This commit fixes stability issues on certain RAX3000Me devices. Some
devices has DDR3 RAM which don't able to work reliably at 2133 MHz
and require special BL2 (1866 MHz RAM freq).
Fixes: https://github.com/openwrt/openwrt/issues/20046
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20059
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The new profiles are intended for devices with DDR3 RAM which
don't able to work reliably at 2133 MHz.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20059
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Buffalo WSR-6000AX8 and AX8P models.
Hardware
--------
SOC: MediaTek MT7986B
RAM: 512MB
FLASH: 128MB SPI-NAND (Winbond)
WIFI 2.4G: (Embedded in SOC) b/g/n/ax, MIMO 4x4
WIFI 5G: (Embedded in SOC) a/n/ac/ax, MIMO 4x4
ETHERNET: 2.5GbE MaxLinear GPY211C (eth1: WAN)
ETHERNET: MediaTek MT7531AE 3xGbE (eth0: LAN1, LAN2, LAN3)
UART: 3.3V 115200 8N1
Serial(UART) Pin Layout
-----------------------
+-------+-------+-------+-------+
J4 | RX | TX | GND |(3.3V) |
+-------+-------+-------+-------+
(Bottom Side)
MAC Address Table
-----------------
lan1-3: board_data 0x4(text)
eth1/WAN: board_data 0x4(text)
WIFI 2.4G: lan1 + 2
WIFI 5G: lan1 + 9
Installation
------------
1. Set up a TFTP server with the IP address "192.168.11.2".
2. Rename the OpenWrt initramfs image to "linux.ubi-recovery" and place it
in the TFTP server's root directory.
3. While holding down the AOSS button, power on the WSR-6000AX8 (or AX8P).
4. The device will automatically download the initramfs image
from the TFTP server and boot into it.
5. Once booted, run "sysupgrade -n" using the OpenWrt sysupgrade image
to complete the installation.
Recovery
--------
1. Decrypt the official firmware image using "buffalo-enc".
example:
$ buffalo-enc -d -i wsr_6000ax8_jp_100 -o wsr_6000ax8_jp_100.dec \
-l -O 0xc8
2. Run "sysupgrade -F -n" with the decrypted image.
Signed-off-by: Shin Sato <shin.sugar.ssyysy2021@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/13107
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit add kernel module support for Infineon DPS310/DPS368/DPS422
digital barometric air pressure and temperature sensor.
Test on custom board based on Mediatek MT7988a.
Signed-off-by: Elwin Huang <s09289728096@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20101
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
of_gpio.h is deprecated in upstream Linux and may be removed soon. Get
ahead of things and remove it. Most of these drivers already use the
gpiod API.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20076
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is a smart door lock device equipped with OpenWrt 14.07 OEM
modified version Qdwrt
The OEM has closed down, This commit is intended to maximize the
remaining value of these devices. It can flash OpenWrt to become
an AP
Specification:
- SoC: MediaTek MT7628NN
- Flash: 8 MB
- RAM: 64 MB
- Power: DC 5V - 25V
- Ethernet: 1 x RJ45 (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only
- On-Board LED:
Status 1: GPIO/43 active-low
Status 2: GPIO/44 active-low
Power: AlwaysOn
- Button:
WPS / RESET: GPIO/14 active-low
- Bluetooth: CC2541 via UART1 (ttyS1) and GPIO/26-29
- RFID: MF RC522 on I2C@28
- RTC: DS1339 on I2C@68
- Shell (via CON1 cable)
- LED (Swipe card area):
- Green GPIO/3 active-high
- Red GPIO/11 active-high
- Matrix keypad: (active-low)
GPIO/20 GPIO/21 GPIO/19 (Rows)
GPIO/24 1 2 3
GPIO/25 4 5 6
GPIO/22 7 8 9
GPIO/23 BACK 0 ENTER
(Cols)
- UART: 1 x UART on PCB - 57600 8N1
- GPIO Relay: GPIO/42 active-high
- GPIO Buzzer: GPIO/15 active-high
Warning:
The original firmware does not use the device tree.
This device tree is written based on the content of /sys/devices/platform
and has been tested
Note:
- On the device, matrix keypad rows actually are columns, and the columns actually are rows
- The key code of the CLEAR key of the matrix keypad is BACK in the original firmware.
Issue:
- No drivers in mainline kernel for RFID and Bluetooth.
Flash Instruction:
Using SSH/Telnet:
1. Connect the board to the computer via RJ45 Ethernet
2. Login 10.10.10.1 with root password "szqdingnet123" (SSH Port 22, Telnet Port 9900)
3. Download openwrt firmware on the computer.
4. Setup a http server on computer. And use wget download openwrt firmware from computer
5. Use command "mtd -r write openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin firmware"
to flash
Using U-Boot WebUI:
1. Configure PC with a static IP address 10.10.10.2/24.
2. Open http://10.10.10.1
3. Use "mkqdimg -B qc202 -f openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin" to
make image.
4. Upload factory.bin via U-Boot WebUI.
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-qianding-smart-locker-and-flash.html
Original U-Boot firmware image tools:
https://gitlab.com/CoiaPrant/mkqdimg
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17471
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Make sure that the package gets updated after the last fix.
Fixes: cd20ae44f2 ("uqmi: fix data-format parsing")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
wda-get-data-format now returns an object instead of a single string.
Account for this change when reading the packet data format.
Suggested-by: Sebastian Ertz (https://github.com/sebastianertz)
Signed-off-by: David Bauer <mail@david-bauer.net>
The EN751221 has an XHCI that is compatible with MT7621.
While there is setup logic in the vendor code for both
EN751221 and MT7621, but MT7621 does not use it in mainline
or OpenWRT, and it appears to work correctly with EN751221.
Include SCSI / Mass Storage because many EcoNet devices
contain a builtin USB SD-Card reader.
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://github.com/openwrt/openwrt/pull/20050
[Remove usb storage kmod from smartfiber_xp8421-b]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
New upstream release. Debian changelog:
* New upstream microcode datafile 20250812 (closes: #1110983, #1112168)
- Mitgations for INTEL-SA-01249 (processor Stream Cache):
CVE-2025-20109: Improper Isolation or Compartmentalization in the
stream cache mechanism for some Intel Processors may allow an
authenticated user to potentially enable escalation of privilege via
local access. Intel also disclosed that several processors models
had already received this mitigation on the previous microcode
release, 20250512.
- Mitigations for INTEL-SA-01308:
CVE-2025-22840: Sequence of processor instructions leads to
unexpected behavior for some Intel Xeon 6 Scalable processors may
allow an authenticated user to potentially enable escalation of
privilege via local access.
- Mitigations for INTEL-SA-01310 (OOBM services module):
CVE-2025-22839: Insufficient granularity of access control in the
OOB-MSM for some Intel Xeon 6 Scalable processors may allow a
privileged user to potentially enable escalation of privilege via
adjacent access.
- Mitigations for INTEL-SA-01311 (Intel TDX):
CVE-2025-22889: Improper handling of overlap between protected
memory ranges for some Intel Xeon 6 processors with Intel TDX may
allow a privileged user to potentially enable escalation of
privilege via local access.
- Mitigations for INTEL-SA-01313:
CVE-2025-20053: Improper buffer restrictions for some Intel Xeon
Processor firmware with SGX enabled may allow a privileged user to
potentially enable escalation of privilege via local access.
CVE-2025-21090: Missing reference to active allocated resource for
some Intel Xeon processors may allow an authenticated user to
potentially enable denial of service via local access.
CVE-2025-24305: Insufficient control flow management in the Alias
Checking Trusted Module (ACTM) firmware for some Intel Xeon
processors may allow a privileged user to potentially enable
escalation of privilege via local access.
- Mitigations for INTEL-SA-01367 (Intel SGX, TDX):
CVE-2025-26403: Out-of-bounds write in the memory subsystem for some
Intel Xeon 6 processors when using Intel SGX or Intel TDX may allow
a privileged user to potentially enable escalation of privilege via
local access.
CVE-2025-32086: Improperly implemented security check for standard
in the DDRIO configuration for some Intel Xeon 6 Processors when
using Intel SGX or Intel TDX may allow a privileged user to
potentially enable escalation of privilege via local access.
- Fixes for unspecified functional issues on several Intel Core and
Intel Xeon processor models.
* Updated microcodes:
sig 0x000606a6, pf_mask 0x87, 2025-03-11, rev 0xd000410, size 309248
sig 0x000606c1, pf_mask 0x10, 2025-03-06, rev 0x10002e0, size 301056
sig 0x000806f8, pf_mask 0x87, 2025-04-04, rev 0x2b000643, size 592896
sig 0x000806f7, pf_mask 0x87, 2025-04-04, rev 0x2b000643
sig 0x000806f6, pf_mask 0x87, 2025-04-04, rev 0x2b000643
sig 0x000806f5, pf_mask 0x87, 2025-04-04, rev 0x2b000643
sig 0x000806f4, pf_mask 0x87, 2025-04-04, rev 0x2b000643
sig 0x000806f8, pf_mask 0x10, 2025-04-08, rev 0x2c000401, size 625664
sig 0x000806f6, pf_mask 0x10, 2025-04-08, rev 0x2c000401
sig 0x000806f5, pf_mask 0x10, 2025-04-08, rev 0x2c000401
sig 0x000806f4, pf_mask 0x10, 2025-04-08, rev 0x2c000401
sig 0x000a06a4, pf_mask 0xe6, 2025-03-19, rev 0x0025, size 140288
sig 0x000a06d1, pf_mask 0x95, 2025-05-15, rev 0x10003d0, size 1667072
sig 0x000a06d1, pf_mask 0x20, 2025-05-15, rev 0xa000100, size 1638400
sig 0x000a06f3, pf_mask 0x01, 2025-05-03, rev 0x3000362, size 1530880
sig 0x000b06a2, pf_mask 0xe0, 2025-02-24, rev 0x4129, size 224256
sig 0x000b06a3, pf_mask 0xe0, 2025-02-24, rev 0x4129
sig 0x000b06a8, pf_mask 0xe0, 2025-02-24, rev 0x4129
sig 0x000b06d1, pf_mask 0x80, 2025-05-21, rev 0x0123, size 80896
sig 0x000c0662, pf_mask 0x82, 2025-05-14, rev 0x0119, size 90112
sig 0x000c06a2, pf_mask 0x82, 2025-05-14, rev 0x0119
sig 0x000c0652, pf_mask 0x82, 2025-05-14, rev 0x0119
sig 0x000c0664, pf_mask 0x82, 2025-05-14, rev 0x0119
sig 0x000c06f2, pf_mask 0x87, 2025-04-15, rev 0x210002b3, size 564224
sig 0x000c06f1, pf_mask 0x87, 2025-04-15, rev 0x210002b3
Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc (Intel N150 PC)
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/20045
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds kernel packages for the Vitesse VSC73XX switches.
I have split the switch into explicit SPI and platform integrated
variants as it's quite a bit of code.
Link: https://github.com/openwrt/openwrt/pull/20057
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2ae08749a87e ucode: add padding to uc_resource_ext_t
7931bd901222 socket: add socket.pair()
4cd07cd66ab3 socket: add socket.open()
6350e6383ff3 struct: implement X and Z formats for hex and base64 coding
e632e6da1fbc vm: fix potential eyond end of array accesses
a7ead3169ebf resolv: properly handle multiple TXT strings
9d782ea4af63 math: Add an optional range to rand()
Fixes: https://github.com/jow-/ucode/issues/315
Fixes: https://github.com/jow-/ucode/issues/321
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Converts the KS8995 "phy" driver to a proper DSA switch.
Currently the upstream only supports the "none" tag
but this is a good improvement already.
Make the old module depend on kernel 6.6 and the new
one depend on !6.6.
The Realtek RTL8261n patch needs to be refreshed
because of textual dependencies.
Realtek RTL838x DSA and phy patches also have textual
dependencies and need to be refreshed.
The Mediatek in-flight DSA patch and related patches
also need to be rebased and refreshed.
Link: https://github.com/openwrt/openwrt/pull/19970
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2859741d971e dhcpv4: store reqopts as uint8_t
6d342cc03bf7 odhcpd: add DNR (RFC 9463) support
c89b8b3f2ff3 odhcpd: make the IPv6 RA DNR lifetime configurable
066b3dc6ec1a netlink: fix a memory leak
171140e90b6a odhcpd: add a helper function for addr6/prefix parsing
5585b969c18f router: move pref64 calculations to the config stage
4308384748be dhcpv6: add ipv6 pxe support
6e1ad492cef5 router: replace ssize_t with size_t
Signed-off-by: David Härdeman <david@hardeman.nu>
Link: https://github.com/openwrt/openwrt/pull/20022
Signed-off-by: Robert Marko <robimarko@gmail.com>
Version 6.15 - 29-Aug-2025
* netlink: fix missing headers in text output
* netlink: fix print_string when the value is NULL
Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/20021
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add support for the Lunzn FastRhino R66S board.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19990
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
PKG_MAKE_FLAGS is required when compiling r8168-rss
Signed-off-by: Andy Chiang <AndyChiang_git@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20001
Signed-off-by: Robert Marko <robimarko@gmail.com>
While these boards have an at24 EEPROM for storing the MAC address,
early revisions (up until about 2017) did not contain actual addresses.
Create a random address to have ethernet function properly in u-boot.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The version of libxml2 was bumped from 2.13.6 to 2.14.5. Since version
2.14, libxml2 is not binary compatible with older versions. Therefore
add an abi version.
From the NEWS file:
Binary compatibility is restricted to versions 2.14 or newer. On ELF
systems, the soname was bumped from libxml2.so.2 to libxml2.so.16.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Link: https://github.com/openwrt/openwrt/pull/19983
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
gettext-full only provides libintl which is not licensed under
GPL-3.0.-or-later but under LGPL-2.1-or-later as stated in
gettext-runtime/intl/COPYING.LIB
Fixes: c10d97484a (Add more license tags with SPDX identifiers)
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19943
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
