mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2026-03-14 23:09:45 +01:00
No description
bc18c2bfe7
This board was used in dual-band 802.11n enterprise access points, models BSAP-1800v2 and BSAP-1840, introduced in 2010 by Bluesocket, which was acquired by Adtran in 2011, who has now EOL'ed them. They differed only in that the BSAP-1840's antennae were detachable, while the BSAP-1800v2's were inside the case. They have an external RJ-45 console port, which works with standard Cisco 72-3383-01 console cables. Specification: - System-On-Chip: AR7161 - CPU/Speed: 600 MHz - Flash-Chip: Macronix MX25L12845E - Flash size: 16 MiB - RAM: 64 MiB - Wireless No1: Lite-On WN2601A card: AR9160/AR9103 2.4GHz 802.11bgn - Wireless No2: Lite-On WN2502A card: AR9160/AR9106 5GHz 802.11an - PHY: Vitesse VSC8601, Rev. B Installation: 1. Connect to the serial console using a terminal that supports YMODEM at 115200 bps, 8 data bits, no parity, 1 stop bit 2. Interrupt the bootloader using its password, which is: r00t 3. Issue the "fis init" command, confirming if prompted 4. Look at the length of the openwrt-ath79-generic-*-squashfs-kernel.bin file, and substitute it below, instead of where I have "LeNgTh" 5. Issue the following command, and upload this file using YMODEM protocol load -r -v -b 0x80060000 -m ymodem 6. Issue the following commands, substituting as mentioned above: fis create -b 0x80060000 -l LeNgTh vmlinux_2 load -r -v -b 0x80100000 -m ymodem 7. Using YMODEM, upload openwrt-ath79-generic-*-squashfs-rootfs.bin 8. Issue the "fis free" command, and for the first range in its response, use a hexadecimal calculator to subtract the start from the end in order to substitute it below, with the leading "0x" to specify it in hexadecimal, instead of where I have "LeNgTh" 9. Issue the following commands, substituting as mentioned above: fis create -b 0x80100000 -l LeNgTh -e 0 -r 0 rootfs reset 10.Wait for the status LED to go solid green Tested-by: Brian Gonyer <bgonyer@gmail.com> Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [fixed obsolete $ARGV in platform_do_upgrade] Signed-off-by: Petr Štetiar <ynezz@true.cz> |
||
|---|---|---|
| .github | ||
| config | ||
| include | ||
| package | ||
| scripts | ||
| target | ||
| toolchain | ||
| tools | ||
| .gitattributes | ||
| .gitignore | ||
| BSDmakefile | ||
| Config.in | ||
| feeds.conf.default | ||
| LICENSE | ||
| Makefile | ||
| README | ||
| rules.mk | ||
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
This is the buildsystem for the OpenWrt Linux distribution.
To build your own firmware you need a Linux, BSD or MacOSX system (case
sensitive filesystem required). Cygwin is unsupported because of the lack
of a case sensitive file system.
You need gcc, binutils, bzip2, flex, python, perl, make, find, grep, diff,
unzip, gawk, getopt, subversion, libz-dev and libc headers installed.
1. Run "./scripts/feeds update -a" to obtain all the latest package definitions
defined in feeds.conf / feeds.conf.default
2. Run "./scripts/feeds install -a" to install symlinks for all obtained
packages into package/feeds/
3. Run "make menuconfig" to select your preferred configuration for the
toolchain, target system & firmware packages.
4. Run "make" to build your firmware. This will download all sources, build
the cross-compile toolchain and then cross-compile the Linux kernel & all
chosen applications for your target system.
Sunshine!
Your OpenWrt Community
http://www.openwrt.org