Add IPQ Wifi entry for ath79 TP-Link Archer C60 v2.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20496
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for the Cisco Meraki MR30H. The MR30H is a POE
powered 802.11ac access point with an integrated 5 port Gigabit switch.
MR30H hardware info:
* CPU: Qualcomm IPQ4029
* RAM: 256MB DDR3
* Storage: 128 MB (S34ML01G200TFV00)
* Networking: QCA8075 internal switch (5x 1GbE ports)
* WiFi: QCA4019 802.11b/g/n/ac, QCA9889 802.11/b/g/n/ac scanning radio
* Serial: Internal header (J8, 2.54mm, populated)
LAN5 (rear) is for POE input. LAN4 has POE output (802.3af) when powered
by an 802.3at source.
The LAN4 port is used for tftp booting in U-Boot.
This device does not have secure boot, but cannot be flashed without
external programmers (TSOP48 NAND) as Meraki disabled interrupting U-Boot
for any device that updated after ~2017.
Disassembly:
* Remove the two T10 screws on the rear of the AP.
* Using a guitar pick or similar plastic tool, insert it on the side between
the grey metal plate and the white plastic body and pry up gently.
* The rubberised border on the metal plate does not need to be removed.
* The metal back plate has several latches around the perimeter (but none on
the bottom by the Ethernet ports).
* Once you have removed the metal back plate, push up gently on the bottom
Ethernet ports while pulling gently on the rear-mounted Ethernet port to remove
the PCB.
* The PCB should come free from the plastic housing, pull the bottom
(4 Ethernet ports) up as if you are opening a book.
* If done carefully, there is no need to remove the WiFi antenna connectors
to access the NAND flash.
* The TSOP48 NAND flash (U30, Spansion S34ML01G200TFV00) is located on the
opposite side of the PCB.
* To flash, you need to desolder the TSOP48 or use a 360 clip.
Installation:
The dumps to flash can be found in this repository:
https://github.com/halmartin/meraki-openwrt-docs/tree/main/mr30h
The device has the following flash layout (offsets with OOB data):
```
0x000000000000-0x000000100000 : "sbl1"
0x000000100000-0x000000200000 : "mibib"
0x000000200000-0x000000300000 : "bootconfig"
0x000000300000-0x000000400000 : "qsee"
0x000000400000-0x000000500000 : "qsee_alt"
0x000000500000-0x000000580000 : "cdt"
0x000000580000-0x000000600000 : "cdt_alt"
0x000000600000-0x000000680000 : "ddrparams"
0x000000700000-0x000000900000 : "u-boot"
0x000000900000-0x000000b00000 : "u-boot-backup"
0x000000b00000-0x000000b80000 : "ART"
0x000000c00000-0x000007c00000 : "ubi"
```
* Dump your original NAND (if using nanddump, include OOB data).
* Decompress `u-boot.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `u-boot` portion of NAND from
`0x738000`-`0x948000` (length `0x210000`). Offsets here include OOB data.
* Resolder the NAND after overwriting the `u-boot` regions.
OpenWrt Installation:
* After flashing NAND with the external programmer. Plug an Ethernet
cable into port 4. Power up the device.
* The new U-Boot build uses the space character `" "` (without quotes) to
interrupt boot.
* Interrupt U-Boot and `tftpboot` the OpenWrt initramfs image from your
tftp server
```
dhcp
setenv serverip <your_tftp>
tftpboot openwrt-ipq40xx-generic-meraki_mr30h-initramfs-uImage.itb
```
* Once booted into the OpenWrt initramfs, `scp` the `sysupgrade` image to
the device and run the normal `sysupgrade` procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Alternative installation steps if your device has U-Boot older than:
`U-Boot 2017.07-RELEASE-g78ed34f31579 (Sep 29 2017 - 07:43:44 -0700)`
**BIG FAT WARNING BEGIN**
Attmping to interrupt boot on a newer U-Boot release may permanently
brick your device! See: riptidewave93/LEDE-MR33#13
**BIG FAT WARNING END**
* Use `ubootwrite.py` from the above GitHub repository to transfer the
`u-boot.itb`
image to the router.
```
./ubootwrite.py --serial=/dev/ttyUSB0 --write u-boot.itb
```
* To avoid bricking your router, it is highly recommended at this point that
you flash the unlocked U-Boot to the `part.safe` ubi volume.
```
run set_ubi && ubi write $loadaddr part.safe 0x2fd48
```
* Power cycle the router. The stock Meraki U-Boot will boot `part.safe` which
is now the unlocked U-Boot.
* Use the new U-Boot build (`" "` to interrupt boot) to
`tftpboot` the OpenWrt initramfs image:
```
dhcp
setenv serverip <tftp_server_addr>
tftpboot openwrt-ipq40xx-generic-meraki_mr30h-initramfs-uImage.itb
bootm
```
* It is only recommended to flash U-Boot to the `u-boot` NAND region from
Linux:
```
insmod mtd-rw i_want_a_brick=1
```
* Copy `u-boot.elf` to the router:
```
scp -O u-boot.elf root@192.168.1.1:/tmp/
```
Note: If any of the below commands fails, YOU WILL HAVE A BRICK IF YOU
REBOOT OR LOSE POWER. Only a hardware programmer can recover the device.
```
flash_erase /dev/mtd8 0 0
nandwrite -p /dev/mtd8 /tmp/u-boot.elf
```
Note: ONLY use `u-boot.elf` when flashing the `u-boot` region (`/dev/mtd8`);
`u-boot.bin` or `u-boot.itb` will BRICK YOUR DEVICE
* `scp` the `sysupgrade` image to the device and run the normal `sysupgrade`
procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_mr30h-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17026
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for the Cisco Meraki Z3. The Z3 is a "teleworker"
device with 802.11ac and an integrated 5 port Gigabit switch.
Z3 hardware info:
* CPU: Qualcomm IPQ4029
* RAM: 512MB DDR3
* Storage: 128 MB (S34ML01G200TFV00)
* Networking: QCA8075 internal switch (5x 1GbE ports)
* WiFi: QCA4019 802.11b/g/n/ac
* USB: 1x USB3.0
* Serial: Internal header (J8, 2.54mm, populated)
Port 5 has POE output (802.3af). The Internet/WAN port is used for tftp booting
in U-Boot.
This device ships with secure boot, and cannot be flashed without
external programmers (TSOP48 NAND and I2C EEEPROM)!
Disassembly:
* Remove the four T8 screws on the bottom of the device under the rubber feet.
* Using a guitar pick or similar plastic tool, insert it on the side between
the bottom case and the side, pry up gently. The plastic bottom has several
latches around the perimeter (but none on the rear by the Ethernet ports).
* The TSOP48 NAND flash (U30, Spansion S34ML01G200TFV00) is located on the
bottom side of the PCB (facing you as you remove the bottom plastic).
To flash, you will need to desolder the TSOP48. Attempts to flash in-circuit
using a 360 clip were unsuccessful.
* The SOIC8 I2C EEPROM (U32, Atmel 24C64) is located on the bottom side of
the PCB (facing you as you remove the bottom plastic). It can be flashed in
circuit using a SOIC8 chip clip.
Installation:
The dumps to flash can be found in this repository:
https://github.com/halmartin/meraki-openwrt-docs/tree/main/z3_gx20
The device has the following flash layout (offsets with OOB data):
```
0x000000000000-0x000000100000 : "sbl1"
0x000000100000-0x000000200000 : "mibib"
0x000000200000-0x000000300000 : "bootconfig"
0x000000300000-0x000000400000 : "qsee"
0x000000400000-0x000000500000 : "qsee_alt"
0x000000500000-0x000000580000 : "cdt"
0x000000580000-0x000000600000 : "cdt_alt"
0x000000600000-0x000000680000 : "ddrparams"
0x000000700000-0x000000900000 : "u-boot"
0x000000900000-0x000000b00000 : "u-boot-backup"
0x000000b00000-0x000000b80000 : "ART"
0x000000c00000-0x000007c00000 : "ubi"
```
* Dump your original NAND (if using nanddump, include OOB data).
* Decompress `u-boot.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `u-boot` portion of NAND from
`0x738000`-`0x948000` (length `0x210000`). Offsets here include OOB data.
* Decompress `ubi.bin.gz` dump from the GitHub repository above (dump
contains OOB data) and overwrite the `ubi` portion of NAND from
`0xc60000`-`0x8400000` (length `0x77a0000`). Offsets here include OOB data.
* Dump your original EEPROM. Change the byte at offset `0x49` to `0x1e`
(originally `0x24`). Remember to re-write the EEPROM with the modified data.
* This can be done on Linux via the following command:
`printf "\x1e" | dd of=/tmp/eeprom.bin bs=1 seek=$((0x49)) conv=notrunc`
**Note**: the device will not boot if you modify the board major number and
have not yet overwritten the `ubi` and `u-boot` regions of NAND.
* Resolder the NAND after overwriting the `u-boot` and `ubi` regions.
OpenWrt Installation:
* After flashing NAND and EEPROM with external programmers. Plug an Ethernet
cable into the Internet/WAN port. Power up the device.
* The new U-Boot build uses the space character `" "` (without quotes) to
interrupt boot.
* Interrupt U-Boot and `tftpboot` the OpenWrt initramfs image from your
tftp server
```
dhcp
setenv serverip <your_tftp>
tftpboot openwrt-ipq40xx-generic-meraki_z3-initramfs-uImage.itb
```
* Once booted into the OpenWrt initramfs, created the `ART` ubivol with
the WiFi radio calibration from the mtd partition:
```
cat /dev/mtd10 > /tmp/ART.bin
ubimkvol /dev/ubi0 -N ART -s 524288
ubiupdatevol /dev/ubi0_1 /tmp/ART.bin
```
* `scp` the `sysupgrade` image to
the device and run the normal `sysupgrade` procedure:
```
scp -O openwrt-ipq40xx-generic-meraki_z3-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
ssh root@192.168.1.1 "sysupgrade -n /tmp/openwrt-ipq40xx-generic-meraki_z3-squashfs-sysupgrade.bin"
```
* OpenWrt should now be installed on the device.
Signed-off-by: Hal Martin <hal.martin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17026
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add IPQ Wifi entry for ath79 TP-Link Archer C59 v1.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20401
Signed-off-by: Robert Marko <robimarko@gmail.com>
It seems that adding Yuncore AX850 was missed during the board support,
and this breaks buildbots for ipq50xx with:
ERROR: unable to select packages:
ipq-wifi-yuncore_ax850 (no such package):
required by: world[ipq-wifi-yuncore_ax850]
make[4]: *** [/builder/shared-workdir/build/include/image.mk:396: target-dir-90b51871] Error 1
make[4]: *** Waiting for unfinished jobs....
So, add the required meta package.
Fixes: 5d2994a73e ("qualcommax: ipq50xx: Add support for Yuncore AX850")
Signed-off-by: Robert Marko <robimarko@gmail.com>
The IgniteNet SunSpot AC Wave2 comes with 2x QCA9994 ath10k chips
connected to the IPQ8068 SoC via PCIe.
Add board-2.bin for both radios on this board.
3ac4a64 qca9984: add BDFs for IgniteNet SS-W2-AC2600
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for Xiaomi AX6000.
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Etrontech EM6HE16EWAKG 512 MiB DDR3L-933
* Serial Port: 1v8 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax - up to 574 Mbps)
QCN9024 (4x4 5 Ghz 802.11an/ac/ax - up to 4804 Mbps)
QCA9887 (1x1 5 Ghz 802.11ac/n - up to 433 Mbps)
* Ethernet: IPQ5018 integrated virtual switch connected to:
- external QCA8337 switch (3 LAN Ports 10/100/1000)
- QCA8081 Phy WAN port (10/100/1000/2500)
* Flash: Either of:
- Gigadevice GD5F1GQ4RE9IGD (128 MiB)
- ESMT F50D1G41LB (128 MiB)
* LEDs: 1x WLAN Link (GPIO 23 Active High)
1x System Blue (GPIO 24 Active High)
1x System Yellow (GPIO 25 Active High)
1x WAN Link Blue (GPIO 26 Active High)
1x WAN Link Yellow (GPIO 27 Active High)
1x Green - Unused(GPIO 28 Active High)
3x LAN Phy Green
1x WAN Phy Green
* Buttons: 1x Reset (GPIO 38 Active Low)
Known issue:
- QCA9887 doesn't come up (possibly due to 1-lane PCIe phy not coming up or missing method to drive power),
hence the host PCIe controller is disabled in the DTS.
Flash instructions:
Download XMIR Patcher: https://github.com/openwrt-xiaomi/xmir-patcher
First flash a ubinized OpenWrt initramfs that will serve as the intermediate step, since
OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for
packages, through either of the below two methods:
Installation via XMIR Patcher:
1. Load the initramfs image: openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi
Installation via ubiformat method, through SSH:
1. If needed, enable SSH using XMIR Patcher.
2. Copy the file openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi to the /tmp directory
3. Open an SSH shell to the router
4. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
5. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd18 and mtd19 are the correct indexes from above!
6. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
7. Reboot the device by:
reboot
Continue in order to pernamently flash OpenWrt:
1. Upload the sysupgrade image to /tmp/ using SCP:
scp -O <path to image> root@192.168.1.1:/tmp/
2. Open an SSH shell to 192.168.1.1 from a PC within the same subnet
3. Use sysupgrade to flash the sysupgrade image:
sysupgrade -n -v /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19004
Signed-off-by: Robert Marko <robimarko@gmail.com>
5be4c60a9084 ipq5018: add BDF for Xiaomi AX6000
22588512b844 qcn9074: add BDF for Xiaomi AX6000
4810aacf3b1c qca9889: add BDF for Xiaomi AX6000
Signed-off-by: Robert Marko <robimarko@gmail.com>
I-O DATA WN-DAX3000GR is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based
on IPQ5018.
Specification:
- SoC : Qualcomm IPQ5018
- RAM : DDR3 512 MiB
- Flash : SPI-NAND 128 MiB (Macronix MX35UF1G24AD-Z4I)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm IPQ5018 (SoC)
- 5 GHz : Qualcomm Atheros QCN6102
- Ethernet : 5x 10/100/1000 Mbps
- wan (phy) : Qualcomm IPQ5018 (SoC)
- lan (switch) : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO): 7x/5x
- UART : through-hole on PCB (J3)
- assignment : 3.3V, TX, RX, NC, GND from tri-angle marking
- settings : 115200n8
- USB : USB 2.0 Type-A (through-hole on PCB, "J6")
- Power : 12 VDC, 1A (Typ. 930 mA)
Flash instruction using factory.bin image:
1. Boot WN-DAX3000GR with router mode
2. Access to the WebUI ("http://192.168.0.1/") on the device and open
the firmware update page ("ファームウェア")
3. Select the OpenWrt factory.bin image and click update ("更新") button
4. Wait ~120 seconds to complete flashing
Switching to the stock firmware:
1. Load the elecom.sh script
. /lib/upgrade/elecom.sh
2. Check the current index of rootfs
bootconfig_rw_index 0:bootconfig rootfs
3. Set the index to inverted value
bootconfig_rw_index 0:bootconfig rootfs <value>
bootconfig_rw_index 0:bootconfig1 rootfs <value>
example:
- step2 returned "0":
bootconfig_rw_index 0:bootconfig rootfs 1
bootconfig_rw_index 0:bootconfig1 rootfs 1
- step2 returned "1":
bootconfig_rw_index 0:bootconfig rootfs 0
bootconfig_rw_index 0:bootconfig1 rootfs 0
4. Reboot
Partition Layout (Stock FW, bootconfig(rootfs)=1):
0x000000000000-0x000000080000 : "0:SBL1"
0x000000080000-0x000000100000 : "0:MIBIB"
0x000000100000-0x000000140000 : "0:BOOTCONFIG"
0x000000140000-0x000000180000 : "0:BOOTCONFIG1"
0x000000180000-0x000000280000 : "0:QSEE"
0x000000280000-0x000000380000 : "0:QSEE_1"
0x000000380000-0x0000003c0000 : "0:DEVCFG"
0x0000003c0000-0x000000400000 : "0:DEVCFG_1"
0x000000400000-0x000000440000 : "0:CDT"
0x000000440000-0x000000480000 : "0:CDT_1"
0x000000480000-0x000000500000 : "0:APPSBLENV"
0x000000500000-0x000000640000 : "0:APPSBL"
0x000000640000-0x000000780000 : "0:APPSBL_1"
0x000000780000-0x000000880000 : "0:ART"
0x000000880000-0x000000900000 : "0:TRAINING"
0x000000900000-0x000003c40000 : "rootfs_1"
0x000003c40000-0x000003fc0000 : "Config"
0x000003fc0000-0x000007300000 : "rootfs"
0x000007300000-0x000007680000 : "Config_2"
0x000007680000-0x000007700000 : "idmkey"
0x000007700000-0x000007c00000 : "Reserved"
0x000007c00000-0x000007c80000 : "FWHEADER"
0x000007c80000-0x000007d00000 : "Factory"
Known Issues:
- This device has a Macronix MX35UF1G24AD SPI-NAND chip registered as
oobsize=128 in Linux Kernel. But using BCH8 breaks I/O on the chip
with the following errors, so this support uses BCH4 instead.
[ 1.542261] 0x000000480000-0x000000500000 : "0:appsblenv"
[ 1.547959] 1 fixed-partitions partitions found on MTD device 0:appsblenv
[ 1.551265] Creating 1 MTD partitions on "0:appsblenv":
[ 1.558096] 0x000000000000-0x000000040000 : "env-data"
[ 1.627282] u-boot-env-layout 79b0000.qpic-nand:flash@0:partitions:partition-0-appsblenv:partition@0:nvmem-layout: probe with driver u-boot-env-layout failed with error -74
root@OpenWrt:~# strings /dev/mtdblock10
[ 77.806720] mtdblock: MTD device '0:appsblenv' is NAND, please consider using UBI block devices instead.
[ 77.807554] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
[ 77.815977] I/O error, dev mtdblock10, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0
[ 77.824721] I/O error, dev mtdblock10, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0
[ 77.834095] I/O error, dev mtdblock10, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[ 77.843278] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 77.851577] Buffer I/O error on dev mtdblock10, logical block 0, async page read
Notes:
- This device has dual-boot feature and it's managed by the index in the
0:bootconfig and 0:bootconfig1 partitions.
- There are through-holes on PCB for USB 2.0, but it cannot be accessed
without disassembly of the housing. So it's not enabled in this
support.
- WN-DAX3000GR has the "bt_fw" volume in the firmware UBI in addition to
the volumes that will be removed in the section of ELECOM WRC-X3000GS2
in /lib/upgrade/platform.sh.
That volume is unnecessary for OpenWrt and add
`remove_oem_ubi_volume bt_fw` to remove that volume when sysupgrade.
(that function doesn't anything without errors if no specified volume)
MAC Addresses:
LAN : 50:41:B9:xx:xx:64 (0:APPSBLENV, "ethaddr"/"eth1addr" (text))
WAN : 50:41:B9:xx:xx:66 (0:APPSBLENV, "eth0addr" (text))
2.4 GHz: 50:41:B9:xx:xx:64 (0:APPSBLENV, "wifi0" (text))
5 GHz : 50:41:B9:xx:xx:65 (0:APPSBLENV, "wifi1" (text))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19053
Signed-off-by: Robert Marko <robimarko@gmail.com>
ALFA Network AP120C-AX is a dual-band ceiling AP, based on Qualcomm
IPQ6000 + QCN5021 + QCN5052 + QCA8072 chipsets bundle.
Specifications:
- SOC: Qualcomm IPQ6000 (quad-core Cortex-A53 1.2 GHz)
- DRAM: DDR3 512 MB (Micron MT41K256M16TW-107)
- Flash: 16 MB SPI NOR (Macronix MX25U12832F, boot device)
128 MB NAND (Macronix MX30UF1G18AC, dual-firmware)
- Ethernet: 2x 10/100/1000 Mbps Ethernet (QCA8072)
802.3at/af PoE input in WAN port
- Wi-Fi: 2x2 2.4 GHz Wi-Fi 6 (QCN5021 + RFFM8227 FEM)
2x2 5 GHz Wi-Fi 6 (QCN5152 + QPF4568 FEM)
- Antenna: for indoor version: dual-band, internal
2x (or 4x) U.FL antenna connectors on the PCB
- LED: for indoor/outdoor versions: 5x on external module (status,
2x Wi-Fi, 2x Ethernet), PoE LED on-board
8-pin on-board header for LED module (1.27 mm pitch, J14)
- Button: 1x button (reset)
- USB: 1x 4-pin on-board header for USB 2.0 (2.54 mm pitch, J22)
- UART: 1x micro USB Type-B for system console (Holtek HT42B534)
1x 4-pin on-board header (2.54 mm pitch, J11)
- Power: 802.3at/af PoE or 12 V DC/2 A (DC jack)
- Other: 8-pin and 4-pin on-board headers for external Bluetooth
module (1.27 mm pitch, J15, J16, unavailable, thus untested)
MAC addresses:
- WAN: 00:c0:ca:xx:xx:6c (art 0x0, device's label -2)
- LAN: 00:c0:ca:xx:xx:6d (art 0x6, device's label -1)
- 2.4 GHz (IPQ6000): 00:c0:ca:xx:xx:6e (art 0xc, device's label)
- 5 GHz (IPQ6000): 00:c0:ca:xx:xx:6f (device's label + 1)
Flash instructions:
Due to the lack of direct GUI based update capability and dual-firmware
partition configuration, it is recommended to use TFTP + serial console
based approach (console is available in micro USB connector):
1. Set a static IP 192.168.1.1/24 on PC and start TFTP server with the
'...-factory.ubi' image renamed to 'firmware.bin'.
2. Make sure you can access board's serial console over micro USB.
3. Power up the device, hit any key to enter U-Boot CLI and issue below
commands.
3.1 Restore U-Boot's environment to default values (double check first
the '0:APPSBLENV' partition offset using 'smem' command):
sf probe
sf erase 0x510000 0x10000
saveenv
3.2 Download and install OpenWrt in both partitions and reset the board:
tftpb 0x44000000 firmware.bin
flash rootfs
flash rootfs_1
reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
TP-Link EAP625-Outdoor HD is a 802.11ax AP claiming AX1800 support.
It is wall or pole mountable, and rated for outdoor use. It can only
be powered via PoE.
Hardware-wise, it is very similar to the older EAP610-Outdoor model.
Software-wise, I couldn't find a difference other than the board
data files, and device name. For this reason, the majority of the
devicetree from the EAP610-Outdoor is reused.
This device currently comes in a "v1", and "v1.6" version. The
"support-list" of the vendor firmware does not have a distinction
between these versions. This commit was tested on a 'V1.6" device.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512 MB
* Storage: 128MB NAND
* Ethernet:
* Gigabit RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Multi-color System LED (Green/Amber)
* Buttons:
* 1x Reset
* UART: 4-pin unpopulated header
* 1.8 V level, Pinout 1 - TX, 2 - RX, 3 - GND, 4 - 1.8V
Installation:
=============
Web UI method
-------------
Set up the device using the vendor's web UI. After that go to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
The connect to the machine via SSH:
ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
Disable signature verification:
cliclientd stopcs
Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
* Go to System -> Firmware Update.
* Under "New Firmware File", click "Browse" and select the image
* Select "Update" and confirm by clicking "OK".
If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWRT.
NOTE: If ssh continues to complain that "no matching host key type
found. Their offer: ssh-rsa,ssh-dss" it likely means that yor distro
has completely disabled deprecated siphers in ssh. In that case, run
the ssh command from a docker container of an older distro.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot tplink_eap625-outdoor-hd-v1-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the commandline.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18584
Signed-off-by: Robert Marko <robimarko@gmail.com>
ELECOM WRC-X3000GS2 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
IPQ5018.
Specification:
- SoC : Qualcomm IPQ5018
- RAM : DDR3 256 MiB (Zentel A3T2GF40CBF-HP)
- Flash : SPI-NAND 128 MiB (Macronix MX35UF1G24AD-Z4I)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm IPQ5018 (SoC)
- 5 GHz : Qualcomm Atheros QCN6102
- Ethernet : 5x 10/100/1000 Mbps
- wan (phy) : Qualcomm IPQ5018 (SoC)
- lan (switch) : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO): 8x/3x
- UART : through-hole on PCB, 4pins near the barcode
- assignment : 3.3V, TX, RX, NC, GND from the barcode side
- settings : 115200n8
- Power : 12 VDC, 1 A (Max. 11.5W)
Flash instruction using initramfs-factory.bin image:
1. Boot WRC-X3000GS2 normally with router mode
2. Access to the WebUI ("http://192.168.2.1/") on the device and open
the firmware update page ("ファームウェア更新")
3. Select the OpenWrt factory.bin image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing
Switching to the stock firmware:
1. Load the elecom.sh script
. /lib/upgrade/elecom.sh
2. Check the current index of rootfs
bootconfig_rw_index 0:bootconfig rootfs
3. Set the index to inverted value
bootconfig_rw_index 0:bootconfig rootfs <value>
bootconfig_rw_index 0:bootconfig1 rootfs <value>
example:
- step2 returned "0":
bootconfig_rw_index 0:bootconfig rootfs 1
bootconfig_rw_index 0:bootconfig1 rootfs 1
- step2 returned "1":
bootconfig_rw_index 0:bootconfig rootfs 0
bootconfig_rw_index 0:bootconfig1 rootfs 0
4. Reboot
Partition Layout (Stock FW):
0x000000000000-0x000000080000 : "0:SBL1"
0x000000080000-0x000000100000 : "0:MIBIB"
0x000000100000-0x000000140000 : "0:BOOTCONFIG"
0x000000140000-0x000000180000 : "0:BOOTCONFIG1"
0x000000180000-0x000000280000 : "0:QSEE"
0x000000280000-0x000000380000 : "0:QSEE_1"
0x000000380000-0x0000003c0000 : "0:DEVCFG"
0x0000003c0000-0x000000400000 : "0:DEVCFG_1"
0x000000400000-0x000000440000 : "0:CDT"
0x000000440000-0x000000480000 : "0:CDT_1"
0x000000480000-0x000000500000 : "0:APPSBLENV"
0x000000500000-0x000000640000 : "0:APPSBL"
0x000000640000-0x000000780000 : "0:APPSBL_1"
0x000000780000-0x000000880000 : "0:ART"
0x000000880000-0x000000900000 : "0:TRAINING"
0x000000900000-0x000003c40000 : "rootfs"
0x000003c40000-0x000003fc0000 : "Config"
0x000003fc0000-0x000007300000 : "rootfs_1"
0x000007300000-0x000007680000 : "Config_2"
0x000007680000-0x000007b80000 : "Reserved"
0x000007b80000-0x000007c00000 : "FWHEADER"
0x000007c00000-0x000007c80000 : "Factory"
Known Issues:
- All Wi-Fi related peripherals are disabled.
This device has only 256 MiB RAM and it's too few for ath11k. To
prevent OOM when using LuCI or other softwares, disable Wi-Fi related
peripherals in device tree at the moment.
- This device has a Macronix MX35UF1G24AD SPI-NAND chip registered as
oobsize=128 in Linux Kernel. But using BCH8 breaks I/O on the chip
with the following errors, so this support uses BCH4 instead.
root@OpenWrt:~# strings /dev/mtdblock10
[26427.133154] mtdblock: MTD device '0:appsblenv' is NAND, please consider using UBI block devices instead.
[26427.134125] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 2
[26427.142240] I/O error, dev mtdblock10, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 2
[26427.151427] I/O error, dev mtdblock10, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 2
[26427.160440] I/O error, dev mtdblock10, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[26427.169619] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[26427.178083] Buffer I/O error on dev mtdblock10, logical block 0, async page read
Notes:
- This device has dual-boot feature and it's managed by the index in the
0:bootconfig and 0:bootconfig1 partitions.
MAC Addresses:
LAN : 38:97:A4:xx:xx:60 (0:APPSBLENV, "eth1addr"/"ethaddr" (text))
WAN : 38:97:A4:xx:xx:63 (0:APPSBLENV, "eth0addr" (text))
2.4 GHz: 38:97:A4:xx:xx:61 (0:APPSBLENV, "wifi0" (text))
5 GHz : 38:97:A4:xx:xx:62 (0:APPSBLENV, "wifi1" (text))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18543
Signed-off-by: Robert Marko <robimarko@gmail.com>
The TP-link Deco X80-5G is a AX WIFI router with a single 1G (LAN) and 1 2.5G (WAN) port with a built in Quectel 5G modem.
Specifications:
Architecture ARMv8-A (aarch64 Cortex A53, 4 cores)
Vendor Qualcomm
Bootloader U-Boot (2016)
System-On-Chip Qualcomm IPQ8074A (Networking Pro 1210 platform)
CPU/Speed 2.2GHZ
Flash-Chip ESMT F59D1G81MB-45TI 1G-bit NAND
Flash MB 128MB (1Gbit)
RAM-chip 2* ESMT M15T4G16256A-DEBG2G 2Gb DDR3L (32bit)
RAM MB 512MB (4Gbit)
WLan System-On-Chip (5g) Qualcomm QCN5054
WLan Front end modules (5g) 8* Qorvo QPF4588
WLAN (5G) A/N/AC/AX
WLAN Antenna (int) 8* (4 shared with 2.5G)
WLan System-On-Chip (2.4G) Qualcomm QCN5024
WLan Front end modules (2.4G) 4* Skyworks SKY85340-11
WLAN (2.4G) B/G/N/AX
WLAN Antenna (int) 4* (shared with 5g)
Eithernet-phy (1Gbit) Qualcomm (Atheros) AR8033-AL1A
Ethernet (1Gbit) 1*
Eithernet-phy (2.5Gbit) Qualcomm QCA8081
Ethernet (2.5Gbit) 1*
Switch Embedded in the SOC?
Serial 1.8v 8n1 (testpoints)
Modem System-On-Chip Qualcomm 5G RG50xQ (Snapdragon X55 platform)
5G modem capability 5000Mbps down 900Mbps up
5G modem bands N1/N3/N5/N7/N8/N20/N28/N38/N40/N41/N77/N78/N79
4G modem capability 4.5G LTE-Advanced Pro (Cat20 down 2Gbps) (Cat18 up 200Mbps)
4G modem FDD bands B1/B3/B5/B7/B8/B18/B19/B20/B26/B28
4G modem TDD bands B34/B38/B39/B40/B41/B42/B43
Modem antenna (int) 8* (5G/4G use)
Modem antenna (ext) 2* SMA connectors (5G/4G use)
SIM type 1* Nano SIM
Telephony 1* POTS RJ11
(see wiki for more info:)
https://openwrt.org/inbox/toh/tp-link/x80-5g_v1
Notes:
Installation Instructions:
Between antennas 7 and 8 on the PCB with the RGB harness there are three test pads labelled TP1 TP2 and TP3 connections are as follows:
|TP2|-- RX
|TP1|-- TX
|TP3|-- GND
RX requires an external pullup to operate somewhere around 5 K ohm but your luck may vary the Uart is 1.8v
Set a static IP and set up a tftpserver and terminal.
power the router and quickly type the magic string “tpl” and press enter to break into u-boot
in the shell set the environment variables to enable tftp booting
setenv ipaddr (routerIP)
setenv serverip (server IP)
load you initramfs:
tftpboot 0x44000000 (serverIP):openwrt-qualcommax-ipq807x-tplink_x80-5g-initramfs-uImage.itb
boot your initramfs
bootm
upload your factory image to /tmp
format and install the factory image:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-qualcommax-ipq807x-tplink_x80-5g-squashfs-factory.ubi
Note as this device swaps root partitions upon update your boot partition may be set as mtd13
Update script to mount factory tplink partition's for MAC recovery and device data.
Capture Labelmac from Factory_data partition.
Patch LAN from Labelmac.
Patch ART from Labelmac.
Set GPIO to make modem operational from boot.
GPIO fan tables work like the stock device with three fan maps high active idle with a top fan speed of 6800 RPM.
High temp 70 deg speeds 6-8
Active temp 50 deg speeds 2-5
low temp 25 degree speed 0-1
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/16329
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for GL.iNET (AX3000) B3000.
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Winbond W634GU6NQB-11 (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
* Wi-Fi: QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (3 Ports 10/100/1000 GBASE-T)
* Flash: Winbond W25N01GWZEIG (128 MiB)
* LEDs: 1x single-color blue LED (GPIO 24 Active High)
1x single-color white LED (GPIO 23 Active High)
* Buttons: 1x Reset (GPIO 27 Active Low)
Flash Instructions:
*** The .img files are now universal ! ***
Openwrt --> openwrt-qualcommax-ipq50xx-glinet_gl-b3000-squashfs-factory.img
GL.iNet OEM --> openwrt-b3000-4.5.18-0731-1722397535.img
Either file can be flashed, in any of the available upgrade options, in both Firmwares.
Pick a file .. pick a method .. and SEND IT !!
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17903
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
* SoC: Qualcomm IPQ6018 (64-bit Quad-core Arm Cortex-A53 @ 1800MHz)
* Memory: 1 GiB
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN9074 (4x4 5 GHz 802.11ax)
* Wi-Fi: IPQ6018 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: RTL8211F (10/100/1GBASE-T)
* Flash: ESMT F59D1G81MB (128 MiB)
* LEDs: 1x Green Status (GPIO 37 Active High), 1x Yellow Status (GPIO 32
Active High) and an LED global control GPIO (GPIO 36 Active High, set
up by U-Boot)
* Buttons: 1x Reset (GPIO 9 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to the pads near T32 and T31.
2. Connect 3V3 TTL port to TX, RX, and GND, which are pad T31, T32 and
the pad near T31 respectively. Be sure not to connect VCC and
crossover TX and RX.
3. Copy RAM firmware image
openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb
to TFTP server root, available at 192.168.0.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# setenv serverip 192.168.0.1
# setenv ipaddr 192.168.0.99
# tftpboot 0x44000000 openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18389
Signed-off-by: Robert Marko <robimarko@gmail.com>
Netgear WAX610 / WAX610Y is a 802.11ax AP claiming AX1800 support.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512MB
* Storage: Winbond W29N01HZBINF 128MB NAND
* Ethernet:
* 2.5GbE RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Power: Dual-color LED (Green / Orange), Single-color LED (Blue)
* Ethernet: Dual-color LED (Green / Orange)
* 2.4Ghz WiFi: 2x Single-color LED (Blue, Green)
* 5Ghz WiFi: 2x Single-color LED (Blue, Green)
* Buttons:
* 1x Reset
* UART: 4-pin populated header
* Pinout 1 - VCC, 2 - GND, 3 - TX, 4 - RX
Installation:
=============
Web UI method
-------------
Set up the device using the stock web UI in local management mode.
Download the ui-factory.tar image.
* Enter the Management tab
* Select Maintenance->Upgrade->Firmware Upgrade
* Ensure the "Upgrade Options" field has "Local" selected
* Click "Browse File" and select the image
* Click "Upgrade" (NOT "Upgrade Now") at the bottom of the page
The device will install the image but reboot back into the vendor
firmware. Return the to Firmware Upgrade page as above and select
"Boot up Backup Firmware". The device should reboot into OpenWRT.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot netgear_wax610-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the command line.
Signed-off-by: Erik Servili <serverror@serverror.com>
Link: https://github.com/openwrt/openwrt/pull/18377
Signed-off-by: Robert Marko <robimarko@gmail.com>
Codename: Divo
Hardware specification:
========
SoC: Qualcomm IPQ6018
RAM: 512MB (2x ESMT 256MB DDR3L M15T2G16128A–DEBG2R)
NAND Flash: 512MB (Macronix MX30UF4G18AC or SK Hynix H27S4G8F2EDA-BC)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C-B0)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4@20/40/160 MHz (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 2x2@20/40/80 MHz (Qualcomm QCN5052 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 2x2@20/40 MHz (Qualcomm QCN5022 + Skyworks SKY8340-11)
IoT: Bluetooth 5 (CSR8811) - not implemented
LED: 1x RGB status + USB Blue (PWM)
USB: 1x USB 3.0
Button: WPS, Reset
Flash instructions (Without Serial):
========
Open Linksys Web UI - http://192.168.1.1/ca or http://linksysxxxxx.lan/ca depending on your setup.
xxxxx is the last 5 digits from the SN found on a sticker under the device.
Click on the Linksys Logo to by-pass smart app registration.
Login with your admin password. The default password can be found on the same sticker.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
Flash instructions (With Serial):
========
1. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd13 0 0
- nandwrite -p /dev/mtd13 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd15 0 0
- nandwrite -p /dev/mtd15 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel
2. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware:
- mtd -e kernel -n write FW_MR7500_1.1.12.211919_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MR7500_1.1.12.211919_prod.img alt_kernel
4. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
AQR firmware:
========
0. Firmware extracting:
To extract the firmware, use unblob (unblob.org)
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
2. Firmware updating:
Newer firmware (AQR114C.cld) is available in the latest OEM firmware (https://downloads.linksys.com/support/assets/firmware/FW_MR7500_1.1.12.211919_prod.img).
Copy AQR114C.cld to /lib/firmware/marvell
Link: openwrt#17428
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
SoC: Qualcomm IPQ6000
RAM: 512 MiB
Flash: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: 2.4GHz 802.11b/g/n/ax 2x2
WLAN2: 5GHz 802.11a/n/ac/ax 2x2
Button: Reset, Switch
USB: 1x 3.0
SD slot: 1 in GL-AXT1800
Install via stock firmware:
Upload factory.bin in stock firmware's upgrade page,
do not preserve settings.
Install via uboot web failsafe:
Push the reset button for 5 seconds, then use broswer
to access http://192.168.1.1, and upload factory.ubi.
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
PKG_MIRROR_HASH is incorrect and the package check is currently failing.
Fixes: 4990ce613b ("ipq-wifi: update to 2024-02-17")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add support for Linksys MR5500 (Hydra 6 Pro).
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Kingston D2516ECMDXGJD (512 MiB)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
QCN9024 (4x4:4 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (4 Ports 10/100/1000 GBASE-T)
* Flash: Gigadevice GD5F2GQ5REYIH (256 MiB)
* LEDs: 1x multi-color PWM LED
1x blue led for USB (GPIO 19 Active High)
* Buttons: 1x WPS (GPIO 27 Active Low)
1x Reset (GPIO 28 Acive Low)
5x ethernet port LEDs (amber for activity & green for link up)
* Peripherals: 1x USB2 (powered by GPIO 17 Active Low)
support for USB3 will be added in a separate PR
* FCC ID: 2AYRA-03734
Flash instructions:
1. On OEM firmware, login to the device (typically at http://192.168.1.1) and click 'CA'
in the bottom right corner -> Connectivity -> Manual Upgrade. Alternatively, browse to
http://<router IP>/fwupdate.html.
Upgrade firmware using openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin image.
Optionally install on second partition, after first boot check actual partition:
fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin kernel
and in case of 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
fw_printenv -n boot_part
In case of 2:
flash_erase /dev/mtd12 0 0
nandwrite -p /dev/mtd12 openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin
or in case of 1:
flash_erase /dev/mtd14 0 0
nandwrite -p /dev/mtd14 openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin
After first boot install firmware on second partition:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin kernel
or:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware.
Download firmware from OEM website:
MR5500: https://support.linksys.com/kb/article/207-en/
From serial or SSH:
fw_printenv boot_part
in case of 1:
mtd -r -e alt_kernel -n write FW_MR5500_1.1.2.209598_prod.img alt_kernel
else in case of 2:
mtd -r -e kernel -n write FW_MR5500_1.1.2.209598_prod.img kernel
4. Boot from USB
This allows you loading an OpenWrt image into RAM and is meant for recovery scenarios only.
Enable loading image from USB in u-boot. From serial or SSH:
fw_setenv bootusb 'usb start && usbboot &loadaddr && bootm $loadaddr'
fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
Copy OpenWrt initramfs image to USB:
dd bs=1M if=openwrt-qualcommax-ipq50xx-linksys_mr5500-initramfs-uImage.itb of=/dev/sda
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17958
Signed-off-by: Robert Marko <robimarko@gmail.com>
The SPNMX56 is an ISP-branded and distributed device similar to the MX5500
with the same Wifi chips (IPQ5018 for 2.4G and QCN9074 for 5G) but has an
additional QCA8081 PHY providing a 2.5gbps ethernet WAN port.
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Winbond W634GU6NB-11 (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
QCN9024 (4x4:4 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (3 Ports 10/100/1000 GBASE-T) and a
QCA8081 phy (up to 2.5 Gbps)
* Flash: Gigadevice GD5F2GM7RExxG (256 MiB)
* LEDs: 1x multi-color PWM LED
* Buttons: 1x WPS (GPIO 27 Active Low)
1x Reset (GPIO 28 Acive Low)
Flash instructions:
1. On OEM firmware, login to the device (typically at http://192.168.1.1)
and click 'CA' in the bottom right corner -> Connectivity ->
Manual Upgrade. Alternatively, browse to http://<router IP>/fwupdate.html
Upload openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin
Optionally flash 2nd partition, after first boot check actual partition:
fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin kernel
and in case of 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware
hit Enter once booted and enter credentials (login: root, password: admin)
fw_printenv -n boot_part
In case of 2:
flash_erase /dev/mtd12 0 0
nandwrite -p /dev/mtd12 openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin
or in case of 1:
flash_erase /dev/mtd14 0 0
nandwrite -p /dev/mtd14 openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin
After first boot install firmware on second partition:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin kernel
or:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware.
Download firmware from OEM website:
Firmware for this device cannot be searched for on the Linksys website.
Instead, we'd have to use serial to intercept the URL of the firmware
while it's trying to update. Firmware is ISP specific:
Toob (UK): http://download.linksys.com/updates/20241125t080737/FW_MX56TB_1.0.1.216218_prod.img
The intention is to collect URLs for different ISPs on a wiki page.
From serial or SSH:
fw_printenv boot_part
in case of 1:
mtd -r -e alt_kernel -n write FW_MX56TB_1.0.1.216218_prod.img alt_kernel
else in case of 2:
mtd -r -e kernel -n write FW_MX56TB_1.0.1.216218_prod.img kernel
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17968
Signed-off-by: Robert Marko <robimarko@gmail.com>
Aliyun AP8220 is an AP manufactured by Edgecore.
(Very similar to Edgecore EAP102)
Hardware specifications:
SoC: Qualcomm IPQ8071A
RAM: 1GB of DDR4 600MHz
Flash1: MX25U3235F 4MB
Flash2: MX30UF1G18AC 128MB
Ethernet: 2x 2.5G RJ45 port
USB: 2x USB-A 2.0 port
WiFi1: QCN5024 2.4GHz
WiFi2: QCN5054 5GHz
Power: DC 12V / PoE
Flash instructions:
1. Connect the router via serial port
2. Keep pressing @ until uboot is interrupted
3. Download the initramfs image, rename it to
initramfs.bin, host it with tftp server
4. Run these commands:
tftpboot initramfs.bin
bootm
5. After openwrt boots up, use scp or luci
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17970
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for Linksys MX2000 (Atlas 6) and MX5500 (Atlas 6 Pro).
These devices are completely identical except for the secondary wifi
chip used for 5Ghz: QCN6102 is used on MX2000 while QCN9024 is used
on MX5500
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Winbond W634GU6NB-11 (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
* Wi-Fi: MX2000: QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
MX5500: QCN9024 (4x4:4 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (4 Ports 10/100/1000 GBASE-T)
* Flash: Macronix MX35UF2GE4AD (256 MiB)
* LEDs: 1x multi-color PWM LED
* Buttons: 1x WPS (GPIO 27 Active Low)
1x Reset (GPIO 28 Acive Low)
Flash instructions (in case of MX2000, else replace with MX5500 images):
1. On OEM firmware, login to the device (typically at http://192.168.1.1) and click 'CA'
in the bottom right corner -> Connectivity -> Manual Upgrade. Alternatively, browse to
http://<router IP>/fwupdate.html.
Upgrade firmware using openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin image.
Optionally install on second partition, after first boot check actual partition:
fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin kernel
and in case of 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
fw_printenv -n boot_part
In case of 2:
flash_erase /dev/mtd12 0 0
nandwrite -p /dev/mtd12 openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin
or in case of 1:
flash_erase /dev/mtd14 0 0
nandwrite -p /dev/mtd14 openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin
After first boot install firmware on second partition:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin kernel
or:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware.
Download firmware from OEM website:
MX2000: https://support.linksys.com/kb/article/585-en/
MX5500: https://support.linksys.com/kb/article/587-en/
From serial or SSH:
fw_printenv boot_part
in case of 1:
mtd -r -e alt_kernel -n write FW_MX2000_1.1.7.210469_prod.img alt_kernel
else in case of 2:
mtd -r -e kernel -n write FW_MX2000_1.1.7.210469_prod.img kernel
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add ability to download and package ath11k firmware for QCN6122.
QCN6122 is specific/exclusive to the IPQ5018 platform and firmware
files are publishes in a subdirectory of the IPQ5018 firmware files.
While at it, add support for packaging BDFs for QCN6122 wifi and
update iwinfo to recognize QCN6122 wifi.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add ability to download and package ath11k firmware for IPQ5018.
As part of commit 172ccf7, the source is pointed to the new QCA repo.
Until QCA publishes updated firmware for IPQ5018 and QCN6122, we need
to download the firmware from the old QUIC repo. As such, add a new
download routine for IPQ5018/QCN6122 to fetch the firmware files from
the old repo.
While at it, add support for packaging BDFs for IPQ5018-based boards
and update iwinfo to recognize IPQ5018 wifi.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
TP-Link EAP610-Outdoor is a 802.11ax AP claiming AX1800 support. It is
wall or pole mountable, and rated for outdoor use. It can only be
powered via PoE.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512 MB
* Storage: ESMT PSR1GA30DT 128MB NAND
* Ethernet:
* Gigabit RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Multi-color System LED (Green/Amber)
* Buttons:
* 1x Reset
* UART: 4-pin unpopulated header
* 1.8 V level, Pinout 1 - TX, 2 - RX, 3 - GND, 4 - 1.8V
Installation:
=============
Web UI method
-------------
Set up the device using the vendor's web UI. After that go to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
The connect to the machine via SSH:
ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
Disable signature verification:
cliclientd stopcs
Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
* Go to System -> Firmware Update.
* Under "New Firmware File", click "Browse" and select the image
* Select "Update" and confirm by clicking "OK".
If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWRT.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot tplink_eap610-outdoor-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the commandline.
The tplink2022 image format
============================
The vendor images of this device are packaged in a format that does
not match any previous tplink formats. In order for flashing to work
from the vendor's web UI, firmware updates need to be packaged in
this format. The `tplink-mkimage-2022.py` is provided for this
purpose.
This script can also analyze vendor images, and extract the required
"support" string. This string is checked by the vendor firmware, and
images with a missing or incorrect string are rejected.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14922
Signed-off-by: Robert Marko <robimarko@gmail.com>
4b849214b137 ipq8074: add TP-Link EAP620 HD v1 BDF Add board file for TP-Link EAP620 HD v1. Sourced from bdwlan_US.bin in stock firmware 1.1.0 Build 20211028
Signed-off-by: Shymon Samsel <ssamsel@umass.edu>
Link: https://github.com/openwrt/openwrt/pull/17254
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 1.4 GHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCA5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (2x2 2.4 GHz 802.11b/g/n/ax)
* Ethernet: AR8031 (10/100/1000BASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2, and 3 respectively.
Be sure to crossover TX and RX.
3. Copy RAM firmware
openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb
to a TFTP server's root that is in the same subnet as your AP.
4. Power up the AP hold Ctrl+B in the serial console (115200n8) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# setenv serverip <TFTP server addr>
# setenv ipaddr <addr of AP>
# tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp -O openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Known Issues:
* 5GHz radio instability (upstream current ath11k build bug maybe?)
Device support directly followed from EAP660HDv1 support
Links: #15832
Signed-off-by: Shymon Samsel <ssamsel@umass.edu>
Link: https://github.com/openwrt/openwrt/pull/17254
Signed-off-by: Robert Marko <robimarko@gmail.com>
