Add ubi nvmem driver, required to load nvmem entries from ubi volumes
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Link: https://github.com/openwrt/openwrt/pull/22151
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Enable fitblk driver, required to parse the fit image and set-up the rootfs volume
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Link: https://github.com/openwrt/openwrt/pull/22151
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Due to issues surrounding the implementation of the vendor BMT/BBT
on Airoha, upstream ATF + uboot has switched to UBI flash partitions.
However, some devices shipped on this platform are bootloader locked,
and thus it is impossible to replace ATF + uboot.
During testing for the Gemtek W1700K (#17869), sysupgrades from Linux
(which is unaware of the underlying BMT/BBT) would occasionally write
data into blocks which were remapped by the vendor uboot when it was
read on the following reboot, causing a soft brick.
An acceptable workaround [1],[2] was discussed where an intermediate
uboot would be written by the vendor uboot (which is aware of Airoha
BMT/BBT). This chainloader would then ignore the regions of flash
used by the vendor uboot, and store all relevant data inside of UBI.
UBI would then be used to handle bad block management. As the vendor
ATF + uboot do not read or interact with the UBI region, we would avoid
unwanted remaps from BMT/BBT.
This commit introduces support for building such a chainloader, by
packaging u-boot and DTS into a FIT image; to be flashed like a kernel.
Configuration for the Gemtek W1700K is provided as an example of how the
chainloader is used.
[1] https://github.com/openwrt/openwrt/pull/17869#discussion_r2836066746
[2] https://github.com/openwrt/openwrt/pull/17869#discussion_r2838395671
Signed-off-by: Kenneth Kasilag <kenneth@kasilag.me>
[ move FIP_COMPRESS to Build/Compile, wrap some long lines ]
Link: https://github.com/openwrt/openwrt/pull/22151
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Due to confusing Documentation, the SPI and SLIC base clock and
register location for Airoha AN7583 SoC were wrong.
Fix them with new updated Documentation source to provide correct
clock support.
Fixes: c5b12fc02a ("airoha: Introduce support for Airoha AN7583 SoC")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix two hardware initialization issues in the EN7581 PCIe controller
and add support for x2 (2-lane) link mode.
Fixes:
The upstream EN7581 PCIe initialization writes EQ presets and PIPE
configuration registers before clk_bulk_prepare_enable(). Since the
MAC clocks are not yet running at that point, these register writes
are silently dropped, leaving the hardware with default values. This
can cause link training failures or suboptimal equalization.
Additionally, after link training the MAC may only advertise Gen1-Gen2
capability in the Link Capabilities 2 register despite the PHY being
configured for Gen3. A serdes reset toggle forces the MAC to re-read
PHY capability, recovering Gen3 8GT/s link speed.
Both issues are addressed by separating PERST from the clock callbacks
(patch 911), allowing the PCIe controller driver to properly sequence
PERST, clock enable, and register writes (patch 912).
New feature:
PCIe x2 mode support for EN7581 using the NP_SCU system controller
for serdes mux routing, PERST management, and lane configuration.
Both bonded MACs are configured for x2 operation with proper EQ
presets before link training begins.
Signed-off-by: Ryan Chen <rchen14b@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21978
Signed-off-by: Robert Marko <robimarko@gmail.com>
The MT7531 has an incorrect interrupt number described in the DTS.
This commit also adds PHY interrupts. They work the same as on
the MT7988.
Tested on Gemtek W1700k.
Suggested-by: Benjamin Larsson <benjamin.larsson@genexis.eu>
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/21016
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport a patch that reduces the quality of HWRNG. HWRNG has lower
entropy than expected. Thanks to this patch, it has a lower priority.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/21722
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport a bunch of upstream commits simplifying the RealTek PHY driver
and re-unifying the C22 and C45 driver instances.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Implement the .get_link_ksettings to get the rate, duplex, and
auto-negotiation status.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/21530
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit ab805ec316 ("generic: add missing squashfs config") enabled
CONFIG_SQUASHFS_DECOMP_MULTI_PERCPU in the generic config, so it is no
longer needed in the target configs.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Link: https://github.com/openwrt/openwrt/pull/21465
Signed-off-by: Robert Marko <robimarko@gmail.com>
Let node unit address same as reg.
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20482
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Different boards use different port map. For example, some board may use
a GE port as WAN. So defining the led label in board-level is better.
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20482
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Different boards use different port map. Defining the port labels in
board-level is better.
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20482
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some board only use some of them, so enable as necessary in
board-level dts.
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20482
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes a bug in a patch we backported.
This patch was cherry picked from upstream Linux because it references a
patch we backported in the fixes tag.
The first two patches are providing function needed by the last patch.
Fixes: 813ecda1f3 ("generic: backport phylink patches for PCS/PHY caps OPs")
Link: https://github.com/openwrt/openwrt/pull/21366
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes a bug in a patch we backported.
This patch was cherry picked from upstream Linux because it references a
patch we backported in the fixes tag.
The function phy_id_compare_vendor() is needed by the fix.
Refresh 782-05-v6.16-net-phy-Add-support-for-Aeonsemi-AS21xxx-PHYs.patch with the upstream code.
Fixes: 08a616b216 ("generic: backport support for Aeonsemi AS21xxx PHY")
Link: https://github.com/openwrt/openwrt/pull/21366
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix the unit-address of the scuclk node.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20985
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
No functional changes intended.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20985
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Replace patches with version accepted upstream.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/21333
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Changes:
* use upstream patches for airoha-snfi driver
* update in kernel en7523 dts to add spinand support
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/21299
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move reserved_mem backports patch from airoha to generic dir as it will
be also used by backports package based on 6.18.
Link: https://github.com/openwrt/openwrt/pull/20964
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Commit 8f1914053b ("airoha: replace I2S patch with upstream pending
version") introduced a kernel panic with I2S driver.
Add the fixed patch to fix the kernel panic.
Fixes: 8f1914053b ("airoha: replace I2S patch with upstream pending version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Enable I2S sound driver and add nodes for eMMC RFB board since it's the
one that always have the I2C codec and can use the sound card.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace I2S sound patch with upstream pending version. This adds ETDM
support and fix various bug in the downstream implementation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport upstream patch to add support for the ESMT F50L1G41LC flash
chip. It is used in multiple Cudy products manufactured starting
November 2025.
Link: https://github.com/openwrt/openwrt/pull/20962
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use latest patch version
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20400
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
There is no reason not to do this.
Use the following commands to enable hardware offloading:
uci set firewall.@defaults[0].flow_offloading='1'
uci set firewall.@defaults[0].flow_offloading_hw='1'
uci commit
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20484
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport changes to the pinctrl driver to bring it closer to
the upstream version. Also fix the bug in the pinctrl driver:
pinctrl-airoha ...pinctrl: invalid function mdio in map table
Fixes: bd7f5b3 ("airoha: replace AN7583 pinctrl patch with upstream version")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20770
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The I2C and UART patch numbers are duplicates
of other patches, so reordered them.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20770
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport the kernel parf of the WiFi MT76 offload patch. This is needed
as we have a dedicated package that only have mt76 related changes.
Add missing include in airoha_offload.h in order to enable MT76 NPU
offloading (and fix compilation error)
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
[ improve commit title/description and use proper patch ]
Link: https://github.com/openwrt/openwrt/pull/20807
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace Airoha AN7583 pinctrl patch with upstream version as it has been
accepted upstream. Add the related kernel version tag to identify it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport upstream patch fixing out of order DMA access for ethernet
driver. This is relevant in the context of QoS when packets doesn't
follow linear handling by QDMA HW.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
KConfig flag have an extra whitespace for CONFIG_PHY_AIROHA_USB and
value is not ignored.
Drop the extra whitespace to correctly ignore the value on kernel
compilation.
Fixes: c5b12fc02a ("airoha: Introduce support for Airoha AN7583 SoC")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add support to the airoha target for the OpenWrt-specific DT property
`openwrt,netdev-name`. In particular, this is for interfaces under
non-DSA `airoha_eth` interfaces.
This will avoid conflicts with upstream code[1]; and maintain forward
compatibility with OpenWrt configurations if/when `airoha_eth` becomes
a full DSA driver.
[1] https://lore.kernel.org/netdev/20240709124503.pubki5nwjfbedhhy@skbuf/
Borrowed from d4d6c48 (mediatek: filogic: support openwrt,netdev-name for renaming interfaces)
Signed-off-by: Kenneth Kasilag <kenneth@kasilag.me>
Link: https://github.com/openwrt/openwrt/pull/20475
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport upstream minor fixed for NPU handling that might result in
kernel panic or handle leak.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add missing leds and network board files for EN7581 SoC.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
[ drop reference to downstream 10g RFB board ]
Link: https://github.com/openwrt/openwrt/pull/20556
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
