To avoid unneeded interrupts the R4K timer is deactivated during
secondary cpu initialization. This is currently done during
phase init_secondary(). With the upgrade to 6.12 the kernel runs
a primary/secondary cpu timer/counter synchronization to verify the
proper setup in synchronise_count_slave(). That runs at a later
point in time and expects the secondary counter to be fully
functional. Finding a deactivated counter results in the following
messages:
WARNING: CPU: 1 PID: 0 at arch/mips/kernel/sync-r4k.c:99 check_counter_warp+0x220/0x254
Warning: zero counter calibration delta: 0 [max: 6500000]
Counter synchronization [CPU#0 -> CPU#1]:
Measured 278760029 cycles counter warp between CPUs
Relocate the deactivation to smp_finsh() at the end of the cpu
startup sequence. Additionally polish the startup code and remove
all unneeded parts.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Per IEEE 802.3 definition we have:
- parallel XGMII for single 10GBit ONLY links
- serial USGMII for 8 port 1GBit links (not known by kernel)
- serial USXGMII: for single/multiple links with a total bandwidth of 10GBit
The phy-mode of the first eight ports of the XGS1250-12 have always been
defined as XGMII (without S). This came from a confusion with the similar
named Realtek proprietary XSGMII (with S) mode that is basically 10GB SGMII.
From the above definition this is wrong but worked until kernel 6.6. With
the upgrade to 6.12 there is an enforced capabilities check within
phy_caps_from_interface() and link validation fails with
lan1: validation of xgmii with support 62ef and advertisement 62c0 failed: -EINVAL
lan1: failed to connect to PHY: -EINVAL
lan1: error -22 setting up PHY for tree 0, switch 0, port 0
Switch the ports to USXGMII as the most flexible option. This might be no
final solution but at least it better describes the phy/mac link.
Fixes 5b8b382df9 ("realtek: Add support for ZxXEL XGS1250-12 Switch")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix minor compilation errors due to kernel changes.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream has integrated the Realtek target into the generic MIPS
initialization and so MACH_REALTEK_RTL has gained some new features.
Especially:
- CONFIG_MACH_GENERIC_CORE generates central modules
- board-realtek module adds device specific extensions
The current downstream initialization works well and upgrading to
kernel 6.12 is not the right time to harmonize this. Modify the
MACH definitions to the current needs.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
The validate function no longer exists in phylink_mac_ops. Remove
it for the internal ethernet interface. Instead provide some
meaningful mac capabilities.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Not only the link but also the mac capabilities are needed here.
Additionally do some alphabetical sorting.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
The old upstream notation has been changed to something not so racist.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
EEE functions are now called with ethtool_keee instead of
ethtool_eee. Replace all occurrences. This will fix function
signature checks but still produces compilation errors due
to structure changes.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Patches where fuzz had to be cleaned up.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
All these patches needed no manual intervention and applied cleanly
with new source code positions.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Thanks to Chris Packham this driver got upstreamed. Drop the
downstream files and patches.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Automatically generated commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Automatically generated commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Automatically generated commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Automatically generated commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Automatically generated commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Automatically generated commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add kernel package for Broadcom Settop/DSL I2C controller.
This controller is used on RPi devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This commit changes LAN1 to be WAN and LAN2 to be LAN, like all other
dual port Extreme Networks devices.
This partially reverts commit 84a489b7cf
Signed-off-by: Christian Schmidbauer <github@grische.xyz>
Fixes LAN LED "1" to show activity of LAN1 and LAN LED "2" to show
activity of LAN2, not vice versa.
Signed-off-by: Christian Schmidbauer <github@grische.xyz>
Update the pin-configuration as well as maximum frequency for the eMMC
flash.
- Use 26 MHz as the maximum clock of the eMMC memory
- Configure 12mA as the pin drive-strength
- Enable internal pull-reistors
Signed-off-by: Yin Ni <yin.ni@gl-inet.com>
[adapt commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
The function name is misspelled and does not exist. Fix the function
name so the correct function is called.
Signed-off-by: David Bauer <mail@david-bauer.net>
Multiple users have reported a regression [1] in OpenWRT 24.10 with the
ramips/mt7621 target, which has the MT7530 PHYs: the Ethernet link is
periodically going down for a brief period of time:
mt7530-mdio mdio-bus:1f lan1: Link is Down
br-lan: port 1(lan1) entered disabled state
mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
The symptoms stop after disabling EEE and it was reported by Mediatek in
2021 that EEE is unstable for the MT7530 PHYs [2]:
> EEE of the 10-year-old MT7530 internal gephy has many IOT problems, so
> it is recommended to disable its EEE.
EEE is enabled by default for these devices in OpenWRT 24.10 whereas in the
previous version (OpenWRT 23.05, Linux 5.15) it was not. It was determined
that in Linux 6.6, the PHY driver tries to disable EEE in
mtk_gephy_config_init() in drivers/net/phy/mediatek-ge.c, but this is later
overridden by a subsequent execution of the genphy_c45_write_eee_adv()
function, which enables every EEE mode supported.
The best way forward for now seems to be to mark EEE as broken directly in
the devicetree, which affects the genphy_c45_write_eee_adv() function.
There are some devices, like GnuBee GB-PC2, that define additional PHYs,
for example ethernet-phy@5 or ethernet-phy@7. As reported by Chester A.
Unal, these are not MT7530 PHYs and they are not affected.
This would need to be cherrypicked for the OpenWRT 24.10 branch.
[1] https://github.com/openwrt/openwrt/issues/17351
[2] https://lore.kernel.org/all/0adde34f936a2dafca40b06b408d82afe0852327.camel@mediatek.com/
Tested-by: Darren Tucker
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Closes: https://github.com/openwrt/openwrt/issues/17351
Link: https://github.com/openwrt/openwrt/pull/18585
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specifications:
- SoC: Broadcom BCM6358 dual 300MHz MIPS
- Flash: 16MB NOR Macronix MX29GL128EHT2I-90G
- RAM: 64MB DDR
- Ethernet: 4x 100M
- Wifi: Ralink RT3062F
- 3x USB 2.0 port
- 4x Button
- 13x LED
- RJ11 2x FXS VoIP (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
- Assign static IP 192.168.1.100 to PC.
- Unplug the power source.
- Press the RESTART button at the router, don't release it yet!
- Plug the power source and wait at least 15 seconds.
- Release the RESTART button.
- Browse to http://192.168.1.1 with your PC.
- Upload the openwrt-bmips-bcm6358-huawei_hg556a-c-squashfs-cfe.bin file.
- Wait some minutes until the firmware upgrade completes.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
It's time to give the patches documentation some love by:
- Using Markdown.
- Differentiating between generic and specific target patches.
- Adding deeper explanation about patch numbering.
Link: https://github.com/openwrt/openwrt/pull/19092
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Missing headers causes an error on kernel 6.12:
arch/mips/ralink/irq.c:86:5: error: no previous prototype for 'get_c0_perfcount_int' [-Werror=missing-prototypes]
86 | int get_c0_perfcount_int(void)
| ^~~~~~~~~~~~~~~~~~~~
arch/mips/ralink/irq.c:92:14: error: no previous prototype for 'get_c0_compare_int' [-Werror=missing-prototypes]
92 | unsigned int get_c0_compare_int(void)
| ^~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18654
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Replace macros with empty body with 'do {} while (0)'.
Remove unnecessary semicolons.
Fixes:
drivers/mmc/host/mtk-mmc/sd.c: In function 'msdc_irq':
drivers/mmc/host/mtk-mmc/sd.c:1969:87: error: suggest braces around empty body in an 'else' statement [-Werror=empty-body]
1969 | IRQ_MSG("XXX CMD<%d> MSDC_INT_RSPCRCERR", cmd->opcode);
| ^
drivers/mmc/host/mtk-mmc/sd.c:1975:84: error: suggest braces around empty body in an 'else' statement [-Werror=empty-body]
1975 | IRQ_MSG("XXX CMD<%d> MSDC_INT_CMDTMO", cmd->opcode);
| ^
cc1: all warnings being treated as errors
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18654
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reorganize backported 6.12 generic patches, grouping them by following
a standard naming XXX-XX-v6.x-patch-file-name.patch.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add kernel package for DesignWare I2C platform controller.
This controller is used on the RP1 SoC found on RPi 5 devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add kernel packages for DesignWare SPI core and MMIO controllers.
This is needed for the RP1 SoC found on RPi 5 devices.
Tested with a Microchip ENC28J60 Ethernet controller on a RPi 5.
Signed-off-by: Albrecht Lohofener <albrechtloh@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19049
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add uboot-envtools (removing -uboot-envtools) to devices which were
missed in the commit 79bd017 ("ramips: mt7621: add uboot-envtools to
all devices")
- Mi Router 3G
- Mi Router AC2100
While at here remove two redundant entries from devices which were added
just after the referenced commit 79bd017 and did not account for the
new DEFAULT_PACKAGES member:
- SNR-CPE-ME1
- SNR-CPE-ME2-SFP
Fixes: 79bd017 ("ramips: mt7621: add uboot-envtools to all devices")
Fixes: https://github.com/openwrt/openwrt/issues/18960
Signed-off-by: Mario Andrés Pérez <mapb_@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19012
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the following to fix builds with GCC 15.1:
https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/arch/mips/vdso?h=next-20250606&id=0f4ae7c6ecb89bfda026d210dcf8216fb67d2333
% dmesg | grep gcc
[ 0.000000] Linux version 6.6.93 (facade@redline) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 15.1.0 r29972+15-7d617804cfe7) 15.1.0, GNU ld (GNU Binutils) 2.44) #0 SMP Sat Jun 7 12:13:18 2025
Error for reference:
./include/linux/stddef.h:11:9: error: cannot use keyword 'false' as enumeration constant
11 | false = 0,
| ^~~~~
./include/linux/stddef.h:11:9: note: 'false' is a keyword with '-std=c23' onwards
./include/linux/types.h:35:33: error: 'bool' cannot be defined via 'typedef'
35 | typedef _Bool bool;
| ^~~~
./include/linux/types.h:35:33: note: 'bool' is a keyword with '-std=c23' onwards
./include/linux/types.h:35:1: error: useless type name in empty declaration [-Werror]
35 | typedef _Bool bool;
| ^~~~~~~
CC arch/mips/lib/delay.o
AR arch/mips/fw/lib/built-in.a
AR arch/mips/fw/lib/lib.a
CC arch/mips/ralink/of.o
CC fs/read_write.o
CC block/elevator.o
cc1: all warnings being treated as errors
make[9]: *** [scripts/Makefile.build:243: arch/mips/vdso/vgettimeofday.o] Error 1
make[8]: *** [scripts/Makefile.build:480: arch/mips/vdso] Error 2
Build system: x86/64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19058
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch contains various minor FDT improvements for ramips
HiWiFi series devices:
* Add mt76 driver compatibles.
* Remove useless platform compatibles.
* Add default USB LED trigger for HC5861.
* Disable unused usbphy for HC5661, HC5661A and HC581B.
* Add switch port map properties based on 02_network scripts.
* Move aliases node to device dts because the LED nodes it
references only exist in the device specific dts.
* Rename gpio-leds nodes to follow the upstream dt-bindings
suggested pattern "(^led-[0-9a-f]$|led)".
* Convert deprecated LED label property to color and function.
"system" LED has been renamed to "status", it is acceptable
because these LEDs do not have text labels.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18251
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
For all HiWiFi series devices, the base MAC address is stored on
"bdinfo" partition, offset 0x18a, ASCII text format. The recently
introduced "mac-base" nvmem layout can handle the ASCII text now,
so it's time to move MAC address configurations to dts. There is
no valid MAC info in the "factory" partition, hence they will be
replaced with the correct ones.
Tested on HiWiFi HC5661A and HC5861.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18251
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specifications:
- SoC: Broadcom BCM6358 dual 300MHz MIPS
- Flash: 16MB NOR Spansion S29GL128P10
- RAM: 64MB DDR
- Ethernet: 4x 100M
- Wifi: Atheros AR9223
- 3x USB 2.0 port
- 4x Button
- 13x LED
- RJ11 2x FXS VoIP (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
- Assign static IP 192.168.1.100 to PC.
- Unplug the power source.
- Press the RESTART button at the router, don't release it yet!
- Plug the power source and wait at least 15 seconds.
- Release the RESTART button.
- Browse to http://192.168.1.1 with your PC.
- Upload the openwrt-bmips-bcm6358-huawei_hg556a-a-squashfs-cfe.bin file.
- Wait some minutes until the firmware upgrade completes.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Commit Fixes: 15430a1348 ("bmips: use wan ports as standalone ports")
removed bridge devices and therefore switch.1 no longer exists, so let's
use br-lan instead.
Fixes: 15430a1348 ("bmips: use wan ports as standalone ports")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
