9c8d634646
The pinmux-related registers on the RTL930X SoC family are spread across
various non-consecutive registers. It might be tempting to modify them
directly in a specific driver (SPI, LED, etc.), but this would cause issues
with parallel, non-locked read-modify-write operations, which are required
to update individual portions of these registers.
Instead, it is better to use the devicetree pinctrl properties to define
the correct configurations for the various operation modes.
One important setting here is the LED Sync bit. This allows the LED
controller to generate an additional positive edge on the `STCP`
("STore Clock Pin", also known as `RCLK`) of the LED shift register after
the actual content has already been shifted in using the normal shift
clock. The LED shift register is then expected to copy the content from the
shift register section into the storage registers, which act as the actual
LED output control. This functionality is available in, and commonly used
with, the SNx4HC595 family of shift registers.
To activate it, simply register it in the default state of the
"realtek,rtl83xx-switch" node:
&switch0 {
pinctrl-names = "default";
pinctrl-0 = <&pinmux_enable_led_sync>;
....
};
It would be nicer when this can be directly added to the led subnode. But
for this to work, `realtek,rtl9300-leds` must first be an actual driver
(known to the driver core).
[1] https://www.ti.com/lit/ds/symlink/sn74hc595.pdf
Suggested-by: Bevan Weiss <bevan.weiss@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://github.com/openwrt/openwrt/pull/19815
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
||
|---|---|---|
| .devcontainer/ci-env | ||
| .github | ||
| .vscode | ||
| config | ||
| include | ||
| LICENSES | ||
| package | ||
| scripts | ||
| target | ||
| toolchain | ||
| tools | ||
| .gitattributes | ||
| .gitignore | ||
| BSDmakefile | ||
| Config.in | ||
| COPYING | ||
| feeds.conf.default | ||
| Makefile | ||
| README.md | ||
| rules.mk | ||
OpenWrt Project is a Linux operating system targeting embedded devices. Instead of trying to create a single, static firmware, OpenWrt provides a fully writable filesystem with package management. This frees you from the application selection and configuration provided by the vendor and allows you to customize the device through the use of packages to suit any application. For developers, OpenWrt is the framework to build an application without having to build a complete firmware around it; for users this means the ability for full customization, to use the device in ways never envisioned.
Sunshine!
Download
Built firmware images are available for many architectures and come with a package selection to be used as WiFi home router. To quickly find a factory image usable to migrate from a vendor stock firmware to OpenWrt, try the Firmware Selector.
If your device is supported, please follow the Info link to see install instructions or consult the support resources listed below.
An advanced user may require additional or specific package. (Toolchain, SDK, ...) For everything else than simple firmware download, try the wiki download page:
Development
To build your own firmware you need a GNU/Linux, BSD or macOS system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.
Requirements
You need the following tools to compile OpenWrt, the package names vary between distributions. A complete list with distribution specific packages is found in the Build System Setup documentation.
binutils bzip2 diff find flex gawk gcc-6+ getopt grep install libc-dev libz-dev
make4.1+ perl python3.7+ rsync subversion unzip which
Quickstart
-
Run
./scripts/feeds update -ato obtain all the latest package definitions defined in feeds.conf / feeds.conf.default -
Run
./scripts/feeds install -ato install symlinks for all obtained packages into package/feeds/ -
Run
make menuconfigto select your preferred configuration for the toolchain, target system & firmware packages. -
Run
maketo build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.
Related Repositories
The main repository uses multiple sub-repositories to manage packages of
different categories. All packages are installed via the OpenWrt package
manager called opkg. If you're looking to develop the web interface or port
packages to OpenWrt, please find the fitting repository below.
-
LuCI Web Interface: Modern and modular interface to control the device via a web browser.
-
OpenWrt Packages: Community repository of ported packages.
-
OpenWrt Routing: Packages specifically focused on (mesh) routing.
-
OpenWrt Video: Packages specifically focused on display servers and clients (Xorg and Wayland).
Support Information
For a list of supported devices see the OpenWrt Hardware Database
Documentation
Support Community
- Forum: For usage, projects, discussions and hardware advise.
- Support Chat: Channel
#openwrton oftc.net.
Developer Community
- Bug Reports: Report bugs in OpenWrt
- Dev Mailing List: Send patches
- Dev Chat: Channel
#openwrt-develon oftc.net.
License
OpenWrt is licensed under GPL-2.0