Mikhail Zhilkin d1ff5681b4 mediatek: add support for Routerich BE7200 ... This PR adds support for Routerich BE7200 router. Specification ------------- - SoC : MediaTek MT7987A Quad-core ARM Cortex-A53 2.0 GHz - RAM : 1024 MiB DDR4 - Flash : SPI-NAND 512 MiB (Giga Device) - WLAN : MediaTek MT7992E, WiFi 7 - 2.4 GHz : b/g/n/ax, MIMO 4x4 - 5 GHz : a/n/ac/ax, MIMO 4x4 - Ethernet : 10/100/1000 Mbps x3 (LAN, Airoha AN8855AE) 10/100/1000/2500 Mbps x1 (WAN, SoC internal phy) - USB : 3.0 x1 - Buttons : Mesh, Reset - LEDs : 1x Status (blue), gpio-controlled 1x WiFi (blue), gpio-controlled 1x mesh (blue), gpio-controlled 3x LAN activity (blue), gpio-controlled 1x WAN activity (blue), gpio-controlled 1x WAN no-link (red), gpio-controlled - Power : 12 VDC, 1.5 A Installation ------------ 1. Update stock firmware via the web interface (don't keep settings). Update U-Boot (optional) ------------------------ After installing OpenWrt, you may want to install opensource U-Boot. 1. Install kmod-mtd-rw: apk update && apk add kmod-mtd-rw 2. Unlock bootloader: insmod mtd-rw i_want_a_brick=1 mtd unlock BL2 mtd unlock FIP 3. Download and write open-source BL2 and FIP: cd /tmp wget https://.../openwrt-mediatek-filogic-routerich_be7200-preloader.bin wget https://.../openwrt-mediatek-filogic-routerich_be7200-bl31-uboot.fip mtd write /tmp/openwrt-mediatek-filogic-routerich_be7200-preloader.bin BL2 mtd write /tmp/openwrt-mediatek-filogic-routerich_be7200-bl31-uboot.fip FIP 4. Reboot the router. Return to stock --------------- 1. Update OpenWrt wirh the vendor's firmware (don't keep settings). Recovery (original U-Boot) ----------------------------- 1. Press Reset button and power on the router. After ~10 sec release the button; 2. Upload and flash squashfs-sysupgrade.itb image via the web interface. Recovery (open-source U-Boot) ----------------------------- 1. Place OpenWrt 'openwrt-mediatek-filogic-routerich_be7200-initramfs-recovery.itb' image on the tftp server (IP: 192.168.1.254) 2. Press Reset button and power on the router. After ~10 sec release the button. 3. Use OpenWrt initramfs system for recovery Recovery (full disaster) ------------------------ Use UART and mtk_uartboot tool. Link: https://github.com/981213/mtk_uartboot USB power control ----------------- Disable: echo disabled > /sys/devices/platform/usb-power/state Enable: echo enabled > /sys/devices/platform/usb-power/state UART ---- UART pins are silkscreened on the PCB. Don't connect Vcc. Serial connection parameters: 115200, 8n1, 3.3V MAC addresses ------------- +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | WAN | 24:0f:5e:xx:xx:30 | label | | LAN | 24:0f:5e:xx:xx:31 | label+1 | | WLAN 2g | 24:0f:5e:xx:xx:32 | label+2 | | WLAN 5g | 24:0f:5e:xx:xx:33 | label+3 | +---------+-------------------+-----------+ The WLAN 2g MAC was found in 'Factory', 0x4 Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> Link: https://github.com/openwrt/openwrt/pull/21235 (cherry picked from commit ff5e66a920) Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> Link: https://github.com/openwrt/openwrt/pull/21383 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>		2026-01-05 00:53:01 +01:00
..
imagebuilder	imagebuilder: fix repeated generation of package index when signing is enabled	2025-11-12 21:23:33 +08:00
linux	mediatek: add support for Routerich BE7200	2026-01-05 00:53:01 +01:00
llvm-bpf	build: use zstd for IB, toolchain, SDK and LLVM compression	2024-04-13 08:05:04 +02:00
sdk	sdk: use GIT_COMMIT for buildbot SDK	2025-12-04 19:20:55 +01:00
toolchain	build: use zstd for IB, toolchain, SDK and LLVM compression	2024-04-13 08:05:04 +02:00
Config.in	targets: add USES_PM auto-feature	2025-07-20 12:16:13 +01:00
Makefile	build: add $(STAGING_DIR) and $(BIN_DIR) preparation to target and package subdir compile dependencies	2024-03-03 23:13:59 +01:00