There are still a lot of mdio functions scattered around the code.
Move the RTL838x serdes helpers closer to the bus, add the proper
prefix and simplify the functions.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18847
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is a patch/bug cascade in the realtek target phy code that must be resolved.
1. The phy_driver structure is patched to add features ONLY needed for RTL8214FC
2. The kernel is patched to allow switching fiber/copper port of phys through ethtool
by calling these new features.
3. With those patches applied the bootup always switches RTL8214FC ports to copper.
Even if a SFP module was found before and the phy driver switched to fibre before.
3. So another patch is needed that reprobes the SFP module to activate fiber again.
4. Because of the reprobing we need a fourth patch that avoid duplicate devices.
Simplify this by removing all patches and reusing the existing ethtool phy tunable
interface. The command line usage might be counterintuitive but it avoids tons of
problems in the code. In addition, this scenario is not used frequently.
Before:ethtool -s lan25 port fibre/tp
After: ethtool --set-phy-tunable lan25 downshift on/off
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18816
Signed-off-by: Robert Marko <robimarko@gmail.com>
We have modified the kernel to setup all "default" consoles,
including serial ports and framebuffers/screens, providing
no console= argument is supplied on the kernel command line.
Adding 'console=tty1' caused the 'default' serial port on
device tree systems to break, as the kernel would not carry
over the settings (like baud rate) from the bootloader.
The system administrator can still force the use of a
specific console by adding their own console= arguments.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Fixes: c099523d66 ("armsr: use console=tty1 to make
console more readily available")
Link: https://github.com/openwrt/openwrt/pull/17012
Signed-off-by: Robert Marko <robimarko@gmail.com>
A previous change added 'console=tty1' to the default kernel command
line on armsr, in order to ensure the framebuffer console is enabled
on systems capable of graphics output.
Unfortunately, this change broke boards that used device tree
(DT) firmware with serial consoles, as the serial console
specified by the system firmware (stdout-path) was no longer
setup by the kernel.
A bit of probing determined that the SPCR (serial port console
direction table) on ACPI systems was preventing Linux from setting
up a default framebuffer console on these systems (which is why
console=tty1 was added).
(The affected ACPI systems are usually VMs using QEMU's
'virt' machine and EDK2 firmware. The firmware on these systems
does not remove the SPCR when a screen is present)
So to ensure all possible systems are setup correctly, we modify
the kernel so all "default" console types (serial and screen)
are setup when no console= arguments are specified on the kernel
command line.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Fixes: c099523d66 ("use console=tty1 to make console more
readily available")
Link: https://github.com/openwrt/openwrt/pull/17012
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh patches to fix the GitHub CI warning.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18912
Signed-off-by: Nick Hainke <vincent@systemli.org>
SOC: MediaTek MT7981b
RAM: 256MB DDR3
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7981b DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Interface MAC Algorithm
LAN 8C:AE:DB:2C:xx:xx label
WAN 8C:AE:DB:2C:xx:xx label +1
WLAN 2.4G 8C:AE:DB:2C:xx:xx label +2
WLAN 5G 8C:AE:DB:2C:xx:xx label +3
Installation
-------------------Install openwrt image-------------------------------:
Set a static ip on the ethernet interface of your PC. (ip address:
192.168.1.254, subnet mask:255.255.255.0) .
Download the OpenWrt uboot image
(openwrt-mediatek-filogic-snr_cpe-ax2-bl31-uboot.fip).
SSH/SCP opened by default on the stock firmware (3.0.1).
Username: Admin, default password: Admin. Check it on the bottom of
the router.
Copy uboot image using SCP (WinSCP) to /tmp dir on SNR-CPE-AX2.
Download recovery file.
openwrt-mediatek-filogic-snr_snr-cpe-ax2-initramfs-recovery.itb.
Copy the recovery image to a TFTP server reachable at 192.168.1.254/24.
Open ssh shell to the SNR-CPE-AX2.
Run commands:
mtd write \
/tmp/openwrt-mediatek-filogic-snr_snr-cpe-ax2-bl31-uboot.fip FIP
reboot
Wait until recovery boot.
Open web 192.168.1.1 and do sysupgrade by
openwrt-mediatek-filogic-snr_cpe-ax2-squashfs-sysupgrade.itb
Signed-off-by: Nikolay March <palladin82@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/18700
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Sort the config in alphabetical order
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/18897
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Upstream seems to be using led-sources instead of custom properties.
Code mostly taken from mt76.
Changed all(few) users of qca,led_pin to use the new format.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18805
Signed-off-by: Robert Marko <robimarko@gmail.com>
The MIPS CPC (Cluster Power Controller) is setup during boot and can take
its configuration from the devicetree. This is currently not possible
because the cpc probing happens before dt initialization. Call order
during startup is:
setup_arch()
prom_init() <- our function
mips_cpc_probe()
smp_stuff()
arch_mem_init()
device_tree_init() <- our function
unflatten_and_copy_device_tree()
To avoid ugly hacking and support a clean devicetree relocate the cps/smp
stuff to device_tree_init(). This is basically the same location as in
generic mips initialization.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Link: https://github.com/openwrt/openwrt/pull/18888
Signed-off-by: Robert Marko <robimarko@gmail.com>
Make it easier to upgrade the kernel in the future. For this remove
the 320-harden-fw_init_cmdline.patch and add the logic into the
startup sequence at the right place.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18853
Signed-off-by: Robert Marko <robimarko@gmail.com>
The 6.12 testing kernel for ath79 target is ready now.
Tested on AR9344 (ath79/nand) and QCA9531 (ath79/generic).
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
All kernel symbols are automatically refreshed by
`make kernel_oldconfig CONFIG_TARGET=target` and
`make kernel_oldconfig CONFIG_TARGET=subtarget`.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
This is a preparation for 6.12 kernel support. It can help us
track the files history by using the Git tool.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Manually move the common NVMEM Kconfig symbols to the shared
config file and disable them for the mikrotik subtarget. Other
changes are automatically completed by `make kernel_oldconfig`.
This is a preparation for introducing the 6.12 kernel support.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
RTL931x devices are dual core with two threads each. That is a total
of 4 VPEs (CPUs) in the kernel. Adapt the kernel config for that.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Link: https://github.com/openwrt/openwrt/pull/18889
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use upstreamed v6.16 patches for IPQ5018 tsens support.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18884
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use upstreamed v6.16 patch for IPQ5018 TCSR support and setting the
download mode.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18884
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use upstreamed patches for IPQ5018 PCIe support, including patches for
phy and controller drivers and dts nodes.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18884
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Since the early beginning of the Realtek DSA driver there is an uncovered
locking issue between the standard (parent) mdio bus and the DSA (child)
mdio bus. This comes from the fact that the DSA bus simply links to the
parent read and write functions and calls them directly. This leads to
the following lock issue.
- Child bus calls phy_read/write functions and uses its internal lock
- Parent bus calls phy_read/write functions and uses its internal lock
It becomes clear that critical section can be accessed twice without
knowing that a operation from the other bus is currently active. This
can lead to critical malfunctions because the mdio driver needs a lot of
internal magic to get page selection done right. Effects are:
- The original page is lost after a phy_write/read_paged() call
- dmesg like "Realtek RTL8218B (external) rtl838x slave mii-0:00:
Expected external RTL8218B, found PHY-ID 6b23"
Other DSA drivers simply use the read/write functions from the parent bus
and thus avoid locking issues. Do it the same way.
Fixes: 2b88563ee5 ("realtek: update the tree to the latest refactored version")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18824
Signed-off-by: Robert Marko <robimarko@gmail.com>
Before generating the factory image, check if the input file
exists. Fix the build error when sysupgrade image is too big:
[mkwrgimg] *** error: stat failed on /builder/shared-workdir/build/build_dir/target-mipsel_24kc_musl/linux-ramips_rt288x/tmp/openwrt-ramips-rt288x-airlink101_ar670w-squashfs-factory.bin, No such file or directory
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18836
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This was needed while ar71xx was in tree. This is no longer the case.
Not only that, these have already been converted to OF.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18860
Signed-off-by: Robert Marko <robimarko@gmail.com>
