The Zyxel NWA110AX is a dual band 2x2:2 802.11ax wireless access point
with PoE.
The device is very similar to the NWA210AX except for being 2x2 instead
of 4x4 in the 5GHz band and not having the 2.5GbE ethernet port. This
commit factors out a common DTS and device definition and reuses it for
both devices.
Hardware:
* SoC: Qualcomm IPQ8070A
* RAM: 1GiB 1x Samsung K4A8G165WC-BCTD
* Flash: 8MiB Winbond W25Q64DW SPI-NOR, 256MiB Winbond W29N02GZ SPI-NAND
* WLAN 2.4GHz: QCN5024 2x2:2 802.11b/g/n/ax
* WLAN 5GHz: QCN5054 2x2:2 802.11n/ac/ax
* Ethernet: 1x 1GbE with AR8033 PHY
* Serial Config: 3.3V TTL 115200-8-N-1, externally accessible
* Serial Layout: GND TX RX 3.3V (don't connect, marked with triangle)
* LEDs: 1x red, 1x green, 1x blue, 1x white
* Buttons: 1x reset
MAC addresses:
* Uplink: base address on label
* 2.4GHz WLAN: base + 1
* 5GHZ WLAN: base + 2
Flashing Notes:
The device uses a dual-image setup and OpenWrt can only be installed as
image 0. When the currently running stock firmware is image 0, OpenWrt
will be installed as image 1, fail to boot and the device returns to stock
firmware. If this happens, install any version of stock firmware so that
it runs as image 1, before installing OpenWrt. Alternatively, if there
already is a valid stock firmware in image 1, the "debug dual-image show"
and "debug dual-image set boot-image image1" commands can be used in the
stock CLI via serial/SSH/telnet to switch to image 1.
Flashing with Stock Web Interface:
* Get the OpenWrt factory image and rename it to a shorter name, for
example "openwrt.bin" (the stock firmware has a character limit)
* In the web interface, go to "Maintenance" -> "File Manager" ->
"Firmware Package" (or click the link next to "Firmware Version" under
"Device Information" on the dashboard)
* Under "Upload File" browse to the renamed OpenWrt factory image and
click on "Upload"
Switch Boot Image:
* OpenWrt to stock: "zyxel-bootconfig-ipq807x set image1"
* Stock to OpenWrt: "debug dual-image set boot-image image0"
Unbrick / Revert to Stock with the Boot Module:
* Disconnect the device from power
* Configure your machine to 192.168.1.103/24 and start a TFTP server
* Put the stock firmware image into the TFTP server root and rename it to
"ZLD-current"
* Establish a serial connection to the device through the console port
* Connect the device to power
* When prompted, press a key to abort automatic boot and enter debug mode
* Use the "atnz" command to flash the firmware image
* Use the "atgo" command to boot from the newly flashed image
Signed-off-by: Michael Lotz <mmlr@mlotz.ch>
Link: https://github.com/openwrt/openwrt/pull/21849
Signed-off-by: Robert Marko <robimarko@gmail.com>
ZTE MF833U1 is a LTE dongle that expose a cdc_ether interface for data link
and WebUI for management. It handles all the "modem" functionalities
internally and does not expose any serial interface. Instead it acts like a
"router in a stick".
It initially enumerates as a USB mass-storage device and does not bind any
network driver, so no netdev is created until a modeswitch is performed.
The test is done on Cudy TR3000 256MB v1.0 running OpenWrt 24.10.5 with an
unit targeting Chinese market:
- Hardware Version: MF883U1_V1.0.0
- Software Version: BD_MF883U1V1.0.0B06
- CMIT ID: 2019CP2106
There are report online that the device have different variants that have
different behavior across different firmware, HW revisions or SKUs.
Before the switch:
```
root@OpenWrt:~# lsusb -t
/: Bus 001.Port 001: Dev 001, Class=root_hub, Driver=xhci-mtk/1p, 480M
|__ Port 001: Dev 003, If 0, Class=[unknown], Driver=[none], 480M
root@OpenWrt:~# lsusb Bus 001 Device 001: ID 1d6b:0002 Linux 6.6.119
xhci-hcd xHCI Host Controller Bus 001 Device 004: ID 19d2:1705
DEMO,Incorporated DEMO Mobile Boardband Bus 002 Device 001: ID 1d6b:0003
Linux 6.6.119 xhci-hcd xHCI Host Controller ```
After the switch:
```
root@OpenWrt:~# lsusb -t
/: Bus 001.Port 001: Dev 001, Class=root_hub, Driver=xhci-mtk/1p, 480M
|__ Port 001: Dev 003, If 0, Class=[unknown], Driver=cdc_ether, 480M
|__ Port 001: Dev 003, If 1, Class=[unknown], Driver=cdc_ether, 480M
|__ Port 001: Dev 003, If 2, Class=[unknown], Driver=[none], 480M
/: Bus 002.Port 001: Dev 001, Class=root_hub, Driver=xhci-mtk/1p, 20000M/x2
root@OpenWrt:~# lsusb Bus 001 Device 001: ID 1d6b:0002 Linux 6.6.119
xhci-hcd xHCI Host Controller Bus 001 Device 003: ID 19d2:1706
DEMO,Incorporated DEMO Mobile Boardband Bus 002 Device 001: ID 1d6b:0003
Linux 6.6.119 xhci-hcd xHCI Host Controller ```
The following kernel debug log is presented:
``` cdc_ether 1-1:1.0 eth2: register 'cdc_ether' at usb-11200000.usb-1, ZTE
CDC Ethernet Device, 34:4b:50:00:00:00 ```
Signed-off-by: Zihao Diao <hi@ericdiao.com>
Link: https://github.com/openwrt/openwrt/pull/21867
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Allow callers of edit_create_destroy to pass additional named arguments
via info.named_args that get merged into the create command parameters.
Signed-off-by: John Crispin <john@phrozen.org>
Ensure md volumes are ready before attempting to mount volumes.
Signed-off-by: Joe Hohertz <jhohertz@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21553
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The module exists in ucode and has been present for a while
but has not been enabled. It provides the ucode zlib module
for handling gzip and zlib compression in ucode scripts.
The package is ~ 5Kb. Installed ~18Kb.
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21417
Signed-off-by: Robert Marko <robimarko@gmail.com>
libubus only completes pending requests when the socket receives EOF.
When explicitly disconnecting, we need to call ubus_flush_requests().
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It seems old website has been retired.
Signed-off-by: Yanase Yuki <dev@zpc.st>
Link: https://github.com/openwrt/openwrt/pull/21279
Signed-off-by: Robert Marko <robimarko@gmail.com>
It seems old website has been retired.
Signed-off-by: Yanase Yuki <dev@zpc.st>
Link: https://github.com/openwrt/openwrt/pull/21279
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some packages with variants did not specify the default among the
alternatives, so were left without any apk 'provider_priority'
for that package. This caused the apk solver to select the wrong
variant, silently changing the requested package list.
Notable among these were busybox, procd and the hostapd/wpad suite.
This behavior presented in the imagebuilders when creating the
image as follows, silently replacing packages even when explicitly
requested:
$ make image PACKAGES=busybox
...
( 14/148) Installing busybox-selinux (1.37.0-r6)
...
We add 'DEFAULT_VARIANT:=1' to the packages that were missing one,
providing apk with sufficient information to choose the correct
package.
See link below for further examples and discussion.
Link: https://github.com/openwrt/openwrt/pull/21288#issuecomment-3704101422
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21358
Signed-off-by: Robert Marko <robimarko@gmail.com>
Broadcom BCM43602 needs certain NVRAM variables to be set to function. Add
a quirk for it and add ASUS RT-AC3200 which has got Broadcom BCM43602 to
the quirk. Thanks to Tom Brautaset for finding the needed variables.
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
Add ASUS RT-AC3200 and ASUS RT-AC5300 to the set wireless LED behaviour
quirk. ASUS RT-AC3200's wireless chip is different than ASUS RT-AC5300's,
the environment variables for it are 0:ledbh10 and 1:ledbh10.
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
Fix wrong output using '%d' format when byte count parameter is not
given.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21013
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Zyxel NWA210AX is a wall- and ceiling-mountable access point (AP).
Hardware specifications:
- SoC: Qualcomm IPQ8071A
- RAM: 1 GB (Samsung K4A8G165WC-BCTD)
- Flash: 8 MB (Winbond W25Q64DW), 256 MB (Winbond W29N02GZ)
- Ethernet: 1x 2.5 Gbps RJ45 port (QCA8081), 1x 1 Gbps RJ45 port (AR8033)
- WiFi: 2.4 GHz 802.11ax/b/g/n (QCN5024), 5 GHz 802.11 ac/ax/n (QCN5054)
- Power: DC 12V/PoE 802.3at
- Button: Reset
- LEDs: Multicolour red/green/blue/white via LP5562
Installation/flashing instructions:
1. In OEM web interface navigate to gear icon → System → SSH and enable SSH.
2. Log in via SSH (username/password are the same as for the web interface).
3. Run "debug dual-image show".
4. Verify that output is "Current Image num: 1".
5. If this is not the case (i.e. if the output is "Current Image num: 0"):
a. Either flash a fresh version of factory firmware, or
b. run "debug dual-image set boot-image image1" and then run "reboot".
6. Log in via SSH again and verify that output is "Current Image num: 1".
7. Rename "openwrt-qualcommax-ipq807x-zyxel_nwa210ax-squashfs-factory.bin" to
"openwrt.bin" to avoid upload errors in the OEM web interface.
8. Reopen OEM web interface, navigate to wrench icon → File Manager →
Firmware Package and upload the bin file. Once the upgrade process is
finished and OpenWrt has booted, the LED will light up green.
Switching between OpenWrt and OEM firmware:
- OpenWrt → Zyxel via ssh command "zyxel-bootconfig-ipq807x set image1".
- Zyxel → OpenWrt via ssh command "debug dual-image set boot-image image0".
This commit is based on the work of Pascal Beleiu <pascal@beleiu.de>:
93ca21f3 (qualcommax: ipq807x: add support for Zyxel NWA210AX, 2025-03-17)
Signed-off-by: Eric Schäfer <eric@es86.de>
Link: https://github.com/openwrt/openwrt/pull/19828
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add TARGET_LDFLAGS to MYLDFLAGS make sure that the required flags are used
during the compilation.
Signed-off-by: Jonathan Luijsmans <jonathan.luijsmans_ext@softathome.com>
Link: https://github.com/openwrt/openwrt/pull/20642
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
313f344d8436 dlink-sge-image: add support for D-Link DIR-X1860 B1/DIR-X1550 A1
ac7a4abdde7d iptime-crc32: add support for ipTIME AX3000SE
c42a3bc53da8 iptime-crc32: add support for ipTIME AX2002MESH
Link: https://github.com/openwrt/openwrt/pull/20734
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
See announcement mail for list of new features:
https://lists.infradead.org/pipermail/linux-mtd/2025-February/108248.html
Cherry pick some upstream commits which fix build problems in some
situations.
autoreconf fixup is needed now otherwise the build fails with:
```
mtd-utils-2.3.0/missing: line 81: automake-1.16: command not found
```
The code in tests/ubifs_tools-tests/Makemodule.am does not build because
some test data is not packaged in the tar files, do not build code from
this directory.
The size increased only very little:
61498 bin/targets/ramips/mt7621/packages/nand-utils-2.3.0-r1.apk
101643 bin/targets/ramips/mt7621/packages/ubi-utils-2.3.0-r1.apk
61243 bin/targets/ramips/mt7621/packages/nand-utils-2.2.1-r1.apk
101291 bin/targets/ramips/mt7621/packages/ubi-utils-2.2.1-r1.apk
Link: https://github.com/openwrt/openwrt/pull/20540
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Edit CMakeLists.txt to fulfill cmake 4.0 requirement that
cmake_minimum_required is now at least 3.5 and in future 3.10.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/20265
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
AUTORELEASE has been deprecated from a long time. Drop it and hardcode
the release following the current one present in the downloads
repository.
Link: https://github.com/openwrt/openwrt/pull/20586
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
AUTORELEASE has been deprecated from a long time. Drop it and hardcode
the release following the current one present in the downloads
repository.
Link: https://github.com/openwrt/openwrt/pull/20586
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
AUTORELEASE has been deprecated from a long time. Drop it and hardcode
the release following the current one present in the downloads
repository.
Link: https://github.com/openwrt/openwrt/pull/20586
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add pending patch that disable libmagic support as this cause
reproducibility issue due to timing of presence of libmagic library at
times e2fsprogs gets compiled.
The new patch adds control on libmagic inclusion and we add the
--without-libmagic to the configure args by default.
Reported-by: Paul Spooren <mail@aparcar.org>
Link: https://github.com/openwrt/openwrt/pull/20499
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant patch for host build as this has been fixed in 1.44.1
but for some reason it wasn't notice with the patch directly refreshed
(with the fix right up)
Fixes: 198172c048 ("package/utils/e2fsprogs: update to 1.44.1")
Link: https://github.com/openwrt/openwrt/pull/20499
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
