mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2026-02-17 13:11:12 +01:00
0a2b3b66db
Hardware specs:
- NXP T4240, 12C/24T @ 1.67 GHz
- 3 × 2 GB DDR3 SO-DIMM
- 128 MB NOR flash
- 2 GB SLC NAND
- SD card interface
- PCIe: x4 and x8
- SATA 3 Gbps
- 8 × 1 GbE
- 4 × 10 GbE SFP
- RTC
This commit adds the sysupgrade and factory images for T4240RDB board in
both variants:
- nor: for booting and read whole system from NOR memory
- sdboot: for booting and read whole system from SD card
SD Card images install:
- Burn image to sdcard. E.g:
gunzip -c gunzip -c openwrt-qoriq-generic-fsl_T4240RDB-squashfs-sdcard.img.gz | \
sudo dd of=/dev/mmcblk0 conv=fsync,notrunc status=progress bs=4M && sync
- Download lastest Cortina PHY firmware from NXP github [1], if you accept their
EULA [2].
- Install Cortina PHY on image, E.g:
dd if=cs4315-cs4340-PHY-ucode.txt of=/dev/mmcblk0 bs=1 seek=2M
- Insert SD-Card to SD slot
- Switch SW3.4 to OFF
- Configre mac addresses from sticker in u-boot. E.g:
setenv ethaddr 00:10:f3:3a:a8:66
setenv eth1addr 00:10:f3:3a:a8:67
setenv eth2addr 00:10:f3:3a:a8:68
setenv eth3addr 00:10:f3:3a:a8:69
setenv eth4addr 00:10:f3:3a:a8:6a
setenv eth5addr 00:10:f3:3a:a8:6b
setenv eth6addr 00:10:f3:3a:a8:6c
setenv eth7addr 00:10:f3:3a:a8:6d
setenv eth8addr 00:10:f3:3a:a8:6e
setenv eth9addr 00:10:f3:3a:a8:6f
setenv eth10addr 00:10:f3:3a:a8:70
setenv eth11addr 00:10:f3:3a:a8:71
saveenv
- reset and boot
NOR images install:
- download and extract factory image on tftp server root
- boot device and stop in u-boot (from nor or sd card u-boot)
- configure server and ip address. E.g:
setenv ipaddr 192.168.1.2
setenv serverip 192.168.1.1
- Download image and run flashing:
tftpboot $loadaddr openwrt-qoriq-generic-fsl_T4240RDB-squashfs-factory-nor.bin
protect off all
erase $fwaddr +$filesize
cp.b $loadaddr $fwaddr $filesize
- Switch SW3.4 to ON
- Switch SW3.1-3 to OFF
- reboot
- Do postprocessing (see bellow)
NOR images post processing:
- Configre mac addresses from sticker in u-boot. E.g:
setenv ethaddr 00:10:f3:3a:a8:66
setenv eth1addr 00:10:f3:3a:a8:67
setenv eth2addr 00:10:f3:3a:a8:68
setenv eth3addr 00:10:f3:3a:a8:69
setenv eth4addr 00:10:f3:3a:a8:6a
setenv eth5addr 00:10:f3:3a:a8:6b
setenv eth6addr 00:10:f3:3a:a8:6c
setenv eth7addr 00:10:f3:3a:a8:6d
setenv eth8addr 00:10:f3:3a:a8:6e
setenv eth9addr 00:10:f3:3a:a8:6f
setenv eth10addr 00:10:f3:3a:a8:70
setenv eth11addr 00:10:f3:3a:a8:71
saveenv
- boot
- Download and refresh RCW stored in eeprom:
tr '\0' '\377' < /dev/zero | dd bs=256 of=/sys/bus/i2c/devices/0-0050/eeprom
cat /tmp/openwrt-qoriq-generic-fsl_T4240RDB-squashfs-rcw.bin > /sys/bus/i2c/devices/0-0050/eeprom
- Download lastest Cortina PHY firmware from NXP github [1], if you accept their
EULA [2].
- Install Cortina PHY on image, E.g:
mtd write cs4315-cs4340-PHY-ucode.txt /dev/mtd4
- reset and boot
[1] https://raw.githubusercontent.com/nxp-qoriq/qoriq-firmware-cortina/refs/tags/lf-6.12.34-2.1.0/cs4315-cs4340-PHY-ucode.txt
[2] https://github.com/nxp-qoriq/qoriq-firmware-cortina/blob/lf-6.12.34-2.1.0/EULA.txt
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/10941
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
|
||
|---|---|---|
| .. | ||
| airoha | ||
| apm821xx | ||
| armsr | ||
| at91 | ||
| ath79 | ||
| bcm27xx | ||
| bcm47xx | ||
| bcm53xx | ||
| bcm4908 | ||
| bmips | ||
| d1 | ||
| econet | ||
| gemini | ||
| generic | ||
| imx | ||
| ipq40xx | ||
| ipq806x | ||
| ixp4xx | ||
| kirkwood | ||
| lantiq | ||
| layerscape | ||
| loongarch64 | ||
| malta | ||
| mediatek | ||
| microchipsw | ||
| mpc85xx | ||
| mvebu | ||
| mxs | ||
| octeon | ||
| omap | ||
| pistachio | ||
| qoriq | ||
| qualcommax | ||
| qualcommbe | ||
| ramips | ||
| realtek | ||
| rockchip | ||
| sifiveu | ||
| siflower | ||
| starfive | ||
| stm32 | ||
| sunxi | ||
| tegra | ||
| uml | ||
| x86 | ||
| zynq | ||
| Makefile | ||