Following up with errors reported in the ASU repo, these bananapi cases
do not match the DT compatible "bpi", sync with dts sources.
Also some profiles were overwriting SUPPORTED_DEVICES.
Sysupgrade would be failing in SUPPORTED_DEVICES check since
the DT compatible(/tmp/sysinfo/board_name) is not in SUPPORTED_DEVICES.
This should also fix errors when using ASU sysupgrade clients.
- Sync profile makefile target names with DT compatibles.
- Fix overwrites of SUPPORTED_DEVICES instead of appending.
- Adapt the uboot-sunxi profiles accordingly.
*bpi-p2-zero dts is still not upstream.
V2:
- Include fixes for arm926ejs(ARM926EJ-S) subtarget (LicheePi Nano and
PopStick v1.1) (profile rename for correct default SUPPORTED_DEVICES)
Fixes: https://forum.openwrt.org/t/luci-attended-sysupgrade-support-thread/230552/246
Fixes: https://github.com/openwrt/asu/issues/486
Fixes: https://github.com/openwrt/asu/issues/524
Fixes: 9aa66b8ce7 "sunxi: add support for Banana Pi M2 Berry"
Fixes: d5f615bf2a "sunxi: add support for Sinovoip Banana Pi M2 Plus"
Fixes: 3819c1638a "sunxi: Add support for Banana Pi M2 Ultra"
Fixes: 6bf8193b25 "sunxi: add support for Bananapi P2 Zero"
Fixes: 80edfaf675 "sunxi: add support for Banana Pi M3"
Fixes: 3c24a1d423 "sunxi: add support for NanoPi NEO Plus2 board"
Fixes: a689307c97 "sunxi: build image/uboot for the NanoPi NEO2"
Fixes: fde68cb809 "sunxi: add support for FriendlyARM NanoPi R1S H5"
Fixes: 3ec468ff4f "sunxi: add F1C100 (arm926ej-s) support"
Signed-off-by: Mario Andrés Pérez <mapb_@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21095
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d871e95e7f)
Modernize the target slightly to use kernel+dtb FIT images in all
subtargets. LZMA compression will be used for the cortexa53 devices,
and we'll stay conservative and use gzip for the cortexa7/a8 devices
due to performance differences.
Tested-on:
- Linksprite pcDuino v2 (cortexa8 / A10)
- Olinuxino Micro (cortexa7 / A20)
- Banana Pi M2 Berry (cortexa7 / V40)
- Banana Pi P2 Zero (cortexa7 / H2+)
- Xunlong Orange Pi 2 (cortexa7/ H3)
- OrangePi PC Zero 2 (cortexa53 / H616)
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
As preparation for the arm926ej-s support which has a different
load address, move the KERNEL_LOADADDR into the subtargets.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Key features:
Allwinner H618 SoC (Quad core Cortex-A53)
1/1.5/2/4 GiB LPDDR4 DRAM
1 USB 2.0 type C port (Power + OTG)
1 USB 2.0 host port
1Gbps Ethernet port
Micro-HDMI port
MicroSD slot
Installation:
Write the image to SD Card with dd.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The firmware for the rtl8723bs chip is now included in the
rtl8723bu-firmware package.
Fixes: 397dfe4a97 ("linux-firmware: Update to version 20121216")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
CPU: Allwinner H5, Quad-core Cortex-A53
DDR3 RAM: 512MB
Network: 10/100/1000M Ethernet x 2
USB Host: Type-A x 1
MicroSD Slot x 1
MicroUSB: for power input
Debug Serial Port: 3Pin pin-header
LED: WAN, LAN, SYS
KEY: Reset
Power Supply: DC 5V/2A
Installation:
Write the image to SD Card with dd.
Note:
1. OpenWrt currently does not support LED_FUNCTION, change back to the
previous practice (Consistent with NanoPi R1).
2. Since the upstream commit https://github.com/torvalds/linux/bbc4d71
("net: phy: realtek: fix rtl8211e rx/tx delay config"), we need to
change the phy-mode from rgmii to rgmii-id.
So set phy-mode for 5.4 and 5.10 respectively.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Many target use a repetitive if-include scheme for their subtarget
image files, though their names are consistent with the subtarget
names.
This patch removes these redundant conditions and just uses the
variable for the include where the target setup allows it.
For sunxi, this includes a trivial rename of the subtarget image
Makefiles.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-11 01:44:13 +02:00
Renamed from target/linux/sunxi/image/cortex-a53.mk (Browse further)
