macs the same)
solution: set correct offset to mac location
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20664
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
According to CMake documentation[1]:
[CMAKE_FIND_ROOT_PATH] is a list of directories that contain the
target environment.
[CMAKE_FIND_ROOT_PATH_MODE_PROGRAM] sets the default behavior for the
find_program command.
In most cases, find_program is used to search for an executable which
will then be executed, e.g. using execute_process or
add_custom_command. So in most cases an executable from the build host
is required, so setting CMAKE_FIND_ROOT_PATH_MODE_PROGRAM to NEVER is
normally preferred.
Since CMAKE_FIND_ROOT_PATH is set to the target staging dir, and the
toolchain root dir, it will find target programs before the host ones.
An example of this problem is if you try to build antiblock from the
packages feed after llvm from the video feeds is built. Antiblock will
search for clang-format, pickup the target version, and fail to build.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[1] https://cmake.org/cmake/help/book/mastering-cmake/chapter/Cross%20Compiling%20With%20CMake.html
Link: https://github.com/openwrt/openwrt/pull/20656
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
ba73bc4672ec CMakeLists: update cmake minimum required version to 3.10
988399770af1 libbb: CMakeLists: update cmake minimum required version to 3.10
ce546f3ebff5 opkg: CMakeLists: update cmake minimum required version to 3.10
80503d94e356 libopkg: CMakeLists: update cmake minimum required version to 3.10
Fixes: #20659
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The BPi-R4 Lite uses the same defaults like all other BananaPi boards
to store the bootloader environment on the boot media.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The BPi-R4 Lite is a WiFi-7 router board based on the MT7987 SoC.
Specification :
- SOC: Mediatek MT7987A (4x Cortex-A53
- RAM: 2GB
- Flash: 32MB SPI NOR, 256MB SPI NAND, 8GB eMMC
- Switch: MediaTek MT7531AE
- Ports : 4x LAN (1G), 1x SFP (via MT7531), 1x WAN (2.5G)
- Buttons : Reset & WPS/Mesh
- LEDs : Status (PWM), SFP
- USB: on-board VIA VL817 USB3.1/USB2.0 hub
* 1 - mPCIe B (SIM3)
* 2 - NGFF-KEYB (SIM1)
* 3 - USB-A connector
* 4 - mPCIe A (SIM4)
- mPCIe: 1x 8GT/s x2 or 2x 8GT/s x1 (configurable via bootloader)
- RTC: PCF8563
- mikroBUS socket with SPI, I2C and full UART
- on-board HT42B534 USB-to-serial for Type-C console port
- Power: USB Type-C PD 20V, or DC via barrel connector or JST-VH 3.96
Installation:
Uncompress *sdcard.img.gz and write to microSD card, eg. using 'dd'.
Use bootloader menu on the serial console to install SPI-NAND or SPI-NOR,
once installed to SPI-NAND you can use the bootloader menu to install to
eMMC. See instructions for BananaPi R3 for details.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The BPi R4 Lite can boot from microSD, SPI-NAND, SPI-NOR and eMMC.
Build menu-driven U-Boot for each storage option.
Provide options for installation from microSD to SPI-NAND and SPI-NOR,
and from SPI-NAND to eMMC (similar to BPi-R3).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import and clean DT and DT-overlay files from MediaTek's SDK to build
an image with various DT-overlays for the MT7987 reference board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import patches to use cpufreq voltage calibration data from the efuse on
MT7988, and add support for MT7987.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The MT7987 has two LVTS thermal sensors, one covering all CPU cores,
and one for the built-in 2.5GE PHY.
Add support for MT7987 to the LVTS thermal driver.
Thanks to Chad Monroe of Adtran for providing cleaned up patches for
Linux 6.6 which have been ported to Linux 6.12.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Compared to MT7988 (NETSYSv3) the Ethernet Frame Engine of MT7987
has been slighly updated (NETSYSv3.1), among other things the packet
scheduler (shaper) has apparently been reworked.
Import patches for basic support of the Ethernet Frame Engine of the
MT7987 SoC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The MT7987 is mostly a stripped-down low-pin-count version of the
MT7988 without the 10GBit/s SerDes. Most existing drivers can be reused.
Import to-be-sent-upstream patches doing all the groundwork for
basic support for the MT7987 SoC, adding clk, pinctrl and pwm support.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Build the (upstream) configuration for the MT7987 reference board, and
enable support for DT-overlay application which will be necessary to
use the image for the MT7987 RFB generated in OpenWrt.
Adapt our downstream patches (generic reset button, rootdisk selection)
for MT7987 to prepare for real-world boards.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Build TF-A for the MediaTek MT7987 SoC family.
Add necessary downstream patches in preparation for the BananaPi R4 Lite,
which connects both flash chips to SPI2 and got broken MMC bus.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Currently the detection of external-data FIT images works by checking
if the FIT structure is more than 4 kiB. However, for boards with lots
of different DT-overlays and configurations the FIT structure can
exceed 4 kiB which results in the FIT splitter to fail detecting the
rootfs.
Increase the threshold for external-data FIT to 512 kiB as there aren't
any kernel images smaller than that, and FIT structure less than 512 kiB
will always be an external-data FIT.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make functions in b53 static and add kernel
patch to fix prototype build errors
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20653
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
After switching to the 6.12 kernel, time to remove 6.6 support.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20614
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Linux 6.12 has been validated on Layerscape platforms, including NXP
reference boards and multiple custom designs. Tests covered system
boot, networking, storage, and common peripherals, with no regressions
observed.
Enable 6.12 as the default to continue broader testing and integration.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20614
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
On the LS1012A-FRDM both PHY reset pins are tied to GPIO1_23.
Up to Linux 6.6, pinctrl did not touch this GPIO and the reset
line remained in the state set by U-Boot. Starting from 6.12,
the kernel requires explicit configuration of this pin, otherwise
the PHYs fail to be detected.
This adds a gpio-hog node to ensure the reset line stays asserted,
fixing PHY detection on boot.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20614
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
warning print "ath11k c000000.wifi: failed to flush transmit queue 0"
is observed during busy times.
The mac80211 fallback implementation of `flush_sta` does not handle the per STA queues well.
This is fixed by providing a ath11k specific implementation of flush_sta telling the firmware to flush a given station.
The draining of the transmit queues should therefore stop correctly, even if new packets arrive in the mean time.
An upstream ath11k RFC is available at:
https://patchwork.kernel.org/project/linux-wireless/patch/GV1P250MB14333A5BF24623C4753A10E1E8E0A@GV1P250MB1433.EURP250.PROD.OUTLOOK.COM/
The patch was tested on a Xiaomi AX3600.
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Tested-by: Florian Maurer <f.maurer@outlook.de>
Co-authored-by: Benjamin Berg <benjamin@sipsolutions.net>
Tested-by: Flole <flole@flole.de>
Link: https://github.com/openwrt/openwrt/pull/20293
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop support for kernel 6.6 as now kernel 6.12 is set as default kernel
version.
Link: https://github.com/openwrt/openwrt/pull/20644
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move the ipq806x target to kernel 6.12 by default as every kernel bump
problem has been handled.
Link: https://github.com/openwrt/openwrt/pull/20644
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The Google OnHub doesn't init the SMEM in SBL causing the CPUFreq driver
to fail probe. This is caused by the fact that new CPUFreq driver makes
use of SMEM to identify the SoC variant and on Google OnHub this is not
available.
Backport patch to detect this state and fallback to compatible
matching fixing the CPUFreq driver.
Link: https://github.com/openwrt/openwrt/pull/20587
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Patch CMakeLists.txt for cmake 4.x compatibility.
New cmake versions require at least 3.5 as 'cmake_minimum_required'
in CMakeLists.txt. In future 3.10 will be required.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/20265
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Patch CMakeLists.txt in selected apps for cmake 4.x compatibility.
New cmake versions require at least 3.5 as 'cmake_minimum_required'
in CMakeLists.txt. In future 3.10 will be required.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/20265
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Patch CMakeLists.txt in selected apps for cmake 4.x compatibility.
New cmake versions require at least 3.5 as 'cmake_minimum_required'
in CMakeLists.txt. In future 3.10 will be required.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/20265
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Edit CMakeLists.txt to fulfill cmake 4.0 requirement that
cmake_minimum_required is now at least 3.5 and in future 3.10.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/20265
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Patch CMakeLists.txt to fulfill cmake 4.0 requirements
of cmake_minimum_required being at least 3.5 and in future 3.10.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/20265
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
d44af6dd8f4e dhcpv6: create struct dhcpv6_lease
4df45c8c3722 dhcpv4: create struct dhcpv4_lease
a6dccae41b60 odhcpd: struct lease -> struct lease_cfg
fc0abb66f122 dhcpv4: use leasetime from a->lease
74eeff193848 router: always use link-local src address for RAs
b9a071b8341f router: Rewrite the ingress MTU to one configured for the interface
1ef9e0e610d5 router: utilize interface ra_mtu for RA
1480c09ee0aa config: clamp ra_mtu to interface MTU, and default ra_mtu to interface MTU
ee4f0df6bd68 netlink: Store interface MTU at link change
d174e25e85a1 github: fix CI apt dependencies
8f393d55a76e odhcpd: more fixes for IID calculations
fc27940fe9...d44af6dd8f
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
