Prevent flashing truncated or otherwise corrupted uImage.FIT images
by verifying checksums and hashes of all sub-images before flashing
using the newly packaged fit_check_sign tool.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add all boards using uImage.FIT to platform_check_image() case section
making sure we are dealing with a FIT image.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The board name that goes into /etc/board.json and is used by sysupgrade
for image verifications gets determined by the below command:
`strings /proc/device-tree/compatible | head -1`
as per package/base-files/files/lib/preinit/02_sysinfo
On more recent firmware version for the Pine64 RockPro64 v2.1 devices the
first entry is 'pine64,rockpro64-v2.1' however the metadata in the
sysupgrade image only specifies 'pine64,rockpro64' as supported and image
verification will fail.
This change makes it so the image metadata will contain both
'pine64,rockpro64' and 'pine64,rockpro64-v2.1' allowing image verification
to pass on both older and more recent firmware versions.
Signed-off-by: Sam Hegarty <hegarty.sam@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18542
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The IPQ5018 GE Phy driver registers two fixed rate clocks which are
passed on to the GCC which gatekeeps and passes them back to the phy.
Fix 'bad phandle' warning and tell consumer (GCC) how many cells to
expect when compiling.
Warning (clocks_property): /soc@0/clock-controller@1800000: Missing property '#clock-cells' in node /soc@0/mdio@88000/ethernet-phy@7 or bad phandle (referred from clocks[5])
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18548
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Xiaomi MiWiFi 3A wireless router has a similar system architecture as the Xiaomi Mi 4A router, which is already officially supported by OpenWrt.
Product website: https://www.mi.com/miwifi3a
Device specification
--------------------
SoC: MT7628AN MIPS_24KEc @ 580 MHz 2.4G-bgn 2x2
WiFi: MT7612EN 5G-an, ac 80 MHz 2T2R
Flash: 16 MB
DRAM: 64 MB
Switch: MT7628AN (integrated in SoC)
Ethernet: 1 x 10 /100 Mbps
USB: None
Antennas: 2 x 2,4 GHz and 2 x 5 GHz (all are external and non-detachable)
LEDs: blue/red/amber
Buttons: Reset
Serial: 115200,8n1
MAC addresses as verified by OEM firmware:
------------------------------------------
use address source
LAN *:DD factory 0x28
WAN *:DD factory 0x28
2g *:DE factory 0x4
5g *:DF factory 0x8004
OEM firmware uses VLAN's to create the network interface for WAN and LAN.
Bootloader info:
----------------
The stock bootloader uses a "Dual ROM Partition System".
OS1 is a deep copy of OS2.
The bootloader starts OS2 by default.
To force start OS1 it is needed to set "flag_try_sys2_failed=1".
How to install:
---------------
1- Use OpenWRTInvasion to gain Telnet, SSH and FTP access: https://github.com/acecilia/OpenWRTInvasion
[IP: 192.168.31.1 | Username: root | Password: root | FTP-Port: 21]
2- Connect to router using telnet or ssh.
3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0". Copy /tmp/mtd0 to computer using ftp.
4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3a-squashfs-sysupgrade.bin to /tmp in router using ftp.
5- Enable UART access and change start image to OS1.
nvram set uart_en=1
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set flag_try_sys2_failed=1
nvram commit
6- Erase OS1 & OS2 and install OpenWrt
mtd erase OS1
mtd erase OS2
mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3a-squashfs-sysupgrade.bin OS1
Credits:
--------
This PR is based on the work of Zehao Zhang (Github: @ZZH-Finalize) that he had published in the PR: #15698
Signed-off-by: Olgun Demir <olgun.demir@mail.com.tr>
Link: https://github.com/openwrt/openwrt/pull/18427
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for GL.iNET (AX3000) B3000.
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Winbond W634GU6NQB-11 (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
* Wi-Fi: QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (3 Ports 10/100/1000 GBASE-T)
* Flash: Winbond W25N01GWZEIG (128 MiB)
* LEDs: 1x single-color blue LED (GPIO 24 Active High)
1x single-color white LED (GPIO 23 Active High)
* Buttons: 1x Reset (GPIO 27 Active Low)
Flash Instructions:
*** The .img files are now universal ! ***
Openwrt --> openwrt-qualcommax-ipq50xx-glinet_gl-b3000-squashfs-factory.img
GL.iNet OEM --> openwrt-b3000-4.5.18-0731-1722397535.img
Either file can be flashed, in any of the available upgrade options, in both Firmwares.
Pick a file .. pick a method .. and SEND IT !!
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17903
Signed-off-by: Robert Marko <robimarko@gmail.com>
This adds the Thermal framework support for STM32MP157.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18119
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In modules.mk, sort packages in alphabetical order.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18119
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move kmod-phy-stm32-usbphyc in the "USB Support" menu and kmod-stm32-timers
in "Other modules" menu.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18119
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add STM32MP157C-DK2 support. This profile also supports the STM32MP157F-DK2
board. The only difference between these two boards is the CPU frequency
(650MHz for 157C and 800MHz for 157F).
A SCMI variant is available. With this variant the reset and clock
resources are provided by OP-TEE and the associated SCMI services.
It is the configuration recommended by STMicroelectronics, with secured
system resources.
The specifications bellow only list supported features.
Specifications
--------------
SOC: STM32MP157C
RAM: 512 MiB
Storage: SD Card
Ethernet: 1x 1 Gbps
Wireless: 2.4GHz Cypress CYW43455 (802.11b/g/n)
LEDs: Heartbeat (Blue)
USB: 4x 2.0 Type-A
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18119
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patch 87cb0446b7 also applies to higher kernel versions.
To apply to them it has been moved to a separate file in pending.
Fixes: 87cb0446b7 ("generic: fix broken TCP fraglist GRO patch")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18511
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix an error while building target/linux x64 on macOS 15.4 host,
due to the PATH_MAX macro being redefined:
mkdir -p /Volumes/test/openwrt/build_dir/target-x86_64_musl/linux-x86_64/linux-6.6.86/tools/objtool && make O=/Volumes/test/openwrt/build_dir/target-x86_64_musl/linux-x86_64/linux-6.6.86 subdir=tools/objtool --no-print-directory -C objtool
exec-cmd.c:15:9: error: 'PATH_MAX' macro redefined [-Werror,-Wmacro-redefined]
15 | #define PATH_MAX 4096
| ^
/Applications/Xcode.app/Contents/Developer/Platforms/MacOSX.platform/Developer/SDKs/MacOSX.sdk/usr/include/sys/syslimits.h:103:9: note: previous definition is here
103 | #define PATH_MAX 1024 /* max bytes in pathname */
| ^
exec-cmd.c is compiled as part of objtool to run on the host, and
therefore host headers are used, where PATH_MAX is already defined.
Using an old OpenWRT snapshot from 2025-02-16, where linux-6.6.77
used to build correctly, does not help. Reverting from Xcode 16.3 to
16.2 does not help either.
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18530
Signed-off-by: Robert Marko <robimarko@gmail.com>
The WL-WN573HX3 is an AX3000 outdoor Access Point by WAVLINK,
also sold in Europe as 7Links WLR-1300 (ZX-5612).
Specifications:
- MT7981B + MT7976 AX3000 2x2 DBDC (160 MHz)
- 16 MiB SPI NOR, 256 MiB RAM
- Gigabit ethernet port, 802.3af PoE
- IP67 outdoor case for wall or pole mounting with
four single band RP-SMA fiberglass antennas (8 dBi)
Installation:
- OEM Web UI is at 192.168.30.1 which will forward to
http://netlogin.link (using a captive portal)
- login with default password `admin`
- skip setup wizard by navigating directly to
http://netlogin.link/html/meshUpgrade.html
- upload WN573HX3-sysupgrade.bin
- reset to factory defaults to discard OEM UCI settings
MAC address assignment:
LAN 80:xx:xx:76:xx:25 hw 0x44e
WLAN 2.4G 80:xx:xx:76:xx:27 factory 0x04 (label MAC)
WLAN 5G 82:xx:xx:46:xx:27
pair key 8a:xx:xx:76:xx:27 also on label, not used by OpenWrt
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Specifications:
SoC: Mediatek MT7621AT (880 MHz MIPS dual-core, quad-thread, CPU)
512 Megabyte DDR3 SDRAM
32 Megabyte NOR Flash
4 Gigabit RJ45 PoE ports
2 MT7615N wifi chips (2.4GHz and 5GHz)
2 USB ports (1xUSB2 and 1xUSB3 - GL3510 chip)
RJ45 RS232 port on front panel (Max3232 chip)
2x mPCIe 2.0 slots for 4G/5G cards
2x SIM slot
1x SDCard Slot
Power via DC12V
4x Cell Antennae
4x Wifi Antennae
MAC Address Locations:
Purpose Ex. Partition Offset
2.4 Ghz *:01 factory 0x4
5 GHz *:02 factory 0x8004
LAN *:03 factory 0xe000
WAN *:04 factory 0xe006
MAC address prefix E4:3A:65 is registered to MofiNetwork Inc
and used as the prefix for all MAC addresses.
Manual: https://mofinetwork.com/files/MoFi_Network_MOFI5500_5GXeLTE_EM7690_SPECS.pdf
WiFi chip specs: https://www.mediatek.com/products/broadband-wifi/mt7615
CPU chip specs: https://www.mediatek.com/products/home-networking/mt7621
Teardown Pictures: https://fccid.io/2AE6X-MOFI5500/Internal-Photos/Internal-Photos-5591739
Installation:
Update Mofi 5500 to at least stock firmware version 4.8.6. (Available on the Mofi website.)
Previous versions are untested in the upgrade process. Log into the LuCI web interface,
usually at 192.168.10.1 and visit the 'System->Backup/Flash Firmware' page.
Upload and flash the firmware as usual.
Note to Maintainers: Do not remove SUPPORTED_DEVICES from the Makefile!
The customized Mofi version of OpenWRT (stock firmware) expects to see mofi5500 as the device
name. The stock firmware does not allow for forcing an installation.
Without this line, users cannot upload the new firmware through the stock Mofi firmware.
This device uses cell modems that could use QMI or MBIM.
Add LuCI Modem Manager to allow people to use these. Also, if they have
two cell network cards, ethernet, USB, or other kinds of networks, they may wish
to use MWAN3 to allow failover amongst their networks.
Please compile it with mwan3 for multiple WAN connections.
Co-authored-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Rick Mac Gillis <noreply@rickmacgillis.com>
Upstream version of ARM gc sections skip eeping some section. It was
reported some kernel load hang hence restore what we original did and
introduce a new patch that add the additional entry on top of the
upstream version.
Fixes: #18500
Fixes: 7843f21c51 ("generic: replace ARM gc sections patch with upstream version")
Tested-by: Stefan Kalscheuer <stefan@stklcode.de> (Turris Omnia)
Link: https://github.com/openwrt/openwrt/pull/18503
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some regression were reported with the backported upstream version. Old
kernel require an additional flush in some case and this was handled in
the old downstream patch.
Reintroduce the flush to fix the regression and refresh affected patch.
Fixes: f63d64ede0 ("generic: move patch from pending to backport")
Link: https://github.com/openwrt/openwrt/pull/18501
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The ATS SFP GT-T quirk patch was backported to stable kernel 6.6 but
was not notice while bumping the kernel version as they listed the quirk
at the bottom of the SFP quirk table while our hack patch put it at the
top.
With migrating to the upstream version, the duplication was made more
apparent.
Drop the double entry for the SFP module as it's already there and not
needed and refresh patches.
Link: https://github.com/openwrt/openwrt/pull/18484
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop GC sections ARMv7 patch as the new upstream version already handle
it by disabling the config in the specific EFI boot stub driver.
Link: https://github.com/openwrt/openwrt/pull/18464
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace ARM gc sections patch with upstream version. It seems this
feature is finally supported upstream with some minor difference.
In theory the upstream version should cut even more stuff, this really
needs to be evaluated if it's OK also to handle regression with the
kernel 6.12 update.
Link: https://github.com/openwrt/openwrt/pull/18464
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace SFP ignore TX FAULT with upstream version by backporting the 2
related upstream patch. Refresh SFP affected patch.
Link: https://github.com/openwrt/openwrt/pull/18464
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move all patch that got merged upstream from pending to backport and add
related tag. This is to make it easier to update to kernel 6.12.
Patch 680 required some special care as the upstream version had to be
split in a series of 6 patch.
Referesh all affected patch.
Link: https://github.com/openwrt/openwrt/pull/18464
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix execution of initramfs image on NEC Aterm devices by increasing
available memory for lzma extraction of lzma-loader.
The size of initramfs image of v24.10.0 exceeds available memory
(LZMA_TEXT_START - LOADADDR) and loader data running at LZMA_TEXT_START
will be overwritten by extracted data. As a result, LZMA extraction will
be broken and stuck (or unexpectedly reset).
Fix that issue by setting higher LZMA_TEXT_START address to increase
available memory for LZMA extraction by lzma-loader.
log (v24.10.0):
boot> tftpd
tftpd start 192.168.0.1
boot> start tftp load openwrt-24.10.0-ath79-generic-ne
end tftp load length = 6569768
start memory load ...
memory load complete
begin : 0x80040000
length : 6567044
startup: 0x80040000
boot> boot
begin : 0x80040000
length : 6567044
startup: 0x80040000
option: 0x0
NEC Aterm series (QCA9558)
Calibrating SGMII
SGMII cal value = 0xe
Configuring SGMII force mode
SGMII_CONFIG : 0x000000a2
MR_AN_CONTROL: 0x00008140
MR_AN_CONTROL: 0x00000140
OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Decompressing kernel... [:<syntax:value>]');retu <--- (stuck)
IPL:SOFT-RESET <--- (reset by WDT)
memory test ... ok
flinstall OK
boot version: 1.0.0
...
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18476
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that all packages that relied on the skip mechanism are selected
via BUILD_DEVICES or by defaulting for the subtarget drop them from
individual DEVICE_PACKAGES so that Image Builder works again for armv7.
Fixes: #18411
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that all packages that relied on the skip mechanism are selected
via BUILD_DEVICES or by defaulting for the subtarget drop them from
individual DEVICE_PACKAGES so that Image Builder works again for armv8_64b.
Fixes: #18412
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, bcm63xx-cfe is being installed into kernel build dir, however
that does not work for Image Builder as only certain artifacts from kernel
build dir are included in Image Builder.
So, simply install bcm63xx-cfe into image staging dir so its artifacts can
be used in Image Builder as well.
Fixes: #18408Fixes: #18409
Link: https://github.com/openwrt/openwrt/pull/18463
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Radxa ROCK 4SE[1] is a single board computer using the Rockchip
RK3399-T.
Hardware
--------
- Dual-core Cortex-A72 and quad-core Cortex-A53 CPU
- Mali-T860MP4 GPU
- LPDDR4 4GB RAM
- M.2 M Key slot (PCIe 2.1 x4)
- eMMC connector
- microSD card slot
- Wi-Fi 5 (not supported)
- Gigabit Ethernet with PoE support (additional PoE HAT required)
- USB 3.0 Type-A OTG port
- USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- USB Type-C power port (5V only)
- 40 Pin GPIO header
[1] https://radxa.com/products/rock4/4se
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to the micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/17554
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 4C+[1] is a single board computer with dual HDMI using
the Rockchip RK3399-T.
Hardware
--------
- Dual-core Cortex-A72 and quad-core Cortex-A53 CPU
- Mali-T860MP4 GPU
- LPDDR4 4GB RAM
- eMMC connector
- microSD card slot
- Wi-Fi 5 (not supported)
- Gigabit Ethernet with PoE support (additional PoE HAT required)
- USB 3.0 Type-A OTG port
- USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- USB Type-C power port (5V only)
- 40 Pin GPIO header
[1] https://radxa.com/products/rock4/4cp
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to the micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/17554
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Mercusys MR80X(EU) v3 router.
Device specification:
- SoC: Mediatek MT7981b, Cortex-A53, 64-bit
- RAM: 512MB
- Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
- Ethernet: 4x 100/1000 Mbps LAN1,LAN2,LAN3 & WAN
- Wireless: 2.4GHz (802.11 b/g/n/ax)
- Wireless: 5GHz (802.11 a/n/ac/ax)
- LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled LEDs
on ethernet ports
- Buttons: 1 (Reset)
- Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
slots contain "seconduboot" (also U-Boot 2022.01-rc4)
Installation (UART):
- Place OpenWrt initramfs-kernel image on tftp server with IP 192.168.1.2
- Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'.
- Set the uboot environment for startup.
setenv tp_boot_idx 0; setenv bootcmd bootm 0x46000000; saveenv
If the bootarg is set to boot from ubi1, also change it to ubi0.
- Load and run OpenWrt initramfs image.
setenv serverip 192.168.1.2; setenv ipaddr 192.168.1.1; tftpboot initramfs-kernel.bin; bootm
- Browse IP 192.168.1.1, upload the 'sysupgrade' image and do upgrade.
Recovery:
- Press Reset button and power on the router.
- Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware.
Stock layout:
0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"
ubi0/ubi1 format:
U-Boot at boot checks that all volumes are in place:
+-------------------------------+
| Volume Name: uboot Vol ID: 0|
| Volume Name: kernel Vol ID: 1|
| Volume Name: rootfs Vol ID: 2|
+-------------------------------+
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| label | 94:0C:xx:xx:xx:12 | label |
| WAN | 94:0C:xx:xx:xx:13 | label+1 |
| LAN | 94:0C:xx:xx:xx:12 | label |
| WLAN 2g | 94:0C:xx:xx:xx:11 | label-1 |
| WLAN 5g | 94:0C:xx:xx:xx:10 | label-2 |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file
"default-mac".
Signed-off-by: Schneider Azima <Schneider-Azima12@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/18181
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
USXGMII link-up may fail due to too short delay after PLL reset.
Increase the delay to fix this.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fixes to PCS driver to support 2.5G PHY
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Missing bus clock prevent access to NSSCC registers and thus it is
impossible change clock configuration, when ethernet connection speed
changes.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patches that fix:
* Wrong MSI interrups for PCIe3
* Hang during reboot due to stopped clocks
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
It seems new kernel version introduced -Wmissing-prototypes. This new
warning reported drivers that define non static function that are used
statically in the driver.
Fix this by declaring making those function actually static if not
defined in any header and not used outside of the single driver.
Co-authored-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18455
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
It seems new kernel linux version reorganized the header include and now
of.h needs to be explicitly included. This should have been done from
when the driver was introduced.
Add the missing of.h header to fix compilation error in later kernel
version.
Co-authored-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18455
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The reason phy fails to probe without explicitly overrided phy id is
that the reset timing fails to match. Fix it with proper `reset-delay-us` and
`reset-post-delay-us`.
While at it, change LED settings to match EAP610-Outdoor.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18450
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specification:
SoC: MediaTek MT7628AN
RAM: 128 MB, Zentel A3R1GE40JBF-8E
Flash: 16MB, Winbond W25Q128JV
Switch: rt3050-esw, 2 ports 100 Mbps
WiFi: MediaTek mt7628-wmac 2.4GHz 802.11n and MediaTek MT7663 5GHz
802.11ac (PCIe)
WWAN: Quectel EC200A-EL 4G modem (USB)
GPIO:
* 1 button (Reset/WPS)
* 6 LEDs (Power+WPS, LAN, 3xSignal)
* USB port power controls
* Modem reset
* Modem programming switch
* Internal/external antenna switch for 4G
Serial Interface:
TP10 - 3.3V can be used for level shifter, if needed
TP9 - TX
TP8 - RX
TP11 - GND
Interface properties: 115200, 8N1
Access to console using serial port for OEM firmware:
Username: admin
Password: 1234
Flashing via TFTP (no disassembling or soldering required):
1. Connect your PC and router to port LAN
2. Configure PC interface using static IP 192.168.1.225, mask
255.255.255.0
3. Place OpenWRT firmware image (*-squashfs-tftp-recovery.bin) to TFTP
root folder and renamed it to tp_recovery.bin
4. Unplug power from router
5. Press and hold Reset/WPS button
6. Power up the router
7. Wait until TFTP started uploading image (~10 seconds after power up)
and release Reset/WPS button
8. Wait until image uploaded, i.e. until LAN LED start lighting
9. Enable DHCP address on PC interface and wait for assigning address
10. Use ssh (root@192.168.1.1) to configure router properties
Depends on patch for firmware-utils package:
https://github.com/openwrt/firmware-utils/commit/2051fe5b
Signed-off-by: Sergii Shcherbakov <shchers@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17819
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: M16U4G16256A DDR4 512MB
Ethernet: 2x 2.5G + 3x 1G
USB: 1x USB 3.0
WiFi1: MT7975N 2.4GHz 4T4R
WiFi2: MT7975PN 5GHz 4T4R
Button: Reset, WPS
Power: DC 12V 2A
Flash instructions:
Connect to the router using ssh or telnet,
username: useradmin, password is the web
login password of the router.
Use scp to upload bl31-uboot.fip and flash:
"mtd write xxx-bl31-uboot.fip FIP"
"mtd erase ubi"
Connect to the router via the Lan port,
set a static ip of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
Download initramfs image, reboot router,
waiting for tftp recovery to complete.
After openwrt boots up, perform sysupgrade.
Note:
Back up all mtd partitions before flashing.
Signed-off-by: Yujie Zhu <libriunc@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18138
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_QCOM_IPA kernel cofig was enabled by mistake and conflicts with
mac80211 as it indirectly selects QMI HELPERS. Backports project provid
his own version of QMI HELPERS hence it should not be built-in.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Make the RPM partition read-only. This was a mistake and a leftover from
staging branch but I can take this mistake as an excuse to document the
current problem with RPM.
It might happen that a board ship with a broken RPM .mbn, broken not in
the sense that the board doesn't boot or it's a brick but broken in the
sense that it's outdaed and suffer from a bug fixed in new version.
This bug consist in a problem with the regulators between USB and NSS.
The old RPM mess with the NSS regulator (l2) and change the voltage for
it while configuring the USB regulator (l5).
This cause the ethernet subsystem to malfunction with the port not
working.
To workaround this, it's needed to disable RPM handling and CPUFreq.
With these 2 disabled, the old RPM doesn't touch regulators and Ethernet
works correctly.
New RPM correctly handle regulators for USB (l5) and doesn't suffer from
this problem. A solution for this is getting discussed with QCOM hoping
to get some good feedback for it.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add pending patch fixing NSSCC boot stall. These patch are needed to
prevent the ICC to disable critical clock for NSSCC NOC.
Without these the system will stall and reboot with watchdog.
While at it also remove an extra clock from DTSI as it currently have no
use. Original patch is not modified to keep consistency with series
proposed upstream.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant comment in NSSCC clock patch. The problem has been
identified hence the comment doesn't apply anymore.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Define default partition table for SPI-NAND mounted on reference board.
This is where is normally placed the rootfs UBI.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh dts SPI-NAND patch to to v14. This is to keep stuff synced with
current pending patch revision and make it easier to replace patch
later (and discover something broke in the meantime)
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
