This commit fixes stability issues on certain RAX3000Me devices. Some
devices has DDR3 RAM which don't able to work reliably at 2133 MHz
and require special BL2 (1866 MHz RAM freq).
Fixes: https://github.com/openwrt/openwrt/issues/20046
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20059
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch has already been accepted and landed in 6.17.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20132
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
No functional changes intended.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20131
Signed-off-by: Robert Marko <robimarko@gmail.com>
No functional changes intended.
Fixes warning:
/linux/arch/arm64/boot/dts/airoha/en7581-gemtek-w1700k.dtb: i2c1@1fbf8100 (mediatek,mt7621-i2c): status: 'oneOf' conditional failed, one must be fixed:
['disable'] is not of type 'object'
'disable' is not one of ['okay', 'disabled', 'reserved', 'fail', 'fail-needs-probe']
from schema $id: http://devicetree.org/schemas/dt-core.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20131
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that there is a dedicated PCS driver remove the old functions
from the DSA driver and make use of the new ones.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20129
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
For all switch ports where the assigned SerDes is known, add the new
pcs-handle to the dts. Leave the existing <sds> assignments to the
PHYs as is because the driver has not yet been updated.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20111
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for Buffalo WSR-6000AX8 and AX8P models.
Hardware
--------
SOC: MediaTek MT7986B
RAM: 512MB
FLASH: 128MB SPI-NAND (Winbond)
WIFI 2.4G: (Embedded in SOC) b/g/n/ax, MIMO 4x4
WIFI 5G: (Embedded in SOC) a/n/ac/ax, MIMO 4x4
ETHERNET: 2.5GbE MaxLinear GPY211C (eth1: WAN)
ETHERNET: MediaTek MT7531AE 3xGbE (eth0: LAN1, LAN2, LAN3)
UART: 3.3V 115200 8N1
Serial(UART) Pin Layout
-----------------------
+-------+-------+-------+-------+
J4 | RX | TX | GND |(3.3V) |
+-------+-------+-------+-------+
(Bottom Side)
MAC Address Table
-----------------
lan1-3: board_data 0x4(text)
eth1/WAN: board_data 0x4(text)
WIFI 2.4G: lan1 + 2
WIFI 5G: lan1 + 9
Installation
------------
1. Set up a TFTP server with the IP address "192.168.11.2".
2. Rename the OpenWrt initramfs image to "linux.ubi-recovery" and place it
in the TFTP server's root directory.
3. While holding down the AOSS button, power on the WSR-6000AX8 (or AX8P).
4. The device will automatically download the initramfs image
from the TFTP server and boot into it.
5. Once booted, run "sysupgrade -n" using the OpenWrt sysupgrade image
to complete the installation.
Recovery
--------
1. Decrypt the official firmware image using "buffalo-enc".
example:
$ buffalo-enc -d -i wsr_6000ax8_jp_100 -o wsr_6000ax8_jp_100.dec \
-l -O 0xc8
2. Run "sysupgrade -F -n" with the decrypted image.
Signed-off-by: Shin Sato <shin.sugar.ssyysy2021@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/13107
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification :
- SOC : Mediatek MT7981B (1.3GHz)
- RAM : 256MB
- Flash : 16MB SPI NOR
- Ports : 4 LAN (1G) & 1 WAN (1G)
- WIFI : MediaTek dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Buttons : Reset & WPS/Mesh
- LEDS : WAN (Green), Status (Red & Blue)
- Power : 12V1A
Install via OEM web ui:
Upload the sysupgrade image to firmware upgrade page on OEM web ui
Install via recovery / revert to stock firmware:
1. Unplug from power
2. Download the Sysupgrade (for openwrt installation) or OEM Factory image (for revert to stock firmware)
3. Set your computer ethernet IP to 192.168.1.X, subnet 255.255.255.0 (X=your chosen ip number ranging from 2-254)
4. Press and hold reset button while turn on / plug power adapter to the router. Wait untill ALL LAN green LED turn on, then release the reset button.
5. Plug the LAN cable from your computer into LAN 1 port then open web browser, and type in the address column : 192.168.1.1
6. Upload the sysupgrade / oem factory image
7. Wait until the router finished flashing (the router will reboot)
8. Set ethernet ip to dhcp
9. Open 192.168.1.1 (for openwrt install) / 192.168.0.1 (for OEM firmware)
Signed-off-by: Ari Kurniawan <noobhek@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20035
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that we have a board file, add calibration variant for TP-Link
Archer C60 v1 and add ipq-wifi package for it.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19993
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes a previous commit breaking setting the MAC address for the
wifi devices.
Fixes: 9ed4d27fbf ("mediatek: filogic: fix 5G MAC address for Zyxel EX5601")
Link: https://github.com/openwrt/openwrt/pull/20100
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Until now the the SerDes configuration is realized with helper functions
scattered around the DSA and PHY driver. Give them a new home as a PCS
driver.
The target design is as follows:
- dsa driver manages switch
- pcs driver manages SerDes on high level (this commit)
- mdio driver manages SerDes on low level
This driver adds the high level SerDes access via PCS. It makes use of
the low level mdio SerDes driver to access the registers.
Remark: This initial version provides exactly all phylink_pcs_ops that
are currently part of the DSA driver. So this can be swapped in one of
the next commits as a drop in replacement. To make use of it something
like this is needed:
...
ports = of_get_child_by_name(node, "ethernet-ports");
if (!ports)
return -EINVAL;
for_each_available_child_of_node(ports, port) {
pcs_node = of_parse_phandle(port, "pcs-handle", 0);
of_property_read_u32(port, "reg", &port_nr)) {
priv->pcs[port_nr] = rtpcs_create(dev, pcs_node, port_nr);
}
...
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20075
Signed-off-by: Robert Marko <robimarko@gmail.com>
In the future the PCS & DSA drivers will lookup the SerDes of a
switch port via pcs-handle (like upstream does). Provide a macro
that allows to expand the existing port definitions. To link a
SerDes to port simply do
Either in short form:
replace SWITCH_PORT(0, 1, qsgmii)
with SWITCH_PORT_SDS(0, 1, 3, qsgmii) (Link to SerDes 3)
Or in long form:
port@24 {
reg = <24>;
label = "lan25";
pcs-handle = <&serdes4>; (Link to SerDes 4)
phy-handle = <&phy24>;
phy-mode = "1000base-x";
managed = "in-band-status";
sfp = <&sfp0>;
};
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20075
Signed-off-by: Robert Marko <robimarko@gmail.com>
The fixes for the dying timers were finally accepted upstream.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20097
Signed-off-by: Robert Marko <robimarko@gmail.com>
Instead of having two LED entries that supposedly control the same
thing, set the pin properly.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18905
Signed-off-by: Robert Marko <robimarko@gmail.com>
of_gpio.h is deprecated in upstream Linux and may be removed soon. Get
ahead of things and remove it. Most of these drivers already use the
gpiod API.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20076
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is a smart door lock device equipped with OpenWrt 14.07 OEM
modified version Qdwrt
The OEM has closed down, This commit is intended to maximize the
remaining value of these devices. It can flash OpenWrt to become
an AP
Specification:
- SoC: MediaTek MT7628NN
- Flash: 8 MB
- RAM: 64 MB
- Power: DC 5V - 25V
- Ethernet: 1 x RJ45 (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only
- On-Board LED:
Status 1: GPIO/43 active-low
Status 2: GPIO/44 active-low
Power: AlwaysOn
- Button:
WPS / RESET: GPIO/14 active-low
- Bluetooth: CC2541 via UART1 (ttyS1) and GPIO/26-29
- RFID: MF RC522 on I2C@28
- RTC: DS1339 on I2C@68
- Shell (via CON1 cable)
- LED (Swipe card area):
- Green GPIO/3 active-high
- Red GPIO/11 active-high
- Matrix keypad: (active-low)
GPIO/20 GPIO/21 GPIO/19 (Rows)
GPIO/24 1 2 3
GPIO/25 4 5 6
GPIO/22 7 8 9
GPIO/23 BACK 0 ENTER
(Cols)
- UART: 1 x UART on PCB - 57600 8N1
- GPIO Relay: GPIO/42 active-high
- GPIO Buzzer: GPIO/15 active-high
Warning:
The original firmware does not use the device tree.
This device tree is written based on the content of /sys/devices/platform
and has been tested
Note:
- On the device, matrix keypad rows actually are columns, and the columns actually are rows
- The key code of the CLEAR key of the matrix keypad is BACK in the original firmware.
Issue:
- No drivers in mainline kernel for RFID and Bluetooth.
Flash Instruction:
Using SSH/Telnet:
1. Connect the board to the computer via RJ45 Ethernet
2. Login 10.10.10.1 with root password "szqdingnet123" (SSH Port 22, Telnet Port 9900)
3. Download openwrt firmware on the computer.
4. Setup a http server on computer. And use wget download openwrt firmware from computer
5. Use command "mtd -r write openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin firmware"
to flash
Using U-Boot WebUI:
1. Configure PC with a static IP address 10.10.10.2/24.
2. Open http://10.10.10.1
3. Use "mkqdimg -B qc202 -f openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin" to
make image.
4. Upload factory.bin via U-Boot WebUI.
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-qianding-smart-locker-and-flash.html
Original U-Boot firmware image tools:
https://gitlab.com/CoiaPrant/mkqdimg
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17471
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently following warnings are given
dts/rtl930x.dtsi:166.4-23: Warning (reg_format):
/switchcore@1b000000/i2c@36c:reg: property has invalid length
(8 bytes) (#address-cells == 2, #size-cells == 1)
Obviously default address-cells size is fixed to 64 bit. Align
with upstream and override address size to 32 bit.
Suggested-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20091
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add node to support the second UART node controller in IPQ5018.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20090
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specification:
SoC: Mediatek MT7981BA
RAM: 512 MB DDR4 RAM
Flash: Winbond W25N01GV 128 MB SPI-NAND (dual boot on OEM)
WiFi: MT7976CN DBDC AX
Switch: MediaTek MT7531AE (3x LAN Gigabit ports) + Internal Gbe Phy (1x WAN Gigabit port)
GPIO: 4x LED (power, internet, fn, wifi), 2x buttons (wps, reset), 1x switch (mesh)
UART Interface:
Pins: VCC, TX, RX, NC, GND
Settings: 115200, 8N1
Flashing via TFTP:
1. Connect your PC and router to the first LAN port, configure PC interface using IP 192.168.1.2, mask 255.255.255.0
2. Save the factory image of the OpenWRT firmware, renamed to KN-3711_recovery.bin, on the TFTP server
3. Hold the reset button and power up the device
4. Keep the button pressed until the status LED starts blinking
Signed-off-by: Vladimir Epifantsev <volatilefield@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19633
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The EN751221 has an XHCI that is compatible with MT7621.
While there is setup logic in the vendor code for both
EN751221 and MT7621, but MT7621 does not use it in mainline
or OpenWRT, and it appears to work correctly with EN751221.
Include SCSI / Mass Storage because many EcoNet devices
contain a builtin USB SD-Card reader.
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://github.com/openwrt/openwrt/pull/20050
[Remove usb storage kmod from smartfiber_xp8421-b]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The baud rate control on Airoha does not function properly. This
patch enables the inactive code responsible for this. The UART2
baud rate is correct. HSUART3 operates at twice the requested
baud rate. The same problem exists in the current code, so this
doesn't introduce any regression. Support for baud rates higher
than 460800 is still required. This will be added in the future.
Tested on Gemtek W1700k. UART2 and HSUART3 are working fine.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20049
Signed-off-by: Robert Marko <robimarko@gmail.com>
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.12.47
No patches needed to be rebased.
Build system: x86/64
Build-tested: Build-tested: flogic/xiaomi_redmi-router-ax6000-ubootmod, x86/64-glibc
Run-tested: flogic/xiaomi_redmi-router-ax6000-ubootmod, x86/64-glibc
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/20003
Signed-off-by: Robert Marko <robimarko@gmail.com>
The driver makes its own ath9k LED which handles everything.
Simplifies DTS slightly.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20023
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling for this is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20023
Signed-off-by: Robert Marko <robimarko@gmail.com>
The upcoming PCS driver will lookup the SerDes mdio bus via
of_mdio_find_bus() and the devicetree. This is only possible
with proper registration via devm_of_mdiobus_register().
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20078
Signed-off-by: Robert Marko <robimarko@gmail.com>
No need two write a dedicated 1:1 mapping function and link that
for all the targets except RTL931x. Combine everything into a generic
helper and reduce the configuration structure.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20078
Signed-off-by: Robert Marko <robimarko@gmail.com>
The new SerDes mdio driver produces the following compilation
error in non-debug builds.
drivers/net/mdio/mdio-realtek-otto-serdes.c:72:12:
error: 'rtsds_sds_to_mmd' defined but not used [-Werror=unused-function]
72 | static int rtsds_sds_to_mmd(int sds_page, int sds_regnum)
| ^~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Move the function into the debug section.
Fixes: 7a7ee72c4d ("realtek: mdio: add SerDes driver")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20078
Signed-off-by: Robert Marko <robimarko@gmail.com>
In first commit I successfully bring WAN port into ethernet switch,
without realizing that I was using custom bootloader. But if using
original bootloader it do not works. WAN port in original bootloader
is tied to using its own GMAC.
This fix is made so this firmware will be compatible with orignal
bootloader, so the user can directly flash from stock firmware without
changing anything.
Signed-off-by: Roy H <roy@altbytes.com>
Link: https://github.com/openwrt/openwrt/pull/20039
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Despite having the same tplink.dtsi file, there are differences in wifi
Move wifi nodes out of dtsi to make it clear what the chipset is and
what calibration size should be used.
While at it, change to use led-sources to simplify LED setup.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20024
Signed-off-by: Robert Marko <robimarko@gmail.com>
Until now the SerDes access is realized with some helper functions
in the mdio bus. These were moved around a lot and had no real home.
End that temporary solution to move them where they belong.
The target design for the different Realtek drivers is as follows:
- dsa driver manages switch
- pcs driver manages SerDes on high level (to be developed)
- mdio driver manages SerDes on low level (this commit)
This driver adds the low level SerDes access via mdio. For debugging
purposes the user can interact with the SerDes in different ways.
First, there is a debug interface in
/sys/kernel/debug/realtek_otto_serdes/serdes.X/registers.
With that a dump of all registers can be shown.
> cat /sys/kernel/debug/realtek_otto_serdes/serdes.4/registers
Back SDS 4: 00 01 02 03 04 05 06 07 08
SDS : 0C03 0F00 7060 7106 074D 0EBF 0F0F 0359 5248
SDS_EXT : 0000 0000 85FA 8C6D 5CCC 0000 20D8 0003 79AA
...
Second, one can read/write registers via the mmd functions of the
mdio command line tool. Important to know: The registers are accessed
on the vendor specific MDIO_MMD_VEND1 device address (=30). Additionally
the SerDes page and register are concatenated into the the mmd register.
Top 8 bits are SerDes page and bottom 8 bits are SerDEs register.
E.g.
- mmd 0x0206 : SerDes page 0x02, SerDes register 0x06
- mmd 0x041f : SerDes page 0x04, SerDes register 0x1f
Read register 0x02 on page 0x03 of SerDes 0
> mdio realtek-serdes-mdio mmd 0:30 raw 0x0302
Write register 0x12 on page 0x02 of SerDes 1
> mdio realtek-serdes-mdio mmd 1:30 raw 0x0212 0x2222
For now this driver is only defined in the devicetree and activated
in the kernel build. There is no current consumer but at least
the debugging interface is available. Cleanup of the currently used
SerDes functions will come later.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20062
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is some open coding in the ethernet driver. Drop
that and use kernel helpers instead.
- Use napi_gro_receive() instead of local skb list
- Use skb_put_data() instead of skb_put() plus memcpy()
- Use netdev_alloc_skb_ip_align() instead of manual alignment
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/20030
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh patches 6.12 for airoha and econet
Fixes: 122135b964 ("airoha: an7581: add support for kernel 6.12")
Fixes: 73d0f92460 ("kernel: Add new platform EcoNet MIPS")
Signed-off-by: Leo Barsky <leobrsky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/20073
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use upstreamed patch for adding the QUP3 I2C node.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20070
Signed-off-by: Robert Marko <robimarko@gmail.com>
Enable kernel 6.12 as the testing kernel for airoha.
This first commit will largely maintain feature-parity with kernel 6.6.
DTS changes are backwards-compatible with kernel 6.6.
Tested to flash and boot on Gemtek W1700K (#17869).
Signed-off-by: Kenneth Kasilag <kenneth@kasilag.me>
Link: https://github.com/openwrt/openwrt/pull/19038
Signed-off-by: Robert Marko <robimarko@gmail.com>
