This is the recommended way for the OF based platform.
Tested-on TP-Link TL-WR2543N with RTL8367 switch:
```
root@OpenWrt:~# dmesg |grep -i rtl
[ 7.941126] rtl8367 rtl8367: cannot find mdio node phandle
[ 7.947562] rtl8367 rtl8367: RTL8367R ver. 0 chip found
[ 9.056830] rtl8367 rtl8367: cpu_port:9, assigned to extif0
root@OpenWrt:~# cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 512-529, parent: platform/18040000.gpio, 18040000.gpio:
gpio-512 ( |lime:status ) out lo ACTIVE LOW
gpio-513 ( |rtl836x-sda ) in hi
gpio-518 ( |rtl836x-sck ) in lo
gpio-520 ( |lime:usb ) out hi ACTIVE LOW
gpio-523 ( |reset ) in hi IRQ ACTIVE LOW
gpio-524 ( |wps ) in hi IRQ ACTIVE LOW
```
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21143
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
mdio node is optional for the rtl836x switch. Some devices use GPIO to
control the switch chip. Missing mdio is a normal behavior.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21143
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If the switch is directly controlled by the mdio bus, we must ensure
that the mdio bus is ready instead of trying GPIO simulated bus.
Fixes: d4ac26ec49 ("kernel: rtl8366-smi: add Realtek switch management via mii-bus")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21143
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There are no platform_data based devices using it anymore. Also move
header files to the driver folder.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21138
Signed-off-by: Robert Marko <robimarko@gmail.com>
Teaming is a link aggregation implementation similar to bonding, but
it's configured by a userspace program.
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21120
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add opending patch fixing resource_size(9 if resource start and end is
set to zero.
This is to indirectly fix a helper rework in ath11k qmi code that cause
firmware load panic.
Link: https://github.com/openwrt/openwrt/pull/20964
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move reserved_mem backports patch from airoha to generic dir as it will
be also used by backports package based on 6.18.
Link: https://github.com/openwrt/openwrt/pull/20964
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport support for faux base driver needed for backports package to
compile with kernel 6.18.
Link: https://github.com/openwrt/openwrt/pull/20964
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Unneeded semicolon
WARNING comparing pointer to 0
WARNING: NULL check before some freeing functions is not needed.
WARNING: casting value returned by memory allocation function to (u32 *)
ERROR: allocation function on line 378 returns NULL not ERR_PTR on failure
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19932
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport fix for premature SPI CS deassertion on RX-only transactions from
linux v6.18, which is needed for bmips (bcm63xx).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Backport support for the Quectel RG255C USB modem.
This modem is used, among others, on the Teltonika RUT976.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/20933
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since everything got migrated to the layouts driver, this is no longer
needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20948
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport of the latest upstream Realtek PHY patches. WoL uses
devm_pm_set_wake_irq(), so the patch that adds this function
has also been backported.
Changelog:
4465ae435ddc net: phy: realtek: create rtl8211f_config_phy_eee() helper
bb78b71faf60 net: phy: realtek: eliminate priv->phycr1 variable
e1a31c41bef6 net: phy: realtek: allow CLKOUT to be disabled on RTL8211F(D)(I)-VD-CG
910ac7bfb1af net: phy: realtek: eliminate has_phycr2 variable
27033d069177 net: phy: realtek: eliminate priv->phycr2 variable
8e982441ba60 net: phy: realtek: create rtl8211f_config_rgmii_delay()
b826bf795564 net: phy: realtek: fix RTL8211F wake-on-lan support
Tested on Netgear WAX206 with RTL8221B-VB-CG.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20987
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport upstream patch to add support for the ESMT F50L1G41LC flash
chip. It is used in multiple Cudy products manufactured starting
November 2025.
Link: https://github.com/openwrt/openwrt/pull/20962
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the missing symbol to fix build halt on aarch64 targets:
```
Contiguous PTE mappings for user memory (ARM64_CONTPTE) [Y/n/?] (NEW) make[7]: *** [scripts/kconfig/Makefile:85: syncconfig] Error 1
make[6]: *** [Makefile:686: syncconfig] Error 2
```
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20954
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patchset silences some noisy dts false warnings:
[ 0.616266] OF: Bad cell count for /spi@1100d000/flash@0/partitions
[ 0.622551] OF: Bad cell count for /spi@1100d000/flash@0/partitions
Closes: https://github.com/openwrt/openwrt/issues/14701
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20942
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop all kernel 6.6 patches, hacks, backports and configuration support,
and remove the CONFIG_LINUX_6_6 guarded conditional in filogic.mk.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/20943
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
These patches fix the remaining issues with BCM5325 switches and allow
dropping the default VLAN on Huawei HG556a.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Hardware
--------
SOC: MediaTek MT7981
RAM: 512MB DDR4
FLASH: 128MB SPI-NAND
WIFI: Mediatek MT7915 (integrated) 2x2 802.11ax 2.4 / 5 GHz
ETH: Mediatek MT7981 internal 1 GbE PHY
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect the TFTP server to the EAX17. Conect to the serial console,
interrupt the autoboot process by pressing '0' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ tftpboot openwrt.bin
$ bootm
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Signed-off-by: Jascha Sundaresan <flizarthanon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20354
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These patches have been accepted in netdev-next for linux v6.19.
2b3013ac0302 net: dsa: b53: add support for bcm63xx ARL entry format
300f78e8b6b7 net: dsa: b53: add support for 5389/5397/5398 ARL entry format
a7e73339ad46 net: dsa: b53: move ARL entry functions into ops struct
e0c476f325a8 net: dsa: b53: split reading search entry into their own functions
1716be6db04a net: dsa: b53: provide accessors for accessing ARL_SRCH_CTL
bf6e9d2ae1db net: dsa: b53: move writing ARL entries into their own functions
4a291fe72267 net: dsa: b53: move reading ARL entries into their own function
a6e4fd38bf2f net: dsa: b53: b53_arl_read{,25}(): use the entry for comparision
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
These patches have been accepted for linux v6.18.
e57723fe536f net: dsa: b53: properly bound ARL searches for < 4 ARL bin chips
674b34c4c770 net: dsa: b53: fix ageing time for BCM53101
89eb9a62aed7 net: dsa: b53: fix reserved register access in b53_fdb_dump()
61730ac10ba9 net: dsa: b53: mmap: Implement bcm63268 gphy power control
7f95f04fe190 net: dsa: b53: mmap: Add gphy port to phy info for bcm63268
5ac00023852d net: dsa: b53: mmap: Implement bcm63xx ephy power control
e8e13073dff7 net: dsa: b53: mmap: Add register layout for bcm6368
c251304ab021 net: dsa: b53: mmap: Add register layout for bcm6318
aed2aaa3c963 net: dsa: b53: mmap: Add syscon reference and register layout for bcm63268
fcf02a462fab net: dsa: b53: Define chip IDs for more bcm63xx SoCs
be7a79145d85 net: dsa: b53: Add phy_enable(), phy_disable() methods
762e7e174da9 net: dsa: tag_brcm: do not mark link local traffic as offloaded
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
A considerable amount of b53 patches has been backported to 6.12, so we
can rename and group the remaining ones.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
New linux version will check the return code of parser on subpartitions.
The only valid case for skipping a parser with an error is -ENOENT.
Change the relevant entry to -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit ade045084b.
Skipping parser for subpartition will be handled now with -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
New linux version will check the return code of parser on subpartitions.
The only valid case for skipping a parser with an error is -ENOENT.
Change the relevant entry to -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit a51359aafd.
Skipping parser for subpartition will be handled now with -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
New linux version will check the return code of parser on subpartitions.
The only valid case for skipping a parser with an error is -ENOENT.
Change the relevant entry to -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 6fa1775348.
Skipping parser for subpartition will be handled now with -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
New linux version will check the return code of parser on subpartitions.
The only valid case for skipping a parser with an error is -ENOENT.
Change the relevant entry to -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 5aab294726.
Skipping parser for subpartition will be handled now with -ENOENT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Rework each affected mtdsplit driver to make use of -ENOENT error
instead of -ENODEV to handle new kernel that checks error from parser on
subpartitions.
The only acceptable error is -ENOENT that skip the parser. This follow
pattern used upstream and also by an mtdsplit parser, mtdsplit_bcm_wfi,
and also by a workaround currently implemented for mtdsplit_mstc_boot.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 627a0e7da0.
A better solution has been accepted upstream that doesn't hide all
unexpected error.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport a trivial patch that half restore original functionality of MTD
parser for subpartition by ignoring if the parser returns -ENOENT.
This fix parsing and booting of some brcm devices.
Link: https://github.com/openwrt/openwrt/pull/20822
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Use skb->encapsulation flag instead of skb_tnl_header_len() to detect
encapsulated packets. Prevents false positives on non-encapsulated packets.
Reported-by: Mason-cw Chang (張哲維) <Mason-cw.Chang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
