This symbol was lost when porting to the 6.12 kernel.
Fixes: 16b5a77716 ("mediatek: mt7629: update config-6.12")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18947
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
New revision Arcadyan Mozart apply a new partition table and moved the
factory partition to a new location. This conflicts with the standard
partition layout and also make the nvmem cells to not correctly identify
the MAC address anymore.
Generate and Provide a new GPT partition table that account for the new
calibration partition.
The previous revision of the Arcadyan Mozart device is considered
pre-production devices and should not be intended for real support.
Link: https://github.com/openwrt/openwrt/pull/18874
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This allows us to use the full size of nand, which increases ubi size
from 64M to 122.25M.
If you are at factory firmware, please refer commit 63b8d98dd0 ("mediatek: add support for Cudy TR3000 v1")
to boot into OpenWrt initramfs (stock layout).
Flash instructions:
1. Login into the device and backup everything, especially 'Factory' part.
1. Unlock mtd partitions:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
3. Write new BL2 and FIP
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Tested-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Adapt patches adding NVMEM or fitblk rootdisk references to MMC
partitions for the changed MMC card binding.
Note that boards in 'dts' folder can only be converted once Linux 6.6,
which still depends on the old binding, has been dropped.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add patch to allow referencing MSDOS/MBR partitions in device tree to
allow legacy MT7623 boards to continue working with fitblk.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Replace downstream files by patches, either backports of those
which have already applied or pending patches tracked on patchwork.
This is done to make future maintainance more easy.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Drop patches which have been moved into target/linux/generic by commit
f4144d61d2 ("generic: 6.12: backport MediaTek Ethernet PHY changes").
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* the variant with 2.5G PHY instead of LAN SFP is called '2p5'
upstream and 'poe' in our downstream Linux 6.6 DT. Use the right
DTS depending on the kernel version and set an additional
compatible.
* drop additional DT overlay for WiFi.
The final version of the board uses a physical switch for the 12V
power of the WiFi module and the I2C EEPROM of the module always
comes empty (instead of with a MAC address).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In preparation of using the upstream mt7988a.dtsi when switching
to Linux 6.12 prepare by bringing our downstream version closer to
what went upstream.
* rename 'xphy' -> 'xsphy'
* rename 'uart[012]' -> 'serial[012]'
* only list pinctrl settings directly used in mt7988a.dtsi there,
leave it to boards to define all additional pinctrl settings
they need.
* move fan and thermal-zone to board level
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Upstream uses a different filename, so lets rename our downstream
mt7981.dtsi to mt7981b.dtsi and update the device tree of all
MT7981 boards accordingly.
This is to prepare for the switch to Linux 6.12 which is going to
use the upstream mt7981b.dtsi (plus some patches on top).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SOC: MediaTek MT7981b
RAM: 256MB DDR3
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7981b DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Interface MAC Algorithm
LAN 8C:AE:DB:2C:xx:xx label
WAN 8C:AE:DB:2C:xx:xx label +1
WLAN 2.4G 8C:AE:DB:2C:xx:xx label +2
WLAN 5G 8C:AE:DB:2C:xx:xx label +3
Installation
-------------------Install openwrt image-------------------------------:
Set a static ip on the ethernet interface of your PC. (ip address:
192.168.1.254, subnet mask:255.255.255.0) .
Download the OpenWrt uboot image
(openwrt-mediatek-filogic-snr_cpe-ax2-bl31-uboot.fip).
SSH/SCP opened by default on the stock firmware (3.0.1).
Username: Admin, default password: Admin. Check it on the bottom of
the router.
Copy uboot image using SCP (WinSCP) to /tmp dir on SNR-CPE-AX2.
Download recovery file.
openwrt-mediatek-filogic-snr_snr-cpe-ax2-initramfs-recovery.itb.
Copy the recovery image to a TFTP server reachable at 192.168.1.254/24.
Open ssh shell to the SNR-CPE-AX2.
Run commands:
mtd write \
/tmp/openwrt-mediatek-filogic-snr_snr-cpe-ax2-bl31-uboot.fip FIP
reboot
Wait until recovery boot.
Open web 192.168.1.1 and do sysupgrade by
openwrt-mediatek-filogic-snr_cpe-ax2-squashfs-sysupgrade.itb
Signed-off-by: Nikolay March <palladin82@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/18700
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Based on other mt7622 dts, it is not difficult to infer that the
missing interrupt controller is "pio". Fix dtc warning:
mt7622.dtsi:282.3-26: Warning (interrupts_property): /ethernet@1b100000/mdio-bus/ethernet-phy@7:#interrupt-cells: size is (8), expected multiple of 12
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Add missing #address-cells, #size-cells and #sound-dai-cells to
fix the following dtc warnings:
mt7986a-bananapi-bpi-r3-respeaker-2mics.dtso:46.5-18: Warning (reg_format): /fragment@1/__overlay__/wm8960@1a:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
mt7986a-bananapi-bpi-r3-respeaker-2mics.dtso:29.11-31.7: Warning (sound_dai_property): /fragment@0/__overlay__/sound_wm8960/codec: Missing property '#sound-dai-cells' in node /fragment@1/__overlay__/wm8960@1a or bad phandle (referred from sound-dai[0])
mt7986a-rfb-spim-nand.dts:17.12-19.5: Warning (sound_dai_property): /sound_wm8960/platform: Missing property '#sound-dai-cells' in node /soc/audio-controller@11210000 or bad phandle (referred from sound-dai[0])
mt7986a-rfb-spim-nand.dts:21.9-23.5: Warning (sound_dai_property): /sound_wm8960/codec: Missing property '#sound-dai-cells' in node /soc/i2c@11008000/wm8960@1a or bad phandle (referred from sound-dai[0])
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Trim unnecessary 0s to fix the following dtc warnings:
../dts/mt7981b-cudy-re3000-v1.dts:135.20-139.6: Warning (unit_address_format): /soc/spi@11009000/flash@0/partitions/partition@00000: unit name should not have leading 0s
../dts/mt7981b-cudy-wr3000-v1.dts:153.20-157.6: Warning (unit_address_format): /soc/spi@11009000/flash@0/partitions/partition@00000: unit name should not have leading 0s
../dts/mt7981b-gatonetworks-gdsp.dts:276.20-280.6: Warning (unit_address_format): /soc/spi@11009000/flash@0/partitions/partition@00000: unit name should not have leading 0s
mt7988a-rfb-spim-nor.dtso:36.21-39.7: Warning (unit_address_format): /fragment@0/__overlay__/flash@0/partition@00000: unit name should not have leading 0s
../dts/mt7981a-ubnt-unifi-6-plus.dts:113.28-131.6: Warning (unit_address_format): /soc/spi@11009000/flash@0/partitions/partition@00000: unit name should not have leading 0s
../dts/mt7981b-wavlink-wl-wn586x3.dts:147.20-151.6: Warning (unit_address_format): /soc/spi@11009000/flash@0/partitions/partition@00000: unit name should not have leading 0s
../dts/mt7981b-wavlink-wl-wn573hx3.dts:102.20-106.6: Warning (unit_address_format): /soc/spi@11009000/flash@0/partitions/partition@00000: unit name should not have leading 0s
../dts/mt7981b-yuncore-ax835.dts:161.20-165.6: Warning (unit_address_format): /soc/spi@11009000/flash@0/partitions/partition@00000: unit name should not have leading 0s
../dts/mt7986a-zyxel-ex5601-t0-stock.dts:57.39-61.6: Warning (unit_address_format): /soc/spi@1100a000/spi_nand@0/partitions/partition@180000/nvmem-layout/macaddr@0004: unit name should not have leading 0s
../dts/mt7986a-zyxel-ex5601-t0-stock.dts:63.39-67.6: Warning (unit_address_format): /soc/spi@1100a000/spi_nand@0/partitions/partition@180000/nvmem-layout/macaddr@0024: unit name should not have leading 0s
../dts/mt7986a-zyxel-ex5601-t0-stock.dts:69.39-73.6: Warning (unit_address_format): /soc/spi@1100a000/spi_nand@0/partitions/partition@180000/nvmem-layout/macaddr@002a: unit name should not have leading 0s
../dts/mt7986a-zyxel-ex5601-t0-ubootmod.dts:56.39-60.6: Warning (unit_address_format): /soc/spi@1100a000/spi_nand@0/partitions/partition@180000/nvmem-layout/macaddr@0004: unit name should not have leading 0s
../dts/mt7986a-zyxel-ex5601-t0-ubootmod.dts:62.39-66.6: Warning (unit_address_format): /soc/spi@1100a000/spi_nand@0/partitions/partition@180000/nvmem-layout/macaddr@0024: unit name should not have leading 0s
../dts/mt7986a-zyxel-ex5601-t0-ubootmod.dts:68.39-72.6: Warning (unit_address_format): /soc/spi@1100a000/spi_nand@0/partitions/partition@180000/nvmem-layout/macaddr@002a: unit name should not have leading 0s
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Correct dts node name based on reg property to fix the
following dtc warnings:
mt7981-rfb-spim-nand.dtso:20.25-67.6: Warning (spi_bus_reg): /fragment@1/__overlay__/spi_nand@0: SPI bus unit address format error, expected "1"
mt7986a-rfb-spim-nand.dts:41.23-76.4: Warning (spi_bus_reg): /soc/spi@1100a000/spi_nand@0: SPI bus unit address format error, expected "1"
../dts/mt7981a-comfast-cf-e393ax.dts:135.23-206.4: Warning (spi_bus_reg): /soc/spi@1100a000/spi_nand@0: SPI bus unit address format error, expected "1"
../dts/mt7981b-openwrt-one.dts:305.10-342.4: Warning (spi_bus_reg): /soc/spi@1100a000/flash@0: SPI bus unit address format error, expected "1"
../dts/mt7986a-zyxel-ex5601-t0-common.dtsi:166.30-180.4: Warning (spi_bus_reg): /soc/spi@1100a000/spi_nand@0: SPI bus unit address format error, expected "1"
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
The "gpio-export" driver doesn't require a "reg" property in the
device tree, hence we don't need to use the "#size-cells" property
to describe the size of "reg".
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18290
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add missing kmod-7915e package to get both wireless interfaces working.
Link: https://github.com/openwrt/openwrt/issues/18690
Reviewed-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Reduces boot time by 3s on a freshly installed image. This device
has a large flash and the gain can be higher with more packages
installed. According to the datasheet, this is the maximum frequency
supported by the Micron and Macronix chips that are installed in
these devices. Tested on three units over a two month period.
Before:
$ dd if=/dev/mtd5 of=/dev/null bs=10M count=1 status=progress
1+0 records in
1+0 records out
10485760 bytes (10 MB, 10 MiB) copied, 1.51901 s, 6.9 MB/s
After:
$ dd if=/dev/mtd5 of=/dev/null bs=10M count=1 status=progress
1+0 records in
1+0 records out
10485760 bytes (10 MB, 10 MiB) copied, 0.899474 s, 11.7 MB/s
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/18694
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
SOC: MediaTek MT7981b
RAM: 256MB DDR3
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7981b DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Installation
-----------------------------------------------------------
Vendor-UI Method
-----------------------------------------------------------
1. Download the OpenWrt initramfs.trx image.
2. Connect the PC via LAN to one of the yellow router ports and wait
until your PC to get a DHCP lease.
3. Browse to http://192.168.50.1
4. If your router is brand new, finish the setup process and log into
the Web-UI.
5. Navigate to Administration -> Firmware Upgrade and upload the
downloaded OpenWrt image.
6. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
-----------------------------------------------------------
TFTP Method
-----------------------------------------------------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.70/24. Rename the image to rtax52.bin.
2. Connect the PC with TFTP server to the RT-AX52.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
Conect to the serial console,
interrupt the autoboot process by pressing '4' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 rtax52.bin
$ bootm 0x46000000
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
---------------------------------------------------------------------------
Revert to stock firmware:
1: Download the rt-ax52 firmware from ASUS official website. Save
the firmware to tftp server directory and rename to RT-AX52.trx
2: Connect the PC with TFTP server to the RT-AX52.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
3: Conect to the serial console, power on again, interrupt the
autoboot process by pressing '4' when prompted.
$: ubi remove linux
$: ubi remove jffs2
$: ubi remove rootfs
$: ubi remove rootfs_data
$: ubi create linux 0x45fe000
$: reset
Then the dut will reboot,interrupt the autoboot process by
pressing '2' when prompted.
2: Load System code then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
$: enter y
you will see the follow, type enter directly:
Input device IP (192.168.1.1) ==:
Input server IP (192.168.1.70) ==:
Input Linux Kernel filename (RT-AX52.trx) ==:
4: wait for the device run up
Based on support for ASUS RT-AX52 by liudongdongdong7397
and trx image generation by remittor
Signed-off-by: Christoph Krapp <achterin@gmail.com>
This commit fixes mistaken executable bit on
mt7981b-mercusys-mr80x-v3.dts file.
Fixes: 7921e48d43 ("mediatek: add support for Mercusys MR80X v3")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
