This fixes a failed bring up of the radio on bootup
if the model defines a rename of phy in its /etc/board.json.
This specifically impacts Redmi AX6S and any router that does so
in its /etc/board.json. The fix fortunately is simple, just update
phy name in phys after rename.
The entry that specifically causes this issue is the following:
{
<omitted>
"wlan": {
"wl0": {
"path": "platform/18000000.wmac",
"info": {
"antenna_rx": 15,
"antenna_tx": 15,
"bands": {
"2G": {
"ht": true,
"max_width": 40,
"modes": [
"NOHT",
"HT20",
"HT40"
],
"default_channel": 1
}
},
"radios": [
]
}
},
...
}
The issue is that after rename, referenced phy in config is going to be
wl0 but in phys array it is still phy0; and so it fails to find phy
and does not bring up radio.
Fixes: https://github.com/openwrt/openwrt/issues/20250
Fixes: https://github.com/openwrt/openwrt/issues/20339
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/21175
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit e4d5e76af0)
This is a trivial change to allow users to use 'list' on iface.
Old wifi-scripts already implements this, so this just ensures
that shell-based and ucode wifi-scripts are on-par with each other.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/20977
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 1ead4e6e16)
When iface is omitted, wifi-vlan will apply to all interfaces.
However, netifd.set_vlan call is not successful as it assumes
that every wifi-vlan section corresponds to one VIF.
For this reason in the wifi-vlan case (cur_type == "vlan")
we create a composite key in the form `${vif.name}/${vlan.name}`
allowing the same vlan section to correspond to multiple VAPs.
`/` was decided as a delimiter as it is an invalid character
for a network interface name and UCI identifier; so it is
impossible for it to cause conflicts.
It was verified that the `ubus call network.wireless status`
works as expected with this change. Moreover, wifi-station
is not susceptible to this problem.
This also means that it is now possible for wifi-vlan
to support `list` iface similar to old shell-based wifi-scripts.
This will be done in a follow-up commit.
Fixes: 98435a37a7 ("wifi-scripts: iface should be optional in wifi-vlan definition")
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/20977
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 211b11a56e)
This adds support for beacon_prot and spp_amsdu in hostapd and
beacon_prot in wpa_supplicant (spp_amsdu is not relevant there).
Both options are disabled by default unless set in the config.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/20793
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In the past PR[1] to add SAE wifi-station support, a commenter[2] requested
that the mac option be changed into a list. After trying to migrate my old
RADIUS setup I found myself wanting this change as well as it would simplify
my config. This patch does precisely that. Old configs that specify
`option mac ....` still work without any issues.
This change was done for both PSK and SAE. The schema was updated as well.
[1]: https://github.com/openwrt/openwrt/pull/17145
[2]: https://github.com/openwrt/openwrt/pull/17145#issuecomment-2523507953
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/17650
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is useful as there are cases where no network is configured
or the configured network is isolated (APs are blocked from
communicating with each other over it). In both cases, it would make
sense to set ft_iface to another interface dedicated to FT over DS
traffic.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/20797
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adds missing default value for na_mcast_to_ucast when proxy_arp is not enabled
in order to silence the following msg:
daemon.notice: netifd: radio1 (xxxx): sh: out of range
Fixes: bcdb29f78f ("wifi-scripts: add na_mcast_to_ucast option")
Reported-by: Antony Kolitsos <zeusomighty@hotmail.com>
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/20806
Signed-off-by: Robert Marko <robimarko@gmail.com>
Similar to "wifi-scripts: iface should be optional in wifi-vlan definition"
(98435a3), wifi-station iface should also be optional. By default, it is
supposed to match all interfaces if omitted.
Fixes: https://github.com/openwrt/openwrt/issues/20705
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/20694
Signed-off-by: Robert Marko <robimarko@gmail.com>
Most users on forums face a broken 802.11r setup when having
a very simple 802.11r config (i.e., just ieee80211r enabled).
In most cases, simply bumping reassociation_deadline to
20000 fixes their problems and allows 802.11r to just work.
Reassociation Deadline is already set to 20 seconds on Cisco
equipment by default[1] which is why this value has been
chosen.
It is also mentioned on the OpenWRT Wiki as a value that should
be changed in order for 802.11r to work on Apple devices. I think
it would be better to change the defaults instead so users don't
have to do much work for a working setup.
[1]: https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/80211r-ft/b-80211r-dg.html
Fixes: https://github.com/openwrt/openwrt/issues/7907
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/20799
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is useful to alter the default ban time after an STA
association is rejected for being below RSSI threshold.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/20811
Signed-off-by: Robert Marko <robimarko@gmail.com>
When an MLO interface specifies multiple radios and the first radio
is disabled, the MLO configuration was never created because the code
only attempted to create it when processing the first device in the
list (which gets skipped if disabled).
Fix by creating the MLO config for the first enabled device instead
of only when processing dev_names[0].
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ensure that the 4addr flag is passed to phy.wdev_add.
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is useful if multiple passwords were specified without
the use of a SAE password identifier. This is the only
way to get multiple passwords for a single peer to work
without resorting to password identifiers.
Unfortunately, support for password identifiers is non-existent
on Android and macOS; and possibly others. So this is the only
option in that case.
As an alternative, one could also continue to use WPA2-PSK instead
as that could easily resort to a bruteforce approach without any
complications.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/20597
Signed-off-by: Robert Marko <robimarko@gmail.com>
As this is generally only useful with "proxy_arp" enabled,
we default na_mcast_to_ucast to true if "proxy_arp" is already
enabled.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/20596
Signed-off-by: Robert Marko <robimarko@gmail.com>
When a phy appears after setup has already been attempted, tell netifd
to retry setup for all failed wireless devices.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This can be used by other services to trigger reconfiguration, or detect when
PHY renaming has been performed.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ensures that renaming is handled properly. For disabled radios, setup is
performed with an empty list of interfaces.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There are no supported drivers where it even makes sense to disable WMM
anymore, since so much depends on it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Can also be used for a client mode interface that is able to connect on
multiple bands individually, while handling hostapd state for the correct
band.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mlo specific hostapd ubus call from wireless handler to netifd core
ucode script. This avoids unnecessary queueing and the fake MLO wireless
device.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When a wifi-iface section is used either for multiple vifs or MLD links,
make it possible to configure the per-radio/link macaddr.
When MLO is enabled, the main macaddr is used for the MLD interface.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Initialize data to {} if null before calling mac80211.sh
to avoid a confusing error message in the syslog.
Fixes: https://github.com/openwrt/openwrt/issues/14010
Signed-off-by: Tobias Waldvogel <tobias.waldvogel@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cosmetic change]
The option iface should be optional according to the description
of /etc/config/wireless in order to avoid repeating the definition
for each virtual interface.
Signed-off-by: Tobias Waldvogel <tobias.waldvogel@gmail.com>
Execute scripts in /etc/rc.wps until one of them returns a exit code of 0.
Split up sta and ap handling of wps into separate scripts.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unless HE/EHT is enabled, the client should not process the RSN override IE.
This prevents picking up unsupported ciphers
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Allow toggling autostart even for disabled devices
When switching from enabled to disabled, call teardown instead of setup
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MLO can be enabled by configuring a wifi-iface section with multiple
radios, like this:
config wifi-iface
list radio 'radio0'
list radio 'radio1'
option mlo '1'
option ssid 'OpenWrt'
option mode 'ap'
option network 'lan'
...
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MLO interface config is provided in a separate ubus call before
adding regular per-phy interfaces.
Preparation for full MLO support.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
3a7878065829 system-dummy: add missing vrf functions
471d9d6abb6d CMakeLists.txt: bump minimum required version
c3a0255e2150 scripts: fix dummy mode on systems where libubox is in /usr/local
7a3b281230e4 update example mac80211 script and wireless config
d9f2dd2614f2 wireless: replace with ucode scripts
74c22601baad wireless: add MLO support to example scripts
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Correctly load the list of basic_rates from UCI. basic-rates shall be
stored as a option-list. The current code did not retrieve this list
correctly.
wpa_supplicant uses a different config option to set basic-rates
when operating in mesh-mode.
Use the correct config key and calculation for mesh-interfaces.
Signed-off-by: David Bauer <mail@david-bauer.net>
Override via RSNE is a relatively new feature, which can be used to enable
WPA3 features in a way that is invisible to older clients.
Use it by default to mask the GCMP-256 cipher from older clients, since
there are compatibility issues with existing devices.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some ath12k radios can take long time to initialize and register a
phy. This can cause netifd to fail to detect them during initial scan.
To address this issue, a hotplug script has been added to retry
configuration once they have registered their phy.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
For WIFI7 devices (such as mt7925e), the dev width is currently
always "20 MHz (no HT)" in monitor mode.
Add EHT and HE160 support to iw_htmode to fix this issue.
Additionally, the following changes are made:
1. Set iw_htmode to 160MHz for VHT160. The reason for the current
VHT160 setting is unclear and seems to have been in place for
over a decade (ibss_htmode [1]). If anyone knows its impact,
please inform me so I can restore it.
2. Modify MHZ to MHz. The original matching table in the current
iw tool uses MHz. Although the match is case-insensitive,
correcting this won't hurt.
[1]: 768d09be87
Signed-off-by: Ming Kuang <ming@imkuang.com>
Link: https://github.com/openwrt/openwrt/pull/18319
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
he_spr_psr_enabled is appended to hostapd.conf if it's enabled, but hostapd
doesn't support this config, it should be used as an internal flag to control
the he_spr_sr_control configuring.
Signed-off-by: Lix Zhou <xeontz@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18025
Signed-off-by: John Crispin <john@phrozen.org>
The 00 address_mask needs to be inverted, otherwise the mac address
allocation will modify the last byte instead of the first one.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Bringing up a mesh interface using wpa_supplicant already supports a
per-VIF basic rate selection. Add the same ability when creating a mesh
VIF without wpa_supplicant.
Signed-off-by: David Bauer <mail@david-bauer.net>
