rev B1 is identical to rev A1 except for different PHYs on the 2.5gbps ports (lan9 and lan10)
Both revisions of xgs1210-12 are also switched to use rt-loader to avoid
problems due to overwriting the compressed image in memory when flashing
with the oem firmware (and also to save flash space with respect to gzip
compression)
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20161
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Both devices, the Linksys WHW01 and the VLP01, are essentially the same
device. Even Linksys provides only one image for both devices which uses
the WHW01 identifier in the image header.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20455
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for the Cisco Meraki MR30H. The MR30H is a POE
powered 802.11ac access point with an integrated 5 port Gigabit switch.
MR30H hardware info:
* CPU: Qualcomm IPQ4029
* RAM: 256MB DDR3
* Storage: 128 MB (S34ML01G200TFV00)
* Networking: QCA8075 internal switch (5x 1GbE ports)
* WiFi: QCA4019 802.11b/g/n/ac, QCA9889 802.11/b/g/n/ac scanning radio
* Serial: Internal header (J8, 2.54mm, populated)
LAN5 (rear) is for POE input. LAN4 has POE output (802.3af) when powered
by an 802.3at source.
The LAN4 port is used for tftp booting in U-Boot.
This device does not have secure boot, but cannot be flashed without
external programmers (TSOP48 NAND) as Meraki disabled interrupting U-Boot
for any device that updated after ~2017.
Disassembly:
* Remove the two T10 screws on the rear of the AP.
* Using a guitar pick or similar plastic tool, insert it on the side between
the grey metal plate and the white plastic body and pry up gently.
* The rubberised border on the metal plate does not need to be removed.
* The metal back plate has several latches around the perimeter (but none on
the bottom by the Ethernet ports).
* Once you have removed the metal back plate, push up gently on the bottom
Ethernet ports while pulling gently on the rear-mounted Ethernet port to remove
the PCB.
* The PCB should come free from the plastic housing, pull the bottom
(4 Ethernet ports) up as if you are opening a book.
* If done carefully, there is no need to remove the WiFi antenna connectors
to access the NAND flash.
* The TSOP48 NAND flash (U30, Spansion S34ML01G200TFV00) is located on the
opposite side of the PCB.
* To flash, you need to desolder the TSOP48 or use a 360 clip.
Installation:
The dumps to flash can be found in this repository:
https://github.com/halmartin/meraki-openwrt-docs/tree/main/mr30h
The device has the following flash layout (offsets with OOB data):
```
0x000000000000-0x000000100000 : "sbl1"
0x000000100000-0x000000200000 : "mibib"
0x000000200000-0x000000300000 : "bootconfig"
0x000000300000-0x000000400000 : "qsee"
0x000000400000-0x000000500000 : "qsee_alt"
0x000000500000-0x000000580000 : "cdt"
0x000000580000-0x000000600000 : "cdt_alt"
0x000000600000-0x000000680000 : "ddrparams"
0x000000700000-0x000000900000 : "u-boot"
0x000000900000-0x000000b00000 : "u-boot-backup"
0x000000b00000-0x000000b80000 : "ART"
0x000000c00000-0x000007c00000 : "ubi"
```
* Dump your original NAND (if using nanddump, include OOB data).
* Decompress `u-boot.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `u-boot` portion of NAND from
`0x738000`-`0x948000` (length `0x210000`). Offsets here include OOB data.
* Resolder the NAND after overwriting the `u-boot` regions.
OpenWrt Installation:
* After flashing NAND with the external programmer. Plug an Ethernet
cable into port 4. Power up the device.
* The new U-Boot build uses the space character `" "` (without quotes) to
interrupt boot.
* Interrupt U-Boot and `tftpboot` the OpenWrt initramfs image from your
tftp server
```
dhcp
setenv serverip <your_tftp>
tftpboot openwrt-ipq40xx-generic-meraki_mr30h-initramfs-uImage.itb
```
* Once booted into the OpenWrt initramfs, `scp` the `sysupgrade` image to
the device and run the normal `sysupgrade` procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Alternative installation steps if your device has U-Boot older than:
`U-Boot 2017.07-RELEASE-g78ed34f31579 (Sep 29 2017 - 07:43:44 -0700)`
**BIG FAT WARNING BEGIN**
Attmping to interrupt boot on a newer U-Boot release may permanently
brick your device! See: riptidewave93/LEDE-MR33#13
**BIG FAT WARNING END**
* Use `ubootwrite.py` from the above GitHub repository to transfer the
`u-boot.itb`
image to the router.
```
./ubootwrite.py --serial=/dev/ttyUSB0 --write u-boot.itb
```
* To avoid bricking your router, it is highly recommended at this point that
you flash the unlocked U-Boot to the `part.safe` ubi volume.
```
run set_ubi && ubi write $loadaddr part.safe 0x2fd48
```
* Power cycle the router. The stock Meraki U-Boot will boot `part.safe` which
is now the unlocked U-Boot.
* Use the new U-Boot build (`" "` to interrupt boot) to
`tftpboot` the OpenWrt initramfs image:
```
dhcp
setenv serverip <tftp_server_addr>
tftpboot openwrt-ipq40xx-generic-meraki_mr30h-initramfs-uImage.itb
bootm
```
* It is only recommended to flash U-Boot to the `u-boot` NAND region from
Linux:
```
insmod mtd-rw i_want_a_brick=1
```
* Copy `u-boot.elf` to the router:
```
scp -O u-boot.elf root@192.168.1.1:/tmp/
```
Note: If any of the below commands fails, YOU WILL HAVE A BRICK IF YOU
REBOOT OR LOSE POWER. Only a hardware programmer can recover the device.
```
flash_erase /dev/mtd8 0 0
nandwrite -p /dev/mtd8 /tmp/u-boot.elf
```
Note: ONLY use `u-boot.elf` when flashing the `u-boot` region (`/dev/mtd8`);
`u-boot.bin` or `u-boot.itb` will BRICK YOUR DEVICE
* `scp` the `sysupgrade` image to the device and run the normal `sysupgrade`
procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17026
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for the Cisco Meraki Go GX20. The Go GX20 is a wired
router with 5 port Gigabit switch. It shares the same PCB as the Meraki Z3,
but without the WiFi radios.
GX20 hardware info:
* CPU: Qualcomm IPQ4029
* RAM: 512MB DDR3
* Storage: 128 MB (S34ML01G200TFV00)
* Networking: QCA8075 internal switch (5x 1GbE ports)
* USB: 1x USB3.0
* Serial: Internal header (J8, 2.54mm, populated)
Port 5 has POE output (802.3af). The Internet/WAN port is used for tftp booting
in U-Boot.
This device ships with secure boot, and cannot be flashed without
external programmers (TSOP48 NAND and I2C EEEPROM)!
Disassembly:
* Remove the four T8 screws on the bottom of the device under the rubber feet.
* Using a guitar pick or similar plastic tool, insert it on the side between
the bottom case and the side, pry up gently. The plastic bottom has several
latches around the perimeter (but none on the rear by the Ethernet ports).
* The TSOP48 NAND flash (U30, Spansion S34ML01G200TFV00) is located on the
bottom side of the PCB (facing you as you remove the bottom plastic).
To flash, you will need to desolder the TSOP48. Attempts to flash in-circuit
using a 360 clip were unsuccessful.
* The SOIC8 I2C EEPROM (U32, Atmel 24C64) is located on the bottom side of
the PCB (facing you as you remove the bottom plastic). It can be flashed in
circuit using a SOIC8 chip clip.
Installation:
The dumps to flash can be found in this repository:
https://github.com/halmartin/meraki-openwrt-docs/tree/main/z3_gx20
The device has the following flash layout (offsets with OOB data):
```
0x000000000000-0x000000100000 : "sbl1"
0x000000100000-0x000000200000 : "mibib"
0x000000200000-0x000000300000 : "bootconfig"
0x000000300000-0x000000400000 : "qsee"
0x000000400000-0x000000500000 : "qsee_alt"
0x000000500000-0x000000580000 : "cdt"
0x000000580000-0x000000600000 : "cdt_alt"
0x000000600000-0x000000680000 : "ddrparams"
0x000000700000-0x000000900000 : "u-boot"
0x000000900000-0x000000b00000 : "u-boot-backup"
0x000000b00000-0x000000b80000 : "ART"
0x000000c00000-0x000007c00000 : "ubi"
```
* Dump your original NAND (if using nanddump, include OOB data).
* Decompress `u-boot.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `u-boot` portion of NAND from
`0x738000`-`0x948000` (length `0x210000`). Offsets here include OOB data.
* Decompress `ubi.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `ubi` portion of NAND from
`0xc60000`-`0x8400000` (length `0x77a0000`). Offsets here include OOB data.
* Dump your original EEPROM. Change the byte at offset `0x49` to `0x1e`
(originally `0x2b`). Remember to re-write the EEPROM with the modified data.
* This can be done on Linux via the following command:
`printf "\x1e" | dd of=/tmp/eeprom.bin bs=1 seek=$((0x49)) conv=notrunc`
**Note**: the device will not boot if you modify the board major number and
have not yet overwritten the `ubi` and `u-boot` regions of NAND.
* Resolder the NAND after overwriting the `u-boot` and `ubi` regions.
OpenWrt Installation:
* After flashing NAND and EEPROM with external programmers. Plug an Ethernet
cable into the Internet/WAN port. Power up the device.
* The new U-Boot build uses the space character `" "` (without quotes) to
interrupt boot.
* Interrupt U-Boot and `tftpboot` the OpenWrt initramfs image from your
tftp server
```
dhcp
setenv serverip <your_tftp>
tftpboot openwrt-ipq40xx-generic-meraki_gx20-initramfs-uImage.itb
```
* Once booted into the OpenWrt initramfs, `scp` the `sysupgrade` image to
the device and run the normal `sysupgrade` procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_gx20-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_gx20-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17026
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for the Cisco Meraki Z3. The Z3 is a "teleworker"
device with 802.11ac and an integrated 5 port Gigabit switch.
Z3 hardware info:
* CPU: Qualcomm IPQ4029
* RAM: 512MB DDR3
* Storage: 128 MB (S34ML01G200TFV00)
* Networking: QCA8075 internal switch (5x 1GbE ports)
* WiFi: QCA4019 802.11b/g/n/ac
* USB: 1x USB3.0
* Serial: Internal header (J8, 2.54mm, populated)
Port 5 has POE output (802.3af). The Internet/WAN port is used for tftp booting
in U-Boot.
This device ships with secure boot, and cannot be flashed without
external programmers (TSOP48 NAND and I2C EEEPROM)!
Disassembly:
* Remove the four T8 screws on the bottom of the device under the rubber feet.
* Using a guitar pick or similar plastic tool, insert it on the side between
the bottom case and the side, pry up gently. The plastic bottom has several
latches around the perimeter (but none on the rear by the Ethernet ports).
* The TSOP48 NAND flash (U30, Spansion S34ML01G200TFV00) is located on the
bottom side of the PCB (facing you as you remove the bottom plastic).
To flash, you will need to desolder the TSOP48. Attempts to flash in-circuit
using a 360 clip were unsuccessful.
* The SOIC8 I2C EEPROM (U32, Atmel 24C64) is located on the bottom side of
the PCB (facing you as you remove the bottom plastic). It can be flashed in
circuit using a SOIC8 chip clip.
Installation:
The dumps to flash can be found in this repository:
https://github.com/halmartin/meraki-openwrt-docs/tree/main/z3_gx20
The device has the following flash layout (offsets with OOB data):
```
0x000000000000-0x000000100000 : "sbl1"
0x000000100000-0x000000200000 : "mibib"
0x000000200000-0x000000300000 : "bootconfig"
0x000000300000-0x000000400000 : "qsee"
0x000000400000-0x000000500000 : "qsee_alt"
0x000000500000-0x000000580000 : "cdt"
0x000000580000-0x000000600000 : "cdt_alt"
0x000000600000-0x000000680000 : "ddrparams"
0x000000700000-0x000000900000 : "u-boot"
0x000000900000-0x000000b00000 : "u-boot-backup"
0x000000b00000-0x000000b80000 : "ART"
0x000000c00000-0x000007c00000 : "ubi"
```
* Dump your original NAND (if using nanddump, include OOB data).
* Decompress `u-boot.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `u-boot` portion of NAND from
`0x738000`-`0x948000` (length `0x210000`). Offsets here include OOB data.
* Decompress `ubi.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `ubi` portion of NAND from
`0xc60000`-`0x8400000` (length `0x77a0000`). Offsets here include OOB data.
* Dump your original EEPROM. Change the byte at offset `0x49` to `0x1e`
(originally `0x24`). Remember to re-write the EEPROM with the modified data.
* This can be done on Linux via the following command:
`printf "\x1e" | dd of=/tmp/eeprom.bin bs=1 seek=$((0x49)) conv=notrunc`
**Note**: the device will not boot if you modify the board major number and
have not yet overwritten the `ubi` and `u-boot` regions of NAND.
* Resolder the NAND after overwriting the `u-boot` and `ubi` regions.
OpenWrt Installation:
* After flashing NAND and EEPROM with external programmers. Plug an Ethernet
cable into the Internet/WAN port. Power up the device.
* The new U-Boot build uses the space character `" "` (without quotes) to
interrupt boot.
* Interrupt U-Boot and `tftpboot` the OpenWrt initramfs image from your
tftp server
```
dhcp
setenv serverip <your_tftp>
tftpboot openwrt-ipq40xx-generic-meraki_z3-initramfs-uImage.itb
```
* Once booted into the OpenWrt initramfs, created the `ART` ubivol with
the WiFi radio calibration from the mtd partition:
```
cat /dev/mtd10 > /tmp/ART.bin
ubimkvol /dev/ubi0 -N ART -s 524288
ubiupdatevol /dev/ubi0_1 /tmp/ART.bin
```
* `scp` the `sysupgrade` image to
the device and run the normal `sysupgrade` procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_z3-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_z3-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17026
Signed-off-by: Robert Marko <robimarko@gmail.com>
whw01 was incorrectly placed below whw03 definitions.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20441
Signed-off-by: Robert Marko <robimarko@gmail.com>
This adds led aliases for failsafe and upgrade. Before this change the
leds stayed dark in both situations.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20441
Signed-off-by: Robert Marko <robimarko@gmail.com>
Set the label-mac-device to be able to easily fetch the mac-address of
the device, which is printed on the bottom of the case.
While at it, remove the TODO - the ethernet0 alias is needed to get the
mac from bootloader.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20441
Signed-off-by: Robert Marko <robimarko@gmail.com>
kernel 6.9 removed the KConfig entry our RouterBOOT watchdog pet hack was relying on:
Linux df59427a1122 ("ARM: qcom: merge remaining subplatforms into sensible Kconfig entry")
Introduce a new specific KConfig entry for this hack,
and enable it for Mikrotik ipq40xx kernel.
CONFIG_ARCH_QCOM_IPQ40XX_BOOT_COMPRESSED_PET_WATCHDOG_EARLY
With appropriate DEBUG_LL and DEBUG_UNCOMPRESS, this watchdog reset
can be typically seen on console as a reset before "Uncompressing Linux..."
reaches " done, booting the kernel."
RouterBOOT
loading kernel... OK
setting up elf image... OK
jumping to kernel code
Jumping to kernel
DTB:0x80381A60 (0x000048C4)
C:0x800000E0-0x80386420->0x80FAB500-0x81331840
DTB:0x8132CE80 (0x000049B8)
Uncompressing Linux...
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00096
versus:
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
On Mikrotik RouterBOOT devices, this is complicated by some RouterBOOT
versions successfully loading the same kernel that other RouterBOOT versions fail. Example:
RouterBOOT backup booter 6.45.9 fine, RouterBOOT booter 7.16 fail
Fixes: openwrt#19841
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Link: https://github.com/openwrt/openwrt/pull/20305
Signed-off-by: Robert Marko <robimarko@gmail.com>
The imagebuilder is not intended to build initramfs images. Some
profiles attempt to do this and succeed, due to buildroot leaking
the initramfs-kernel into staging_dir; others attempt it, but fail
due to not having initramfs binaries present in the imagebuilder.
Fix this by adding an explict guard around the unsupported generation
of the initramfs images. This saves space and time during imagebuilder
runs, fixes those that are currently broken and protects against future
breakage for profiles that inadvertently work now.
Fixes: https://github.com/openwrt/openwrt/issues/20151
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20347
Signed-off-by: Robert Marko <robimarko@gmail.com>
CONFIG_MTD_CFI was disabled in p1010 subtarget.
It causes problem with Aerohive BR200-WP router.
This patch enables CONFIG_MTD_CFI in p1010 config-default file.
Fixes: e9dd6da916 ("mpc85xx: p1010: add missing symbols")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20419
Signed-off-by: Nick Hainke <vincent@systemli.org>
The DSA driver must flush the HW FDB when a port changes from
learning/forwarding to disabled/blocking/listening.
But the implementation for RTL931x was writing the port information
starting at bit 11 (bit 11 of the second 32-bit L2_TBL_FLUSH_CTRL
register). But this offset is the AGG_VID and not the port. The actual
position is 43 (bit 11 of the first register).
As result, the FDB was always only flushed for the port 0 and not for the
selected port.
Fixes: 9ed6097054 ("realtek: Add HW support for RTL931X for PIE, L2 and STP aging")
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20422
Signed-off-by: Robert Marko <robimarko@gmail.com>
the eth1 interface was renamed to wan so also reflect that change in
the leds setup script
Fixes: f26260c7e7 ("mediatek: filogic: Add label wan and cpu for Zyxel EX5601-T0")
Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20120
Signed-off-by: Nick Hainke <vincent@systemli.org>
BPDU frames like STP must be processed by each switch (bridge) which
supports STP. It must not be forwarded to avoid confusing the STP state of
other STP participants. It is essential to be an active participant of STP.
The software bridge automatically takes care of forwarding the BPDUs to
other ports when STP is disabled and the hardware switch should not
interfere.
Signed-off-by: Harshal Gohel <hg@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20414
Signed-off-by: Robert Marko <robimarko@gmail.com>
With this patch is set the maximum number of connections per ip address instead of no control.
The default is 8.
Signed-off-by: Andrea Pesaresi <andreapesaresi82@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20377
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
backport from kernel 6.12
ksmbd.mount will give each interfaces list and bind_interfaces_only flags
to ksmbd server. Previously, the interfaces list was sent only
when bind_interfaces_only was enabled.
ksmbd server browse only interfaces list given from ksmbd.conf on
FSCTL_QUERY_INTERFACE_INFO IOCTL.
Signed-off-by: Andrea Pesaresi <andreapesaresi82@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20377
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch resolves the LAN port not initializing on the
FriendlyElec NanoPI R4S, especially during warm reboots.
Upstream commit patch is based on:
c3fe7071e1
I've experienced the LAN port failing to initialize from a cold boot and
after a reboot. Other users have reported this issue on
https://forum.openwrt.org/t/nanopi-r4s-rk3399-is-a-great-new-openwrt-device/79143.
The NanoPI R4S has its LAN port connected to the RK3399 via PCIE. Since the
PCIE lanes don't initialize correctly after reboot, the LAN port
doesn't initialize.
Signed-off-by: Timothy Feierabend <tim.feierabend@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20406
Signed-off-by: Nick Hainke <vincent@systemli.org>
Now that we have a board file, add calibration variant for TP-Link
Archer C59 v1 and add ipq-wifi package for it.
Tested-by: Mateusz Jończyk <matjon@users.noreply.github.com>
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20401
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit 468975a985 changed the XO board clock definition from a fixed
clock to a fixed rate clock in the dtsi.
As such, boards must use clock dividers and multipliers to calculate
the clock rate based on the referenced parent clock.
Fixes: 5d2994a73e ("qualcommax: ipq50xx: Add support for Yuncore AX850")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20405
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix a regression introduced by a recent commit.
It looks like a copy/paste error.
Add the missing line which defines the 'board' val
as it does not exist otherwise in the case check.
This fixes sysupgrade on ath79 MikroTik non-NOR boards.
Fixes: 318f07c231 ("ath79: mikrotik: check RouterBOOT version matching sysupgrade image")
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Add pending patch to address PCI sysfs creation entry race observed on
ipq806x. This is to handle a kernel warning on creating the same sysfs
entry multiple times.
All affected patch automatically refreshed.
Link: https://github.com/openwrt/openwrt/pull/18989
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Adapt OPP patch with upstream changes to cpufreq driver. Use the krait
compatible and the new opp-supported-hw way instead of deleting nodes.
Link: https://github.com/openwrt/openwrt/pull/18989
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The 6.12 testing kernel for ipq806x target is ready now.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18989
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
- Reuse the bridges node defined on "qcom-ipq8064.dtsi".
- Rename PCIe device nodes to unified "wifi@0,0".
- Add the missing "qcom,ath10k" compatibles.
- Remove unseless property "interrupt-controller". There are no
consumers use these PCIe devices as interrupt controllers.
- Change bus number from 0 to 1, just like other ipq806x devices.
The valid PCIe bus range on this platform is 1 - 255.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18989
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add bridge node labels so that we can insert PCIe peripheral nodes.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18989
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Copy patches and kernel configs from 6.12 kernel to restore the
default 6.6 kernel support files.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18989
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is a preparation for 6.12 kernel support. It can help us
track the patches and Kconfig history by using the Git tool.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18989
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is a preparation for introducing the 6.12 kernel support.
All configs are automatically refreshed. In theory, they will
generate the same .config files in the kernel build directory
as before.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18989
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Right now the phylink capability function enables 2.5G and 10G modes on
Maple and Cypress, which they mostly (other than two SERDES on Cypress)
don't support. This causes these modes to be selected and break the link
as they are not supported by hardware.
I looked into doing this properly, but it cannot just be done based on
SoC, but needs to take the whole topology into account as a given MAC
might have very different capabilities depending on what SERDES are
assigned to it. So for now just use 1G and QSGMII for RTL83xx and 10G
for RTL93xx. This mostly works, except it will downgrade some 10G links
on RTL839x, but since there are also 1G SFPs on these this cannot be
solved without fully accounting for the global MAC and SERDES
configuration.
So this makes all of the 1G SFP slots work again, while keeping most of
the 10G SFP+ slots working at 10G with minimal changes.
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Link: https://github.com/openwrt/openwrt/pull/20374
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If the devicetree contains the appropriate nodes to configure the MAC
addresses for each physical DSA port, then these MAC addresses must be used
in OpenWrt and not some automatically generated ones. Otherwise the device
often ends up with addresses which are locally administered and not
matching any expected port-to-MAC scheme.
Devices which only get the MAC address for eth0 must still auto-generate
these MAC addresses until the devicetree was updated to also include the
correct ones.
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20241
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If the lan_mac cannot be found, it is still used (as empty string) in
various operations. This is not valid and other 02_network scripts checking
for a non-empty string before using it. This should also be adopted for the
realtek 02_network.
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20241
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Having everything in a big script without any structure makes it
unnecessary hard to get an overview or modify it without triggering
unexpected side effects.
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20241
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The preferred prefix for the Realtek DSA driver code is "rtldsa" and no
longer "rtl83xx". This makes sure that the different drivers have
non-conflicting prefixes and because of this non-conflicting function
names.
Suggested-by: Felix Baumann <felix.bau@gmx.de>
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20360
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RTL930x and the RTL931x SoC families share the same struct
dsa_switch_ops. This should be represented in the name of the object.
Suggested-by: Felix Baumann <felix.bau@gmx.de>
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20360
Signed-off-by: Robert Marko <robimarko@gmail.com>
If two ports are in isolation mode then these ports are not supposed to be
able to communicate between each other. This can be achieved in the realtek
switch by removing the other isolated port(s) from the port list of an
isolated port.
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20360
Signed-off-by: Robert Marko <robimarko@gmail.com>
The realtek driver is now in full control of the port matrix. It doesn't
need to rely on the current state of the HW to adjust it. The new port
matrix is calculated automatically using rtldsa_update_port_member() and
then written to the registers/tables.
Signed-off-by: Sven Eckelmann <se@simonwunderlich.de>
Link: https://github.com/openwrt/openwrt/pull/20360
Signed-off-by: Robert Marko <robimarko@gmail.com>
