The RPi upstream repo switched to the upstream SDHOST driver some time ago, so
it's time to do the same in our configs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit cd79b6ede9)
Import pending PXA I2C recovery fixes so that if I2C recovery is enabled in
the DTS it does not completely break I2C as it currently does since kernel
6.6.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit dfacae3049)
Backport upstream pinctrl fixes, these are required for the follow-up I2C
PXA recovery fixes.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 831994e258)
Commit d7e82c78d7 added a generic kernel patch that exposes a new
symbol REALTEK_PHY_HWMON when REALTEK_PHY and HWMON are enabled. The new
symbol was added to kmod-phy-realtek, but the kmod is not used in the
realtek target.
Fixes: d7e82c78d7 ("generic: backport Realtek PHY patches from upstream")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit ab87087672)
This fixes the handling of some FS copper SFP modules using the RollBall
protocol and needing some extra treatment.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
(cherry picked from commit bbe58f9830)
Sync jitterentropy source code with linux-6.12 to solve the
issue of jitterentropy initialization failed:
[ 9.523489] jitterentropy: Initialization failed with host not compliant with requirements: 9
[ 9.661916] kmodloader: 1 module could not be probed
[ 9.662377] kmodloader: - jitterentropy_rng - 0
In linux upstream commit cf27d9475f37 ("crypto: jitter - use
permanent health test storage"), when FIPS crypto is disabled,
the health test results are always explicitly skipped. That means
it will never return error code 9 (health test failed) again.
Fixes: https://github.com/openwrt/openwrt/issues/16684
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18399
(cherry picked from commit eec11fbbb6)
Link: https://github.com/openwrt/openwrt/pull/18822
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fixes the following warning:
[ 180.314652] NOHZ tick-stop error: local softirq work is pending, handler #08!!!
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 610dd871aa)
The web-recovery of the Genexis EX400 validates uploaded images to fit
in the rootf_0 partition.
With OpenWrt, only the kernel is stored in this partition, leaving the
partition very small. Currently, the first factory release image won't
be accepted by the recovery interface after the OpenWrt installation.
Pad the image of the ubifs to 10MB. This allows the 24.10 release image
to be uploaded, enabling device recovery.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit eea4689654)
bcm6328, bcm6362 and bcm6368 targets are missing a key config symbol which
prevents the NAND from working.
Fixes: f6c02b014d ("bmips: 6.1: refresh config and add missing symbols")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 61da745817)
Add missing kmod-7915e package to get both wireless interfaces working.
Link: https://github.com/openwrt/openwrt/issues/18690
Reviewed-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
Signed-off-by: Christoph Krapp <achterin@gmail.com>
(cherry picked from commit 0d6ba33181)
Configure the i2c pins as GPIO outputs and use the i2c-gpio driver to
control the Semtech SX9512 touch controller.
This fixes spurious errors in i2c transactions even at 1kHz with the
native i2c driver.
leds green:wan: Setting an LED's brightness failed (-6)
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit f828be4d10)
Add the necessary package dependencies as well as device-tree properties
to support the touch-inputs as well as missing LEDs on the Genexis Pulse
EX400 range extender.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 49a1781d74)
This driver is required for the touch-inputs as well as some LEDs on the
Genexis Pulse EX400.
The driver was also sent upstream. As the EX400 is currently the only
consumer, the driver is added target-specific for ramips.
Once the driver has been accepted upstream and is provided in a kernel
release used by OpenWrt, the package should be moved to the global input
drivers.
Link: https://www.spinics.net/lists/kernel/msg5669349.html
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 0842e79338)
The alternative model name does not need to be represented in the DTS.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit ff55daf1eb)
The Xiaomi MiWiFi 3A wireless router has a similar system architecture as the Xiaomi Mi 4A router, which is already officially supported by OpenWrt.
Product website: https://www.mi.com/miwifi3a
Device specification
--------------------
SoC: MT7628AN MIPS_24KEc @ 580 MHz 2.4G-bgn 2x2
WiFi: MT7612EN 5G-an, ac 80 MHz 2T2R
Flash: 16 MB
DRAM: 64 MB
Switch: MT7628AN (integrated in SoC)
Ethernet: 1 x 10 /100 Mbps
USB: None
Antennas: 2 x 2,4 GHz and 2 x 5 GHz (all are external and non-detachable)
LEDs: blue/red/amber
Buttons: Reset
Serial: 115200,8n1
MAC addresses as verified by OEM firmware:
------------------------------------------
use address source
LAN *:DD factory 0x28
WAN *:DD factory 0x28
2g *:DE factory 0x4
5g *:DF factory 0x8004
OEM firmware uses VLAN's to create the network interface for WAN and LAN.
Bootloader info:
----------------
The stock bootloader uses a "Dual ROM Partition System".
OS1 is a deep copy of OS2.
The bootloader starts OS2 by default.
To force start OS1 it is needed to set "flag_try_sys2_failed=1".
How to install:
---------------
1- Use OpenWRTInvasion to gain Telnet, SSH and FTP access: https://github.com/acecilia/OpenWRTInvasion
[IP: 192.168.31.1 | Username: root | Password: root | FTP-Port: 21]
2- Connect to router using telnet or ssh.
3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0". Copy /tmp/mtd0 to computer using ftp.
4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3a-squashfs-sysupgrade.bin to /tmp in router using ftp.
5- Enable UART access and change start image to OS1.
nvram set uart_en=1
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set flag_try_sys2_failed=1
nvram commit
6- Erase OS1 & OS2 and install OpenWrt
mtd erase OS1
mtd erase OS2
mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3a-squashfs-sysupgrade.bin OS1
Credits:
--------
This PR is based on the work of Zehao Zhang (Github: @ZZH-Finalize) that he had published in the PR: #15698
Signed-off-by: Olgun Demir <olgun.demir@mail.com.tr>
Link: https://github.com/openwrt/openwrt/pull/18427
(cherry picked from commit c3b8108a2b)
Link: https://github.com/openwrt/openwrt/pull/18550
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The WL-WN573HX3 is an AX3000 outdoor Access Point by WAVLINK,
also sold in Europe as 7Links WLR-1300 (ZX-5612).
Specifications:
- MT7981B + MT7976 AX3000 2x2 DBDC (160 MHz)
- 16 MiB SPI NOR, 256 MiB RAM
- Gigabit ethernet port, 802.3af PoE
- IP67 outdoor case for wall or pole mounting with
four single band RP-SMA fiberglass antennas (8 dBi)
Installation:
- OEM Web UI is at 192.168.30.1 which will forward to
http://netlogin.link (using a captive portal)
- login with default password `admin`
- skip setup wizard by navigating directly to
http://netlogin.link/html/meshUpgrade.html
- upload WN573HX3-sysupgrade.bin
- reset to factory defaults to discard OEM UCI settings
MAC address assignment:
LAN 80:xx:xx:76:xx:25 hw 0x44e
WLAN 2.4G 80:xx:xx:76:xx:27 factory 0x04 (label MAC)
WLAN 5G 82:xx:xx:46:xx:27
pair key 8a:xx:xx:76:xx:27 also on label, not used by OpenWrt
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Link: https://github.com/openwrt/openwrt/pull/18206
(cherry-picked from commit 907cb88e10)
Link: https://github.com/openwrt/openwrt/pull/18557
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Mercusys MR80X(EU) v3 router.
Device specification:
- SoC: Mediatek MT7981b, Cortex-A53, 64-bit
- RAM: 512MB
- Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
- Ethernet: 4x 100/1000 Mbps LAN1,LAN2,LAN3 & WAN
- Wireless: 2.4GHz (802.11 b/g/n/ax)
- Wireless: 5GHz (802.11 a/n/ac/ax)
- LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled LEDs
on ethernet ports
- Buttons: 1 (Reset)
- Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
slots contain "seconduboot" (also U-Boot 2022.01-rc4)
Installation (UART):
- Place OpenWrt initramfs-kernel image on tftp server with IP 192.168.1.2
- Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'.
- Set the uboot environment for startup.
setenv tp_boot_idx 0; setenv bootcmd bootm 0x46000000; saveenv
If the bootarg is set to boot from ubi1, also change it to ubi0.
- Load and run OpenWrt initramfs image.
setenv serverip 192.168.1.2; setenv ipaddr 192.168.1.1; tftpboot initramfs-kernel.bin; bootm
- Login as root via SSH (IP 192.168.1.1, port 22)
- Upload OpenWrt sysupgrade.bin image to the /tmp dir of the router
- Run sysupgrade:
sysupgrade -n /tmp/sysupgrade.bin
Recovery:
- Press Reset button and power on the router.
- Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware.
Stock layout:
0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"
ubi0/ubi1 format:
U-Boot at boot checks that all volumes are in place:
+-------------------------------+
| Volume Name: uboot Vol ID: 0|
| Volume Name: kernel Vol ID: 1|
| Volume Name: rootfs Vol ID: 2|
+-------------------------------+
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| label | 94:0C:xx:xx:xx:12 | label |
| WAN | 94:0C:xx:xx:xx:13 | label+1 |
| LAN | 94:0C:xx:xx:xx:12 | label |
| WLAN 2g | 94:0C:xx:xx:xx:11 | label-1 |
| WLAN 5g | 94:0C:xx:xx:xx:10 | label-2 |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file
"default-mac".
Signed-off-by: Schneider Azima <Schneider-Azima12@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/18181
(cherry picked from commit 7921e48d43)
Signed-off-by: Schneider Azima <Schneider-Azima12@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/18522
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patch 620-net_sched-codel-do-not-defer-queue-length-update.patch is
actually an ancient patch that somehow manage to be ported for 7 solid
years.
This comes from [1] where a fix patch was proposed. Nobody notice that
the proposed patch was actually rejected upstream in favor of [2]. And
the upstream fix patch is present in kernel from version 4.18.
This means that we were actually fixing for a non existant bug and maybe
introducing regression down the line.
Drop the patch for good as we already have a fix for it in flace for a
long time.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=109581
[2] 35b42da69e
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 0f9af6dcd9)
Link: https://github.com/openwrt/openwrt/pull/18730
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add network config for single-port Gateworks venice boards such that the
ethernet port is the WAN port instead of the default being a LAN port.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/18629
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 2d6f0275f8)
Hardware
--------
SOC: MediaTek MT7981b
RAM: 256MB DDR3
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7981b DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Installation
-----------------------------------------------------------
Vendor-UI Method
-----------------------------------------------------------
1. Download the OpenWrt initramfs.trx image.
2. Connect the PC via LAN to one of the yellow router ports and wait
until your PC to get a DHCP lease.
3. Browse to http://192.168.50.1
4. If your router is brand new, finish the setup process and log into
the Web-UI.
5. Navigate to Administration -> Firmware Upgrade and upload the
downloaded OpenWrt image.
6. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
-----------------------------------------------------------
TFTP Method
-----------------------------------------------------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.70/24. Rename the image to rtax52.bin.
2. Connect the PC with TFTP server to the RT-AX52.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
Conect to the serial console,
interrupt the autoboot process by pressing '4' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 rtax52.bin
$ bootm 0x46000000
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
---------------------------------------------------------------------------
Revert to stock firmware:
1: Download the rt-ax52 firmware from ASUS official website. Save
the firmware to tftp server directory and rename to RT-AX52.trx
2: Connect the PC with TFTP server to the RT-AX52.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
3: Conect to the serial console, power on again, interrupt the
autoboot process by pressing '4' when prompted.
$: ubi remove linux
$: ubi remove jffs2
$: ubi remove rootfs
$: ubi remove rootfs_data
$: ubi create linux 0x45fe000
$: reset
Then the dut will reboot,interrupt the autoboot process by
pressing '2' when prompted.
2: Load System code then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
$: enter y
you will see the follow, type enter directly:
Input device IP (192.168.1.1) ==:
Input server IP (192.168.1.70) ==:
Input Linux Kernel filename (RT-AX52.trx) ==:
4: wait for the device run up
Based on support for ASUS RT-AX52 by liudongdongdong7397
and trx image generation by remittor
Signed-off-by: Christoph Krapp <achterin@gmail.com>
(cherry picked from commit 50d9ca6e5a)
(remove factory image generation)
Signed-off-by: David Bauer <mail@david-bauer.net>
The factory image generation for the Genexis EX400 image currently fails
if CONFIG_TARGET_ROOTFS_INITRAMFS is disabled.
Create the factory image only if said config option is enabled to avoid
failing builds.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4e83d5ec26)
In case a broken fit image is present on flash the fitblk driver would
not map any /dev/fit* devices, but also not always close the block device
the image resides on. In case of ubiblock devices this is fatal as one
then cannot remove the ubiblock device (-EBUSY), and hence cannot replace
the broken image.
Always close the block device in case no sub-image was mapped.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 2b9c81d1cb)
Fix execution of initramfs image on NEC Aterm devices by increasing
available memory for lzma extraction of lzma-loader.
The size of initramfs image of v24.10.0 exceeds available memory
(LZMA_TEXT_START - LOADADDR) and loader data running at LZMA_TEXT_START
will be overwritten by extracted data. As a result, LZMA extraction will
be broken and stuck (or unexpectedly reset).
Fix that issue by setting higher LZMA_TEXT_START address to increase
available memory for LZMA extraction by lzma-loader.
log (v24.10.0):
boot> tftpd
tftpd start 192.168.0.1
boot> start tftp load openwrt-24.10.0-ath79-generic-ne
end tftp load length = 6569768
start memory load ...
memory load complete
begin : 0x80040000
length : 6567044
startup: 0x80040000
boot> boot
begin : 0x80040000
length : 6567044
startup: 0x80040000
option: 0x0
NEC Aterm series (QCA9558)
Calibrating SGMII
SGMII cal value = 0xe
Configuring SGMII force mode
SGMII_CONFIG : 0x000000a2
MR_AN_CONTROL: 0x00008140
MR_AN_CONTROL: 0x00000140
OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Decompressing kernel... [:<syntax:value>]');retu <--- (stuck)
IPL:SOFT-RESET <--- (reset by WDT)
memory test ... ok
flinstall OK
boot version: 1.0.0
...
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18476
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 10a674d277)
Convert the property variable type of "qcom,coexist-support" from
u32 to u8 to match the definition in the dt-bindings document.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18393
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3526dbabdc)
**Huasifei WH3000 eMMC / Fudy MT3000**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC.
MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ
**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8GB
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: power/reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1
**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.
**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.
**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-emmc-squashfs-sysupgrade.bin
```
**Factory MAC**
You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4`
```
dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C
```
**Enlarging a partition**
Though device has 8GB eMMC, it uses only 2GB `/dev/mmcblck0p6` as `rootfs` for `/rom` and `/overlay` leaving `/dev/mmcblck0p7` as empty unused space.
```
sgdisk -p /dev/mmcblk0
```
```
Disk /dev/mmcblk0: 15269888 sectors, 7.3 GiB
Sector size (logical/physical): 512/512 bytes
Disk identifier (GUID): 2BD17853-102B-4500-AA1A-8A21D4D7984D
Partition table holds up to 128 entries
Main partition table begins at sector 2 and ends at sector 33
First usable sector is 34, last usable sector is 14942174
Partitions will be aligned on 1024-sector boundaries
Total free space is 11197 sectors (5.5 MiB)
Number Start (sector) End (sector) Size Code Name
1 8192 9215 512.0 KiB 8300 u-boot-env
2 9216 13311 2.0 MiB 8300 factory
3 13312 21503 4.0 MiB 8300 fip
4 21504 29695 4.0 MiB 8300 config
5 29696 62463 16.0 MiB 8300 kernel
6 62464 4256767 2.0 GiB 8300 rootfs
7 4257792 14940159 5.1 GiB 8300
```
You can fix that by loading into `initramfs-kernel`, deleting empty `mmcblck0p7` partition and resizing `mmcblck0p6`
```
sysupgrade -F /tmp/openwrt-initramfs-kernel.bin
```
Install and run cfdisk
```
opkg update && opkg install cfdisk
cfdisk /dev/mmcblck0
```
- Select `mmcblck0p7` -> Delete
- Select `mmcblck0p6` -> Resize -> Write -> yes -> Quit
You will not see any difference in `cat /proc/partitions` after that but just flash a `sysupgrade` and you'll get the whole 7.3GB space for the `/overlay`.
Co-developed-by: hecatae <horus.ra@gmail.com>
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18220
(cherry picked from commit 99ea96c297)
Link: https://github.com/openwrt/openwrt/pull/18434
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This PR adds support for netis NX31 router.
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM : 256 MiB DDR3
- Flash : SPI-NAND 128 MiB (ESMT)
- WLAN : MediaTek MT7976CN dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x3 (LAN, MediaTek MT7531AE)
10/100/1000 Mbps x1 (WAN, SoC internal phy)
- USB : No
- Buttons : Mesh, Reset
- LEDs : 1x Power (blue), unmanaged
1x Status (blue), gpio-controlled
1x WiFi 2.4 GHz (blue), gpio-controlled
1x WiFi 5 GHz (blue), gpio-controlled
3x LAN activity (blue), switch-controlled
1x WAN activity (blue), gpio-controlled
- Power : 12 VDC, 1 A
Installation
------------
1. Connect to the router using ssh (user: admin, pass: web interface
password)
2. Make mtd backup:
cat /dev/mtd0 | gzip -1 -c > /tmp/mtd0_spi0.0.bin.gz
cat /dev/mtd1 | gzip -1 -c > /tmp/mtd1_BL2.bin.gz
cat /dev/mtd2 | gzip -1 -c > /tmp/mtd2_u-boot-env.bin.gz
cat /dev/mtd3 | gzip -1 -c > /tmp/mtd3_Factory.bin.gz
cat /dev/mtd4 | gzip -1 -c > /tmp/mtd4_FIP.bin.gz
cat /dev/mtd5 | gzip -1 -c > /tmp/mtd5_ubi.bin.gz
3. Download mtd backup from the /tmp dir of the router to your PC using
scp protocol
4. Upload OpenWrt 'bl31-uboot.fip', 'preloader.bin' images to the /tmp
dir of the router using scp protocol
5. Write FIP and BL2 (replace bootloader):
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-bl31-uboot.fip FIP
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-preloader.bin BL2
6. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
7. Erase 'ubi' partition and reboot the router:
mtd erase ubi
reboot
8. U-Boot automatically boot OpenWrt recovery image from tftp server to
the RAM
9. Upload OpenWrt 'sysupgrade.itb' image to the /tmp dir of the router
(IP: 192.168.1.1) using scp protocol
10. Connect to the router using ssh and run:
sysupgrade -n openwrt-mediatek-filogic-netis_nx31-squashfs-sysupgrade.itb
Return to stock
---------------
1. Unpack stock BL2 and FIP partitions backup
2. Upload stock BL2 and FIP partitions backup to the /tmp dir of the
router using scp protocol
3. Connect to the router using ssh and run:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd unlock FIP
4. Restore backup:
mtd write /tmp/mtd4_FIP.bin FIP
mtd write /tmp/mtd1_BL2.bin BL2
5. Erase ubi and reboot:
mtd erase ubi
reboot
6. Power off the router
7. Press Reset button and power on the router. Release the button after
~10 sec
8. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware
Recovery
--------
1. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
2. Press “Reset” button and power on the router. After ~10 sec release
the button.
3. Use OpenWrt initramfs system for recovery
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | dc:xx:xx:d1:xx:18 | label |
| WAN | dc:xx:xx:d1:xx:1a | label+2 |
| WLAN 2g | de:xx:xx:11:xx:19 | |
| WLAN 5g | de:xx:xx:71:xx:19 | |
+---------+-------------------+-----------+
The LAN MAC was found in 'Factory', 0x1fef20
The WAN MAC was found in 'Factory', 0x1fef26
The WLAN 2g/5g MAC prototype was found in 'Factory', 0x4
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18324
(cherry picked from commit d8002cb627)
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18438
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adds latest 6.6 patches from the Raspberry Pi repository.
These patches were generated from:
https://github.com/raspberrypi/linux/commits/rpi-6.6.y/
With the following command:
git format-patch -N v6.6.85..HEAD
(HEAD -> bba53a117a4a5c29da892962332ff1605990e17a)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 4618d09587)
Adds support for setting bridge port learning and isolation flags on
ipq40xx.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/18375
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit af93874f4e)
Bridge port isolation offload support has been added to the bridge core
and many DSA drivers. mt7530 support was backported in OpenWrt commit
c4e6a147a6 ("generic: 6.6: mt7530: add support for bridge port
isolation").
Backport qca8k support as well.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/18375
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 5d1dedd9f7)
Currently, network ports using PHYs get a link, but there is no traffic.
Make it work again by moving the MAC config to phylink_mac_link_up.
A similiar change has been previously applied for RTL83xx in commit
cd958d945b ("realtek: 6.6: refactor mac config and link up for
RTL83xx").
Fixes: https://github.com/openwrt/openwrt/issues/17010
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18268
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit a7e1e13817)
Specifications:
- SoC: Broadcom BCM63168 dual 400MHz MIPS
- Flash: 128MB NAND ESMT F59L1G81A
- RAM: 128MB DDR3
- Ethernet: 5x 1000M
- Wifi: BCM435F
- 1x USB 2.0 port
- 2x Button
- 11x LED
- Coax HPNA (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
The booloader will only install signed firmware so the image has to
be manually flashed.
- Set up a TFTP server on 192.168.1.0/24 to serve the initramfs image
- Interrupt the bootloader and run from RAM with
r 192.168.1.100:openwrt-bmips-bcm63268-actiontec_t1200h-initramfs.elf
- On the openwrt console, copy the wfi image using wget/tftp/scp, i.e
scp user@192.168.1.100:~/openwrt/bin/targets/bmips/bcm63268/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin /tmp/
- Erase half the flash partition where openwrt will be installed with
flash_erase -j /dev/mtd1 0 491
- Flash the openwrt image with
nandwrite -p /dev/mtd1 /tmp/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin
- Reboot
- Interrupt the bootloader again and use the c command to boot from
previous firmware if vendor image is loaded
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[Minor improvements to DTS file]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 65b8a978de)
