Add uboot-envtools support for Gateworks venice boards based on i.MX8M
SoC's (imx_cortexa53) which boot from and store their U-Boot env on
eMMC boot0 hardware partition.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19347
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Force update_cache_variantsvariants to use reset for Foresee NAND with bad blocks.
Tested on Xiaomi AX3000T + F35SQA001G with bad blocks and without bad blocks
Signed-off-by: Dim Fish <dimfish@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17963
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The same function is used twice, so let's make it common.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18818
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Functions ubootenv_add_mtd, ubootenv_add_sys_mtd and ubootenv_add_mmc
can be shared so make them common.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18818
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, uboot-envtools is being built for a (shared) instruction
set (phase2 in buildbots) instead of target-specific (phase1 in builbots).
So the package does not contain the uci-defaults file specific for each
target_subtarget. (Only the fortunate target with coincidentally the same
instruction set and target as the SDK chosen by the buildbot will have the
uci-defaults file.)
This commit sets the nonshared flag correctly in the Makefile so that
uboot-envtools is built for the target-specific (phase 1).
This is done by using the PKGFLAGS variable which is intended for
per-binary flags (instead of PKG_FLAGS which has a global scope), as
stated in some old commits 349e7b635e[1], 2d7eaf2e15[2], 064e7c8f00[3] and
2cb75cd8b9[4].
While at here, use PKG_URL, instead of URL, which is intended for global
scope. As stated in commit e32edf712b[5].
[1] 349e7b635e
[2] 2d7eaf2e15
[3] 064e7c8f00
[4] 2cb75cd8b9
[5] e32edf712bFixes: #19040
Fixes: 46e376c ("uboot-tools: migrate uboot-envtools to uboot-tools")
Signed-off-by: Mario Andrés Pérez <mapb_@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19180
Signed-off-by: Robert Marko <robimarko@gmail.com>
The IgniteNet SunSpot AC Wave2 uses the standard smem-assigned partition
for its bootloader environment.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The qcomsmem MTD partition parser converts all partition names to
lower case while the vendor solution uses upper case names, which
often made their way into OpenWrt as labels in 'fixed-partitions'
(probably due to contributors and reviewers being unaware of the
qcomsmem parsers).
Use case-insensitive matching of the 'APPSBLENV' name to make
ubootenv_mtdinfo() work in both cases.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for Check Point V-81 to add/edit bootcmd variables for
booting OpenWrt.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16904
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for Check Point V-80 to add/edit bootcmd variables for
booting OpenWrt.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16904
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This file is a leftover of cns3xxx target which has been dropped
in commit a9790dff53 ("cns3xxx: drop target").
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19191
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for Xiaomi AX6000.
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Etrontech EM6HE16EWAKG 512 MiB DDR3L-933
* Serial Port: 1v8 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax - up to 574 Mbps)
QCN9024 (4x4 5 Ghz 802.11an/ac/ax - up to 4804 Mbps)
QCA9887 (1x1 5 Ghz 802.11ac/n - up to 433 Mbps)
* Ethernet: IPQ5018 integrated virtual switch connected to:
- external QCA8337 switch (3 LAN Ports 10/100/1000)
- QCA8081 Phy WAN port (10/100/1000/2500)
* Flash: Either of:
- Gigadevice GD5F1GQ4RE9IGD (128 MiB)
- ESMT F50D1G41LB (128 MiB)
* LEDs: 1x WLAN Link (GPIO 23 Active High)
1x System Blue (GPIO 24 Active High)
1x System Yellow (GPIO 25 Active High)
1x WAN Link Blue (GPIO 26 Active High)
1x WAN Link Yellow (GPIO 27 Active High)
1x Green - Unused(GPIO 28 Active High)
3x LAN Phy Green
1x WAN Phy Green
* Buttons: 1x Reset (GPIO 38 Active Low)
Known issue:
- QCA9887 doesn't come up (possibly due to 1-lane PCIe phy not coming up or missing method to drive power),
hence the host PCIe controller is disabled in the DTS.
Flash instructions:
Download XMIR Patcher: https://github.com/openwrt-xiaomi/xmir-patcher
First flash a ubinized OpenWrt initramfs that will serve as the intermediate step, since
OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for
packages, through either of the below two methods:
Installation via XMIR Patcher:
1. Load the initramfs image: openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi
Installation via ubiformat method, through SSH:
1. If needed, enable SSH using XMIR Patcher.
2. Copy the file openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi to the /tmp directory
3. Open an SSH shell to the router
4. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
5. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd18 and mtd19 are the correct indexes from above!
6. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
7. Reboot the device by:
reboot
Continue in order to pernamently flash OpenWrt:
1. Upload the sysupgrade image to /tmp/ using SCP:
scp -O <path to image> root@192.168.1.1:/tmp/
2. Open an SSH shell to 192.168.1.1 from a PC within the same subnet
3. Use sysupgrade to flash the sysupgrade image:
sysupgrade -n -v /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for I-O DATA WN-DAX3000GR to update bootdelay variable while
sysupgrade.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19053
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add an additional bootmenu option and commands to overwrite the GPT
table with the custom one for upstream U-Boot.
This is needed as the pre-installed GPT table differ and updating the
GPT table is a requirement to install the upstream U-Boot (or the old
U-Boot will be loaded)
To make the migration to new U-Boot bootloader an user can now load the
system with mtk_uartboot and select "Load GPT Table ..." in conjunction
with other update command.
Link: https://github.com/openwrt/openwrt/pull/18874
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace bootmenu shortmenu mediatek patch with a better version proposed
upstream that implement a more clean implementation.
Also the mediatek patch seems to be bugged and with lots of bootmenu
elements it's gets very bugged and unusable.
Refresh any affected patch.
Upstream-Status: Submitted [https://lore.kernel.org/u-boot/20250525134407.3760-1-ansuelsmth@gmail.com/]
Link: https://github.com/openwrt/openwrt/pull/18919
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This allows us to use the full size of nand, which increases ubi size
from 64M to 122.25M.
If you are at factory firmware, please refer commit 63b8d98dd0 ("mediatek: add support for Cudy TR3000 v1")
to boot into OpenWrt initramfs (stock layout).
Flash instructions:
1. Login into the device and backup everything, especially 'Factory' part.
1. Unlock mtd partitions:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
3. Write new BL2 and FIP
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Tested-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
SOC: MediaTek MT7981b
RAM: 256MB DDR3
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7981b DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Interface MAC Algorithm
LAN 8C:AE:DB:2C:xx:xx label
WAN 8C:AE:DB:2C:xx:xx label +1
WLAN 2.4G 8C:AE:DB:2C:xx:xx label +2
WLAN 5G 8C:AE:DB:2C:xx:xx label +3
Installation
-------------------Install openwrt image-------------------------------:
Set a static ip on the ethernet interface of your PC. (ip address:
192.168.1.254, subnet mask:255.255.255.0) .
Download the OpenWrt uboot image
(openwrt-mediatek-filogic-snr_cpe-ax2-bl31-uboot.fip).
SSH/SCP opened by default on the stock firmware (3.0.1).
Username: Admin, default password: Admin. Check it on the bottom of
the router.
Copy uboot image using SCP (WinSCP) to /tmp dir on SNR-CPE-AX2.
Download recovery file.
openwrt-mediatek-filogic-snr_snr-cpe-ax2-initramfs-recovery.itb.
Copy the recovery image to a TFTP server reachable at 192.168.1.254/24.
Open ssh shell to the SNR-CPE-AX2.
Run commands:
mtd write \
/tmp/openwrt-mediatek-filogic-snr_snr-cpe-ax2-bl31-uboot.fip FIP
reboot
Wait until recovery boot.
Open web 192.168.1.1 and do sysupgrade by
openwrt-mediatek-filogic-snr_cpe-ax2-squashfs-sysupgrade.itb
Signed-off-by: Nikolay March <palladin82@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/18700
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
A lot of warnings were treated as errors after the default compiler
switched to GCC14. It's hard to fix them one by one, and this u-boot
is not maintained by upstream, so let's just silence these warnings.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18833
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This U-Boot version is used to generate a 'reference'
U-Boot binary for QEMU's 'virt' machine on both
armv7 and armv8.
It has not been updated since EFI support was merged
into the then-armvirt target, so we should bring it up
to the latest version.
The 'mkeficapsule' tool is disabled due to a host-side
dependency on GnuTLS.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Link: https://github.com/openwrt/openwrt/pull/18862
Signed-off-by: Robert Marko <robimarko@gmail.com>
TP-Link EAP625-Outdoor HD is a 802.11ax AP claiming AX1800 support.
It is wall or pole mountable, and rated for outdoor use. It can only
be powered via PoE.
Hardware-wise, it is very similar to the older EAP610-Outdoor model.
Software-wise, I couldn't find a difference other than the board
data files, and device name. For this reason, the majority of the
devicetree from the EAP610-Outdoor is reused.
This device currently comes in a "v1", and "v1.6" version. The
"support-list" of the vendor firmware does not have a distinction
between these versions. This commit was tested on a 'V1.6" device.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512 MB
* Storage: 128MB NAND
* Ethernet:
* Gigabit RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Multi-color System LED (Green/Amber)
* Buttons:
* 1x Reset
* UART: 4-pin unpopulated header
* 1.8 V level, Pinout 1 - TX, 2 - RX, 3 - GND, 4 - 1.8V
Installation:
=============
Web UI method
-------------
Set up the device using the vendor's web UI. After that go to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
The connect to the machine via SSH:
ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
Disable signature verification:
cliclientd stopcs
Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
* Go to System -> Firmware Update.
* Under "New Firmware File", click "Browse" and select the image
* Select "Update" and confirm by clicking "OK".
If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWRT.
NOTE: If ssh continues to complain that "no matching host key type
found. Their offer: ssh-rsa,ssh-dss" it likely means that yor distro
has completely disabled deprecated siphers in ssh. In that case, run
the ssh command from a docker container of an older distro.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot tplink_eap625-outdoor-hd-v1-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the commandline.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18584
Signed-off-by: Robert Marko <robimarko@gmail.com>
This fixes the following compile problem:
```
arv7506pw11.c: In function 'show_boot_progress':
arv7506pw11.c:59:24: error: 'return' with a value, in function returning void [-Wreturn-mismatch]
59 | return 0;
| ^
arv7506pw11.c:56:6: note: declared here
56 | void show_boot_progress(int arg)
| ^~~~~~~~~~~~~~~~~~
arv7506pw11.c:71:16: error: 'return' with a value, in function returning void [-Wreturn-mismatch]
71 | return 0;
| ^
arv7506pw11.c:56:6: note: declared here
56 | void show_boot_progress(int arg)
| ^~~~~~~~~~~~~~~~~~
```
Link: https://github.com/openwrt/openwrt/pull/18688
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
A patch was added upstream to temporary enable RTC clock configuration only
for STM32MP15 boards. Use this patch instead of reverting commit 03a581e2.
Now for STM32MP135 boards RTC clock configuration is handled by optee-os.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18628
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
YAFFS support in U-Boot is basically abandoned and will even fail to
build with GCC14, so simply disable it.
Link: https://github.com/openwrt/openwrt/pull/18598
Signed-off-by: Robert Marko <robimarko@gmail.com>
uImage.FIT validation was restricted to certain sub-image types
which is problematic as it then won't validate eg. 'filesystem' type
subimages. Also prevent decompressing sub-images into a arbitrary
sized buffer just to then free that buffer -- there is not need to
do this and creating malicious compressed payloads which overflow the
buffer is too easy.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for ELECOM WRC-X3000GS2 to update "bootdelay" variable
configured as "0" by default when sysupgrade.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18543
Signed-off-by: Robert Marko <robimarko@gmail.com>
Changes: https://github.com/u-boot/u-boot/compare/v2025.01...v2025.04
Drop patch 100-rockchip-add-FriendlyElec-NanoPi-R3S.patch. U-Boot
upstream now supports this board.
Tested on Radxa ROCK 5B+.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The TP-link Deco X80-5G is a AX WIFI router with a single 1G (LAN) and 1 2.5G (WAN) port with a built in Quectel 5G modem.
Specifications:
Architecture ARMv8-A (aarch64 Cortex A53, 4 cores)
Vendor Qualcomm
Bootloader U-Boot (2016)
System-On-Chip Qualcomm IPQ8074A (Networking Pro 1210 platform)
CPU/Speed 2.2GHZ
Flash-Chip ESMT F59D1G81MB-45TI 1G-bit NAND
Flash MB 128MB (1Gbit)
RAM-chip 2* ESMT M15T4G16256A-DEBG2G 2Gb DDR3L (32bit)
RAM MB 512MB (4Gbit)
WLan System-On-Chip (5g) Qualcomm QCN5054
WLan Front end modules (5g) 8* Qorvo QPF4588
WLAN (5G) A/N/AC/AX
WLAN Antenna (int) 8* (4 shared with 2.5G)
WLan System-On-Chip (2.4G) Qualcomm QCN5024
WLan Front end modules (2.4G) 4* Skyworks SKY85340-11
WLAN (2.4G) B/G/N/AX
WLAN Antenna (int) 4* (shared with 5g)
Eithernet-phy (1Gbit) Qualcomm (Atheros) AR8033-AL1A
Ethernet (1Gbit) 1*
Eithernet-phy (2.5Gbit) Qualcomm QCA8081
Ethernet (2.5Gbit) 1*
Switch Embedded in the SOC?
Serial 1.8v 8n1 (testpoints)
Modem System-On-Chip Qualcomm 5G RG50xQ (Snapdragon X55 platform)
5G modem capability 5000Mbps down 900Mbps up
5G modem bands N1/N3/N5/N7/N8/N20/N28/N38/N40/N41/N77/N78/N79
4G modem capability 4.5G LTE-Advanced Pro (Cat20 down 2Gbps) (Cat18 up 200Mbps)
4G modem FDD bands B1/B3/B5/B7/B8/B18/B19/B20/B26/B28
4G modem TDD bands B34/B38/B39/B40/B41/B42/B43
Modem antenna (int) 8* (5G/4G use)
Modem antenna (ext) 2* SMA connectors (5G/4G use)
SIM type 1* Nano SIM
Telephony 1* POTS RJ11
(see wiki for more info:)
https://openwrt.org/inbox/toh/tp-link/x80-5g_v1
Notes:
Installation Instructions:
Between antennas 7 and 8 on the PCB with the RGB harness there are three test pads labelled TP1 TP2 and TP3 connections are as follows:
|TP2|-- RX
|TP1|-- TX
|TP3|-- GND
RX requires an external pullup to operate somewhere around 5 K ohm but your luck may vary the Uart is 1.8v
Set a static IP and set up a tftpserver and terminal.
power the router and quickly type the magic string “tpl” and press enter to break into u-boot
in the shell set the environment variables to enable tftp booting
setenv ipaddr (routerIP)
setenv serverip (server IP)
load you initramfs:
tftpboot 0x44000000 (serverIP):openwrt-qualcommax-ipq807x-tplink_x80-5g-initramfs-uImage.itb
boot your initramfs
bootm
upload your factory image to /tmp
format and install the factory image:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-qualcommax-ipq807x-tplink_x80-5g-squashfs-factory.ubi
Note as this device swaps root partitions upon update your boot partition may be set as mtd13
Update script to mount factory tplink partition's for MAC recovery and device data.
Capture Labelmac from Factory_data partition.
Patch LAN from Labelmac.
Patch ART from Labelmac.
Set GPIO to make modem operational from boot.
GPIO fan tables work like the stock device with three fan maps high active idle with a top fan speed of 6800 RPM.
High temp 70 deg speeds 6-8
Active temp 50 deg speeds 2-5
low temp 25 degree speed 0-1
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/16329
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Xiaomi MiWiFi 3A wireless router has a similar system architecture as the Xiaomi Mi 4A router, which is already officially supported by OpenWrt.
Product website: https://www.mi.com/miwifi3a
Device specification
--------------------
SoC: MT7628AN MIPS_24KEc @ 580 MHz 2.4G-bgn 2x2
WiFi: MT7612EN 5G-an, ac 80 MHz 2T2R
Flash: 16 MB
DRAM: 64 MB
Switch: MT7628AN (integrated in SoC)
Ethernet: 1 x 10 /100 Mbps
USB: None
Antennas: 2 x 2,4 GHz and 2 x 5 GHz (all are external and non-detachable)
LEDs: blue/red/amber
Buttons: Reset
Serial: 115200,8n1
MAC addresses as verified by OEM firmware:
------------------------------------------
use address source
LAN *:DD factory 0x28
WAN *:DD factory 0x28
2g *:DE factory 0x4
5g *:DF factory 0x8004
OEM firmware uses VLAN's to create the network interface for WAN and LAN.
Bootloader info:
----------------
The stock bootloader uses a "Dual ROM Partition System".
OS1 is a deep copy of OS2.
The bootloader starts OS2 by default.
To force start OS1 it is needed to set "flag_try_sys2_failed=1".
How to install:
---------------
1- Use OpenWRTInvasion to gain Telnet, SSH and FTP access: https://github.com/acecilia/OpenWRTInvasion
[IP: 192.168.31.1 | Username: root | Password: root | FTP-Port: 21]
2- Connect to router using telnet or ssh.
3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0". Copy /tmp/mtd0 to computer using ftp.
4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3a-squashfs-sysupgrade.bin to /tmp in router using ftp.
5- Enable UART access and change start image to OS1.
nvram set uart_en=1
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set flag_try_sys2_failed=1
nvram commit
6- Erase OS1 & OS2 and install OpenWrt
mtd erase OS1
mtd erase OS2
mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3a-squashfs-sysupgrade.bin OS1
Credits:
--------
This PR is based on the work of Zehao Zhang (Github: @ZZH-Finalize) that he had published in the PR: #15698
Signed-off-by: Olgun Demir <olgun.demir@mail.com.tr>
Link: https://github.com/openwrt/openwrt/pull/18427
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for GL.iNET (AX3000) B3000.
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Winbond W634GU6NQB-11 (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
* Wi-Fi: QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (3 Ports 10/100/1000 GBASE-T)
* Flash: Winbond W25N01GWZEIG (128 MiB)
* LEDs: 1x single-color blue LED (GPIO 24 Active High)
1x single-color white LED (GPIO 23 Active High)
* Buttons: 1x Reset (GPIO 27 Active Low)
Flash Instructions:
*** The .img files are now universal ! ***
Openwrt --> openwrt-qualcommax-ipq50xx-glinet_gl-b3000-squashfs-factory.img
GL.iNet OEM --> openwrt-b3000-4.5.18-0731-1722397535.img
Either file can be flashed, in any of the available upgrade options, in both Firmwares.
Pick a file .. pick a method .. and SEND IT !!
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17903
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add entry for STM32MP157C-DK2 and the SCMI variant.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18119
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add entry for STM32MP157C-DK2 and the SCMI variant.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18119
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add entry for STM32MP157C-DK2 and the SCMI variant.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18119
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
During envtools conversion to the generic uboot-tools package, a syncconfig
call was added to the configure step which was previously not there.
We received multiple spourious reports that now envtools were failing to
build [1], but it was not reproducible.
However, it seems that this could easily be reproduced on MacOS 15 and
somehow that syncconfig call is breaking build by Makefile.autoconf not
being executed and thus no "include/config.h" is generated.
So, since this call was not previously there and U-Boot will actually do
syncconfig on its own when needed lets drop it.
[1] 293d5f1366 (commitcomment-154347516)
Link: https://github.com/openwrt/openwrt/pull/18515
Signed-off-by: Robert Marko <robimarko@gmail.com>
Look for OPENWRT_VERBOSE and pass it down to the U-Boot so we actually
get verbose build info when needed for debugging.
Link: https://github.com/openwrt/openwrt/pull/18515
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update uboot-ath79 package to v2025.04 for ath79 devices.
Additionally, new "CONFIG_NO_NET" option was introduced and replaced
disabled CONFIG_NET option ("# CONFIG_NET is not set"). So replace
that old options in the NEC Aterm devices as well.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18475
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, tfa-layerscape packages are being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in:
377b66990b ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~trusted-firmware-a-ls1012a-frdm' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the individual TFA packages in DEVICE_PACKAGES we can just
do what other targets do and set BUILD_DEVICES so that TFA packages are
automatically set.
Fixes: #18412
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
