mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2026-03-08 04:27:09 +01:00
6ffe8a473e
The Seagate BlackArmor NAS220 is a consumer NAS
with two internal drive bays. The stock OS runs
RAID 1 over the disks via mdadm.
Device specification:
- SoC: Marvell 88F6192 800 MHz
- RAM: 128 MB
- Flash: 32 MB
- 2 x internal SATA II drives
- Ethernet: 10/100/1000 Mbps (single port, no switch)
- WLAN: None
- LED: Power, Status, Sata Activity
- Key: Power, Reset
- Serial: 10 pin header, (115200,8,N,1), 3.3V TTL
9|x - x|10
7|x - x|8
5|x - GND|6
3|x - RX|4
1|TX - x|2
front of case
- USB ports: 2 x USB 2.0
Flash instruction:
NOTE: this process uses a serial connection. It will upgrade the
bootloader and reset the bootloader environment variables
TFTP server setup
- Setup PC with TFTP server set the PC IP to 10.4.50.5 as TFTP server
- Copy these files to TFTP server location
- u-boot.kwb
- seagate_blackarmor-nas220-initramfs-uImage
- seagate_blackarmor-nas220-squashfs-sysupgrade.bin
- seagate_blackarmor-nas220-squashfs-factory.bin
Seagate NAS setup
- Connect LAN cable between PC and seagate device
- Connect to serial to seagate device
Install u-boot
- Boot seagate device and stop in bootloader by pressing any key
- run 'printenv' from u-boot and save the values
- tftpboot 0x2000000 u-boot.kwb
- nand erase.part uboot
- nand write 0x2000000 0x0 ${filesize}
- reset
Update MAC address in u-boot env
- Stop in u-boot by pressing any key
- Get your MAC address from your saved printenv. Is also on chassis
- setenv ethaddr <your MAC>
- saveenv
Option 1 (recommended) - Install OpenWrt via initramfs and sysupgrade
- tftpboot 0x2000000 seagate_blackarmor-nas220-initramfs-uImage
- bootm 0x2000000
- *OpenWrt should be running now, however it is not written to flash yet*
- From the running instance of OpenWrt use Luci's "flash image" feature
from the web site or use sysupgrade from the console to write
seagate_blackarmor-nas220-squashfs-sysupgrade.bin to flash
Option 2 - Install OpenWrt by flashing factory image from u-boot
- nand erase.part ubi
- tftpboot 0x2000000 seagate_blackarmor-nas220-squashfs-factory.bin
- nand write 0x2000000 ubi ${filesize}
- reset
Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
209 lines
5.6 KiB
Makefile
209 lines
5.6 KiB
Makefile
#
|
|
# Copyright (C) 2009-2013 OpenWrt.org
|
|
#
|
|
# This is free software, licensed under the GNU General Public License v2.
|
|
# See /LICENSE for more information.
|
|
#
|
|
|
|
include $(TOPDIR)/rules.mk
|
|
include $(INCLUDE_DIR)/image.mk
|
|
|
|
KERNEL_LOADADDR:=0x8000
|
|
|
|
define Device/dsa-migration
|
|
DEVICE_COMPAT_VERSION := 1.1
|
|
DEVICE_COMPAT_MESSAGE := Config cannot be migrated from swconfig to DSA
|
|
endef
|
|
|
|
define Device/Default
|
|
PROFILES := Default
|
|
DEVICE_DTS = kirkwood-$(lastword $(subst _, ,$(1)))
|
|
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
|
|
KERNEL := kernel-bin | append-dtb | uImage none
|
|
KERNEL_NAME := zImage
|
|
KERNEL_SUFFIX := -uImage
|
|
KERNEL_IN_UBI := 1
|
|
|
|
PAGESIZE := 2048
|
|
SUBPAGESIZE := 512
|
|
BLOCKSIZE := 128k
|
|
IMAGES := sysupgrade.bin factory.bin
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
IMAGE/factory.bin := append-ubi
|
|
SUPPORTED_DEVICES = $(subst _,$(comma),$(1))
|
|
endef
|
|
|
|
define Device/checkpoint_l-50
|
|
DEVICE_VENDOR := Check Point
|
|
DEVICE_MODEL := L-50
|
|
DEVICE_PACKAGES := kmod-ath9k kmod-gpio-button-hotplug kmod-mvsdio \
|
|
kmod-rtc-s35390a kmod-usb-ledtrig-usbport wpad-basic-wolfssl
|
|
IMAGES := sysupgrade.bin
|
|
endef
|
|
TARGET_DEVICES += checkpoint_l-50
|
|
|
|
define Device/cisco_on100
|
|
DEVICE_VENDOR := Cisco Systems
|
|
DEVICE_MODEL := ON100
|
|
KERNEL_SIZE := 5376k
|
|
KERNEL_IN_UBI :=
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
|
|
DEVICE_PACKAGES := kmod-mvsdio
|
|
SUPPORTED_DEVICES += on100
|
|
endef
|
|
TARGET_DEVICES += cisco_on100
|
|
|
|
define Device/cloudengines_pogoe02
|
|
DEVICE_VENDOR := Cloud Engines
|
|
DEVICE_MODEL := Pogoplug E02
|
|
DEVICE_DTS := kirkwood-pogo_e02
|
|
SUPPORTED_DEVICES += pogo_e02
|
|
endef
|
|
TARGET_DEVICES += cloudengines_pogoe02
|
|
|
|
define Device/cloudengines_pogoplugv4
|
|
DEVICE_VENDOR := Cloud Engines
|
|
DEVICE_MODEL := Pogoplug V4
|
|
DEVICE_DTS := kirkwood-pogoplug-series-4
|
|
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 kmod-mvsdio kmod-usb3 \
|
|
kmod-gpio-button-hotplug
|
|
endef
|
|
TARGET_DEVICES += cloudengines_pogoplugv4
|
|
|
|
define Device/iom_iconnect-1.1
|
|
DEVICE_VENDOR := Iomega
|
|
DEVICE_MODEL := Iconnect
|
|
DEVICE_DTS := kirkwood-iconnect
|
|
SUPPORTED_DEVICES += iconnect
|
|
endef
|
|
TARGET_DEVICES += iom_iconnect-1.1
|
|
|
|
define Device/iom_ix2-200
|
|
DEVICE_VENDOR := Iomega
|
|
DEVICE_MODEL := StorCenter ix2-200
|
|
DEVICE_DTS := kirkwood-iomega_ix2_200
|
|
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 \
|
|
kmod-gpio-button-hotplug kmod-hwmon-lm63
|
|
PAGESIZE := 512
|
|
SUBPAGESIZE := 256
|
|
BLOCKSIZE := 16k
|
|
KERNEL_SIZE := 3072k
|
|
KERNEL_IN_UBI :=
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE_SIZE := 31744k
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
|
|
check-size
|
|
endef
|
|
TARGET_DEVICES += iom_ix2-200
|
|
|
|
define Device/linksys
|
|
DEVICE_VENDOR := Linksys
|
|
DEVICE_PACKAGES := kmod-mwl8k wpad-basic-wolfssl kmod-gpio-button-hotplug
|
|
KERNEL_IN_UBI :=
|
|
UBINIZE_OPTS := -E 5
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
|
|
endef
|
|
|
|
define Device/linksys_e4200-v2
|
|
$(Device/linksys)
|
|
$(Device/dsa-migration)
|
|
DEVICE_MODEL := E4200
|
|
DEVICE_VARIANT := v2
|
|
KERNEL_SIZE := 2688k
|
|
SUPPORTED_DEVICES += linksys,viper linksys-viper
|
|
endef
|
|
TARGET_DEVICES += linksys_e4200-v2
|
|
|
|
define Device/linksys_ea3500
|
|
$(Device/linksys)
|
|
$(Device/dsa-migration)
|
|
DEVICE_MODEL := EA3500
|
|
PAGESIZE := 512
|
|
SUBPAGESIZE := 256
|
|
BLOCKSIZE := 16k
|
|
KERNEL_SIZE := 2624k
|
|
SUPPORTED_DEVICES += linksys,audi linksys-audi
|
|
endef
|
|
TARGET_DEVICES += linksys_ea3500
|
|
|
|
define Device/linksys_ea4500
|
|
$(Device/linksys)
|
|
$(Device/dsa-migration)
|
|
DEVICE_MODEL := EA4500
|
|
KERNEL_SIZE := 2688k
|
|
SUPPORTED_DEVICES += linksys,viper linksys-viper
|
|
endef
|
|
TARGET_DEVICES += linksys_ea4500
|
|
|
|
define Device/raidsonic_ib-nas62x0
|
|
DEVICE_VENDOR := RaidSonic
|
|
DEVICE_MODEL := ICY BOX IB-NAS62x0
|
|
DEVICE_DTS := kirkwood-ib62x0
|
|
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4
|
|
SUPPORTED_DEVICES += ib62x0
|
|
endef
|
|
TARGET_DEVICES += raidsonic_ib-nas62x0
|
|
|
|
define Device/seagate_blackarmor-nas220
|
|
DEVICE_VENDOR := Seagate
|
|
DEVICE_MODEL := Blackarmor NAS220
|
|
DEVICE_PACKAGES := kmod-hwmon-adt7475 kmod-fs-ext4 kmod-ata-marvell-sata \
|
|
mdadm kmod-gpio-button-hotplug
|
|
PAGESIZE := 512
|
|
SUBPAGESIZE := 256
|
|
BLOCKSIZE := 16k
|
|
UBINIZE_OPTS := -e 1
|
|
endef
|
|
TARGET_DEVICES += seagate_blackarmor-nas220
|
|
|
|
define Device/seagate_dockstar
|
|
DEVICE_VENDOR := Seagate
|
|
DEVICE_MODEL := FreeAgent Dockstar
|
|
SUPPORTED_DEVICES += dockstar
|
|
endef
|
|
TARGET_DEVICES += seagate_dockstar
|
|
|
|
define Device/seagate_goflexnet
|
|
DEVICE_VENDOR := Seagate
|
|
DEVICE_MODEL := GoFlexNet
|
|
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4
|
|
SUPPORTED_DEVICES += goflexnet
|
|
endef
|
|
TARGET_DEVICES += seagate_goflexnet
|
|
|
|
define Device/seagate_goflexhome
|
|
DEVICE_VENDOR := Seagate
|
|
DEVICE_MODEL := GoFlexHome
|
|
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4
|
|
SUPPORTED_DEVICES += goflexhome
|
|
endef
|
|
TARGET_DEVICES += seagate_goflexhome
|
|
|
|
define Device/zyxel_nsa310b
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := NSA310b
|
|
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-r8169 kmod-fs-ext4 \
|
|
kmod-gpio-button-hotplug kmod-hwmon-lm85
|
|
SUPPORTED_DEVICES += nsa310b
|
|
endef
|
|
TARGET_DEVICES += zyxel_nsa310b
|
|
|
|
define Device/zyxel_nsa310s
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := NSA310S
|
|
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 kmod-gpio-button-hotplug
|
|
endef
|
|
TARGET_DEVICES += zyxel_nsa310s
|
|
|
|
define Device/zyxel_nsa325
|
|
DEVICE_VENDOR := ZyXEL
|
|
DEVICE_MODEL := NSA325
|
|
DEVICE_VARIANT := v1/v2
|
|
DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 \
|
|
kmod-gpio-button-hotplug kmod-rtc-pcf8563 kmod-usb3
|
|
SUPPORTED_DEVICES += nsa325
|
|
endef
|
|
TARGET_DEVICES += zyxel_nsa325
|
|
|
|
$(eval $(call BuildImage))
|