mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2026-02-17 13:11:12 +01:00
8da24b1109
The TP-link Deco X80-5G is a AX WIFI router with a single 1G (LAN) and 1 2.5G (WAN) port with a built in Quectel 5G modem. Specifications: Architecture ARMv8-A (aarch64 Cortex A53, 4 cores) Vendor Qualcomm Bootloader U-Boot (2016) System-On-Chip Qualcomm IPQ8074A (Networking Pro 1210 platform) CPU/Speed 2.2GHZ Flash-Chip ESMT F59D1G81MB-45TI 1G-bit NAND Flash MB 128MB (1Gbit) RAM-chip 2* ESMT M15T4G16256A-DEBG2G 2Gb DDR3L (32bit) RAM MB 512MB (4Gbit) WLan System-On-Chip (5g) Qualcomm QCN5054 WLan Front end modules (5g) 8* Qorvo QPF4588 WLAN (5G) A/N/AC/AX WLAN Antenna (int) 8* (4 shared with 2.5G) WLan System-On-Chip (2.4G) Qualcomm QCN5024 WLan Front end modules (2.4G) 4* Skyworks SKY85340-11 WLAN (2.4G) B/G/N/AX WLAN Antenna (int) 4* (shared with 5g) Eithernet-phy (1Gbit) Qualcomm (Atheros) AR8033-AL1A Ethernet (1Gbit) 1* Eithernet-phy (2.5Gbit) Qualcomm QCA8081 Ethernet (2.5Gbit) 1* Switch Embedded in the SOC? Serial 1.8v 8n1 (testpoints) Modem System-On-Chip Qualcomm 5G RG50xQ (Snapdragon X55 platform) 5G modem capability 5000Mbps down 900Mbps up 5G modem bands N1/N3/N5/N7/N8/N20/N28/N38/N40/N41/N77/N78/N79 4G modem capability 4.5G LTE-Advanced Pro (Cat20 down 2Gbps) (Cat18 up 200Mbps) 4G modem FDD bands B1/B3/B5/B7/B8/B18/B19/B20/B26/B28 4G modem TDD bands B34/B38/B39/B40/B41/B42/B43 Modem antenna (int) 8* (5G/4G use) Modem antenna (ext) 2* SMA connectors (5G/4G use) SIM type 1* Nano SIM Telephony 1* POTS RJ11 (see wiki for more info:) https://openwrt.org/inbox/toh/tp-link/x80-5g_v1 Notes: Installation Instructions: Between antennas 7 and 8 on the PCB with the RGB harness there are three test pads labelled TP1 TP2 and TP3 connections are as follows: |TP2|-- RX |TP1|-- TX |TP3|-- GND RX requires an external pullup to operate somewhere around 5 K ohm but your luck may vary the Uart is 1.8v Set a static IP and set up a tftpserver and terminal. power the router and quickly type the magic string “tpl” and press enter to break into u-boot in the shell set the environment variables to enable tftp booting setenv ipaddr (routerIP) setenv serverip (server IP) load you initramfs: tftpboot 0x44000000 (serverIP):openwrt-qualcommax-ipq807x-tplink_x80-5g-initramfs-uImage.itb boot your initramfs bootm upload your factory image to /tmp format and install the factory image: ubiformat /dev/mtd12 -y -f /tmp/openwrt-qualcommax-ipq807x-tplink_x80-5g-squashfs-factory.ubi Note as this device swaps root partitions upon update your boot partition may be set as mtd13 Update script to mount factory tplink partition's for MAC recovery and device data. Capture Labelmac from Factory_data partition. Patch LAN from Labelmac. Patch ART from Labelmac. Set GPIO to make modem operational from boot. GPIO fan tables work like the stock device with three fan maps high active idle with a top fan speed of 6800 RPM. High temp 70 deg speeds 6-8 Active temp 50 deg speeds 2-5 low temp 25 degree speed 0-1 Signed-off-by: jonathan brophy <professor_jonny@hotmail.com> Link: https://github.com/openwrt/openwrt/pull/16329 Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
|---|---|---|
| .. | ||
| airoha | ||
| apm821xx | ||
| archs38 | ||
| armsr | ||
| at91 | ||
| ath79 | ||
| bcm27xx | ||
| bcm47xx | ||
| bcm53xx | ||
| bcm4908 | ||
| bmips | ||
| d1 | ||
| gemini | ||
| generic | ||
| imx | ||
| ipq40xx | ||
| ipq806x | ||
| ixp4xx | ||
| kirkwood | ||
| lantiq | ||
| layerscape | ||
| loongarch64 | ||
| malta | ||
| mediatek | ||
| mpc85xx | ||
| mvebu | ||
| mxs | ||
| octeon | ||
| omap | ||
| pistachio | ||
| qoriq | ||
| qualcommax | ||
| qualcommbe | ||
| ramips | ||
| realtek | ||
| rockchip | ||
| sifiveu | ||
| siflower | ||
| starfive | ||
| stm32 | ||
| sunxi | ||
| tegra | ||
| uml | ||
| x86 | ||
| zynq | ||
| Makefile | ||