This simplifies script or API usage of this command to remove values directly
without having to calculate the index
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: M16U4G16256A DDR4 512MB
Ethernet: 2x 2.5G + 3x 1G
USB: 1x USB 3.0
WiFi1: MT7975N 2.4GHz 4T4R
WiFi2: MT7975PN 5GHz 4T4R
Button: Reset, WPS
Power: DC 12V 2A
Flash instructions:
Connect to the router using ssh or telnet,
username: useradmin, password is the web
login password of the router.
Use scp to upload bl31-uboot.fip and flash:
"mtd write xxx-bl31-uboot.fip FIP"
"mtd erase ubi"
Connect to the router via the Lan port,
set a static ip of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
Download initramfs image, reboot router,
waiting for tftp recovery to complete.
After openwrt boots up, perform sysupgrade.
Note:
Back up all mtd partitions before flashing.
Signed-off-by: Yujie Zhu <libriunc@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18138
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add qualcommbe to the supported target of dwc3-qcom kernel module. USB3
is correctly supported on IPQ95xx and can be enabled.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently if a target wants to use acm or ncm gadget config,
they need to select both usbgadget and the config package
such as usbgadget-acm.
It's better if the target just select usbgadget-acm and get
all dependencies satisfied.
Adding a dependency using +usbgadget fixes this.
Link: http://patchwork.ozlabs.org/project/openwrt/patch/20250403-dns313-usb-serial-v2-3-d84de8e86931@linaro.org/
Reviewed-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ath9k uses a deprecated GPIO API that assumes a starting base of 0. This
is no longer the case and so must be fixed.
Upstream pending patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is only used by mach files, which are no longer used in OpenWrt.
Allows removing a custon ath9k_platform.h file.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
These only work with and are useful with mach files. Now that those are
gone, this can go too.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
Simplify patch with gpiochip_add_data, struct reduction, new GPIO API,
and header cleanup.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
* SoC: Qualcomm IPQ6018 (64-bit Quad-core Arm Cortex-A53 @ 1800MHz)
* Memory: 1 GiB
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN9074 (4x4 5 GHz 802.11ax)
* Wi-Fi: IPQ6018 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: RTL8211F (10/100/1GBASE-T)
* Flash: ESMT F59D1G81MB (128 MiB)
* LEDs: 1x Green Status (GPIO 37 Active High), 1x Yellow Status (GPIO 32
Active High) and an LED global control GPIO (GPIO 36 Active High, set
up by U-Boot)
* Buttons: 1x Reset (GPIO 9 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to the pads near T32 and T31.
2. Connect 3V3 TTL port to TX, RX, and GND, which are pad T31, T32 and
the pad near T31 respectively. Be sure not to connect VCC and
crossover TX and RX.
3. Copy RAM firmware image
openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb
to TFTP server root, available at 192.168.0.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# setenv serverip 192.168.0.1
# setenv ipaddr 192.168.0.99
# tftpboot 0x44000000 openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18389
Signed-off-by: Robert Marko <robimarko@gmail.com>
In recent glibc versions rpc functionality has been moved to a separate
library instead of glibc itself.
Depend on this library when rpc functionality is needed and glibc is
used.
Signed-off-by: Matthias Franck <matthias.franck@softathome.com>
Link: https://github.com/openwrt/openwrt/pull/17796
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
For WIFI7 devices (such as mt7925e), the dev width is currently
always "20 MHz (no HT)" in monitor mode.
Add EHT and HE160 support to iw_htmode to fix this issue.
Additionally, the following changes are made:
1. Set iw_htmode to 160MHz for VHT160. The reason for the current
VHT160 setting is unclear and seems to have been in place for
over a decade (ibss_htmode [1]). If anyone knows its impact,
please inform me so I can restore it.
2. Modify MHZ to MHz. The original matching table in the current
iw tool uses MHz. Although the match is case-insensitive,
correcting this won't hurt.
[1]: 768d09be87
Signed-off-by: Ming Kuang <ming@imkuang.com>
Link: https://github.com/openwrt/openwrt/pull/18319
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Enable building U-Boot/qca9558_nec_aterm profile for NEC Aterm WG2200HP.
This model has almost the same hardware as the other Aterm devices based
on Qualcomm Atheros QCA9558.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17584
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This PR adds support for netis NX31 router.
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM : 256 MiB DDR3
- Flash : SPI-NAND 128 MiB (ESMT)
- WLAN : MediaTek MT7976CN dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x3 (LAN, MediaTek MT7531AE)
10/100/1000 Mbps x1 (WAN, SoC internal phy)
- USB : No
- Buttons : Mesh, Reset
- LEDs : 1x Power (blue), unmanaged
1x Status (blue), gpio-controlled
1x WiFi 2.4 GHz (blue), gpio-controlled
1x WiFi 5 GHz (blue), gpio-controlled
3x LAN activity (blue), switch-controlled
1x WAN activity (blue), gpio-controlled
- Power : 12 VDC, 1 A
Installation
------------
1. Connect to the router using ssh (user: admin, pass: web interface
password)
2. Make mtd backup:
cat /dev/mtd0 | gzip -1 -c > /tmp/mtd0_spi0.0.bin.gz
cat /dev/mtd1 | gzip -1 -c > /tmp/mtd1_BL2.bin.gz
cat /dev/mtd2 | gzip -1 -c > /tmp/mtd2_u-boot-env.bin.gz
cat /dev/mtd3 | gzip -1 -c > /tmp/mtd3_Factory.bin.gz
cat /dev/mtd4 | gzip -1 -c > /tmp/mtd4_FIP.bin.gz
cat /dev/mtd5 | gzip -1 -c > /tmp/mtd5_ubi.bin.gz
3. Download mtd backup from the /tmp dir of the router to your PC using
scp protocol
4. Upload OpenWrt 'bl31-uboot.fip', 'preloader.bin' images to the /tmp
dir of the router using scp protocol
5. Write FIP and BL2 (replace bootloader):
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-bl31-uboot.fip FIP
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-preloader.bin BL2
6. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
7. Erase 'ubi' partition and reboot the router:
mtd erase ubi
reboot
8. U-Boot automatically boot OpenWrt recovery image from tftp server to
the RAM
9. Upload OpenWrt 'sysupgrade.itb' image to the /tmp dir of the router
(IP: 192.168.1.1) using scp protocol
10. Connect to the router using ssh and run:
sysupgrade -n openwrt-mediatek-filogic-netis_nx31-squashfs-sysupgrade.itb
Return to stock
---------------
1. Unpack stock BL2 and FIP partitions backup
2. Upload stock BL2 and FIP partitions backup to the /tmp dir of the
router using scp protocol
3. Connect to the router using ssh and run:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd unlock FIP
4. Restore backup:
mtd write /tmp/mtd4_FIP.bin FIP
mtd write /tmp/mtd1_BL2.bin BL2
5. Erase ubi and reboot:
mtd erase ubi
reboot
6. Power off the router
7. Press Reset button and power on the router. Release the button after
~10 sec
8. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware
Recovery
--------
1. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
2. Press “Reset” button and power on the router. After ~10 sec release
the button.
3. Use OpenWrt initramfs system for recovery
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | dc:xx:xx:d1:xx:18 | label |
| WAN | dc:xx:xx:d1:xx:1a | label+2 |
| WLAN 2g | de:xx:xx:11:xx:19 | |
| WLAN 5g | de:xx:xx:71:xx:19 | |
+---------+-------------------+-----------+
The LAN MAC was found in 'Factory', 0x1fef20
The WAN MAC was found in 'Factory', 0x1fef26
The WLAN 2g/5g MAC prototype was found in 'Factory', 0x4
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18324
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
**Huasifei WH3000 eMMC / Fudy MT3000**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC.
MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ
**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8GB
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: power/reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1
**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.
**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.
**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-emmc-squashfs-sysupgrade.bin
```
**Factory MAC**
You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4`
```
dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C
```
**Enlarging a partition**
Though device has 8GB eMMC, it uses only 2GB `/dev/mmcblck0p6` as `rootfs` for `/rom` and `/overlay` leaving `/dev/mmcblck0p7` as empty unused space.
```
sgdisk -p /dev/mmcblk0
```
```
Disk /dev/mmcblk0: 15269888 sectors, 7.3 GiB
Sector size (logical/physical): 512/512 bytes
Disk identifier (GUID): 2BD17853-102B-4500-AA1A-8A21D4D7984D
Partition table holds up to 128 entries
Main partition table begins at sector 2 and ends at sector 33
First usable sector is 34, last usable sector is 14942174
Partitions will be aligned on 1024-sector boundaries
Total free space is 11197 sectors (5.5 MiB)
Number Start (sector) End (sector) Size Code Name
1 8192 9215 512.0 KiB 8300 u-boot-env
2 9216 13311 2.0 MiB 8300 factory
3 13312 21503 4.0 MiB 8300 fip
4 21504 29695 4.0 MiB 8300 config
5 29696 62463 16.0 MiB 8300 kernel
6 62464 4256767 2.0 GiB 8300 rootfs
7 4257792 14940159 5.1 GiB 8300
```
You can fix that by loading into `initramfs-kernel`, deleting empty `mmcblck0p7` partition and resizing `mmcblck0p6`
```
sysupgrade -F /tmp/openwrt-initramfs-kernel.bin
```
Install and run cfdisk
```
opkg update && opkg install cfdisk
cfdisk /dev/mmcblck0
```
- Select `mmcblck0p7` -> Delete
- Select `mmcblck0p6` -> Resize -> Write -> yes -> Quit
You will not see any difference in `cat /proc/partitions` after that but just flash a `sysupgrade` and you'll get the whole 7.3GB space for the `/overlay`.
Co-developed-by: hecatae <horus.ra@gmail.com>
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18220
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ATF supports rk3588 since version 2.12, so let's enable it in
arm-trusted-firmware-rockchip.
We still need the TPL to initialize RAM, but keeping rk3588 in rkbin
would cause a duplicate package name, so rename rk3588 to rk3588-tpl in
rkbin.
Finally, point uboot-rockchip for rk3588 to bl31 built by this package,
and add a dependency on the new trusted-firmware-a-rk3588-tpl pacakge.
While this doesn't necessarily add features, we now no longer rely on
the rk3588_bl31_v1.45.elf blob provided by Rockchip, which is always a
good thing.
Tested on Radxa ROCK 5B+.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
And remove no-warn-rwx-segments hack, as this is no longer needed and
actually causes build to fail. See also commit c117d7a37a
("include/trusted-firmware-a.mk: remove the no-warn-rwx-segments hack").
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Currently, building at91 subtargets via image builder will fail as the
required built at91bootstrap is not present in the image builder at all
since its presumed to be in the binary directory which obviously does not
exist yet.
So, lets install the at91bootstrap binary into image staging directory and
use that instead
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, building at91 subtargets via image builder will fail as the
required built u-boot is not present in the image builder at all since its
presumed to be in the binary directory which obviously does not exist yet.
So, lets install the u-boot binary into image staging directory and use
that instead.
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
Netgear WAX610 / WAX610Y is a 802.11ax AP claiming AX1800 support.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512MB
* Storage: Winbond W29N01HZBINF 128MB NAND
* Ethernet:
* 2.5GbE RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Power: Dual-color LED (Green / Orange), Single-color LED (Blue)
* Ethernet: Dual-color LED (Green / Orange)
* 2.4Ghz WiFi: 2x Single-color LED (Blue, Green)
* 5Ghz WiFi: 2x Single-color LED (Blue, Green)
* Buttons:
* 1x Reset
* UART: 4-pin populated header
* Pinout 1 - VCC, 2 - GND, 3 - TX, 4 - RX
Installation:
=============
Web UI method
-------------
Set up the device using the stock web UI in local management mode.
Download the ui-factory.tar image.
* Enter the Management tab
* Select Maintenance->Upgrade->Firmware Upgrade
* Ensure the "Upgrade Options" field has "Local" selected
* Click "Browse File" and select the image
* Click "Upgrade" (NOT "Upgrade Now") at the bottom of the page
The device will install the image but reboot back into the vendor
firmware. Return the to Firmware Upgrade page as above and select
"Boot up Backup Firmware". The device should reboot into OpenWRT.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot netgear_wax610-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the command line.
Signed-off-by: Erik Servili <serverror@serverror.com>
Link: https://github.com/openwrt/openwrt/pull/18377
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath10k dt-binding property "qcom,coexist-support" was
explicitly defined as type uint8 since upstream commit
ed09c61eb19d ("dt-bindings: net: Convert ath10k to YAML").
Therefore, this hack patch no longer makes sense.
Link: ed09c61eb1
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18393
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport two commits to resolve issues with ath1kk causing it to fail
driver registration on iommuless systems with DRAM outside of 32bit
addressing such as a 4GiB imx8mm:
commit 1bcd20981834 ("wifi: ath11k: Fix DMA buffer allocation
to resolve SWIOTLB issues")
commit eeadc6baf8b3 ("wifi: ath11k: Use dma_alloc_noncoherent
for rx_tid buffer allocation")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/17751
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit 1375a7bae0.
This version does not activate the CONFIG_LEDS_CLASS_MULTICOLOR option,
this option is controlled by the generic target configuration.
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/17277
[Reword commit message]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Although ath10k pre-calibration data and board description file
have similar data structures, they are completely different things.
Therefore, let's remove these incorrect and confusing links.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18069
Signed-off-by: Robert Marko <robimarko@gmail.com>
This new version fixes some memory leak and NULL pointer issues.
Upstreamed patches:
[1] 010-api_update.patch
[2] 201-wifi-ath10k-add-LED-and-GPIO-controlling-support-for.patch
The new 003 patch was introduced to fix the build error on old LTS
kernel. The patch 004 was used to fix the issue of IPQ4019 radio
not being able to start.
Tested on QCA9882 and IPQ4019.
[1] bca8bc0399
[2] 8e1debd824
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18368
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove settings and depends that are not used anywhere.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18291
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
b6e5157527d3 fw4: fix reading kernel version
42d3b3d4ca21 fw4: allow family any for ipsets not matching IP addresses
edfdfc6df484 Revert "fw4: allow family any for ipsets not matching IP addresses"
97962771aa3c config: drop to-be-forwarded-nowhere packets on wans
00fc6943a297 init: remove unnecessary stop logic
ad3cba79c192 fw4: allow family any for ipsets not matching IP addresses
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
[fix PKG_MIRROR_HASH]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18283
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix compilation error for old stable version caused by
genlmsg_multicast_allns backport fix pushed middle version.
Version 5.15 version 0-169, 6.1 version 0-115, 6.6 version 0-58 have the
old genlmsg_multicast_allns version with flags variable.
Compiling backport project with these version result in a compilation
error. To handle this, introduce a backport function for the affected
kernel version.
Link: https://github.com/openwrt/openwrt/pull/18373
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add U-Boot build for the ASUS ZenWiFi BT8 intended to replace the
stock loader.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Other than most boards with DDR4 the ASUS ZenWiFi BT8 cannot use the
"comb" DDR calibration option and needs only the "ddr4" option set
instead.
Build TF-A SPIM-NAND with UBI as well as to boot from RAM with
mtk_uartboot for MT7988 with DDR4 RAM.
Signed-off-by: John Crispin <john@phrozen.org>
Codename: Divo
Hardware specification:
========
SoC: Qualcomm IPQ6018
RAM: 512MB (2x ESMT 256MB DDR3L M15T2G16128A–DEBG2R)
NAND Flash: 512MB (Macronix MX30UF4G18AC or SK Hynix H27S4G8F2EDA-BC)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C-B0)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4@20/40/160 MHz (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 2x2@20/40/80 MHz (Qualcomm QCN5052 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 2x2@20/40 MHz (Qualcomm QCN5022 + Skyworks SKY8340-11)
IoT: Bluetooth 5 (CSR8811) - not implemented
LED: 1x RGB status + USB Blue (PWM)
USB: 1x USB 3.0
Button: WPS, Reset
Flash instructions (Without Serial):
========
Open Linksys Web UI - http://192.168.1.1/ca or http://linksysxxxxx.lan/ca depending on your setup.
xxxxx is the last 5 digits from the SN found on a sticker under the device.
Click on the Linksys Logo to by-pass smart app registration.
Login with your admin password. The default password can be found on the same sticker.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
Flash instructions (With Serial):
========
1. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd13 0 0
- nandwrite -p /dev/mtd13 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd15 0 0
- nandwrite -p /dev/mtd15 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel
2. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware:
- mtd -e kernel -n write FW_MR7500_1.1.12.211919_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MR7500_1.1.12.211919_prod.img alt_kernel
4. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
AQR firmware:
========
0. Firmware extracting:
To extract the firmware, use unblob (unblob.org)
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
2. Firmware updating:
Newer firmware (AQR114C.cld) is available in the latest OEM firmware (https://downloads.linksys.com/support/assets/firmware/FW_MR7500_1.1.12.211919_prod.img).
Copy AQR114C.cld to /lib/firmware/marvell
Link: openwrt#17428
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>
MR7500 features IPQ6018 which is CPPE, however, it also utilizes AQR114CB0 as WAN.
Previously, without this patch, aquantia_phy_api_ops was never called.
Therefore, enable `IN_AQUATIA_PHY` so that AQR PHY gets initialized properly on boot.
[ 3.973942] Aquantia AQR114C 90000.mdio-1:08: loading firmware version 'v5.6.5 Cybertan Divo 090221 14:43:44' from 'NVMEM'
[ 16.059953] aquantia_phy_api_ops_init[1485]:INFO:qca probe aquantia phy driver succeeded!
[ 17.930149] Aquantia AQR114C 90000.mdio-1:08: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:08, irq=POLL)
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>
Changes:
- Support of both Apple Silicon and Intel for macOS package.
- Add cvlan/svlan/tpmr capabilities.
- Disable LLDP in firmware for Intel X7xx cards on FreeBSD.
- Add lldpctl_watch_sync_unblock to liblldpctl.
- Add C++ wrapper for lldpctl.
Fix:
- Fix AppArmor policy for /run/lldpd/lldpd.socket.lock.
- Do not query stats for a down interface on Linux.
```
# lldpd -vv
lldpd 1.0.19
Built on 2025-03-24T17:43:44Z
Additional LLDP features: LLDP-MED, Dot1, Dot3, Custom TLV
Additional protocols: CDP, FDP, EDP, SONMP
SNMP support: no
Old kernel support: no (Linux 2.6.39+)
Privilege separation: enabled
Privilege separation user: lldp
Privilege separation group: lldp
Privilege separation chroot: /var/run/lldp
Configuration directory: /tmp
C compiler command: C compiler command is not available for reproducible builds
Linker command: Linker compiler command is not available for reproducible builds
```
Tested on: 24.10.0
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18345
Signed-off-by: Nick Hainke <vincent@systemli.org>
With this patch, iw can now scan APs in the 6 GHz band and shows
their operation parameters:
~~~
6 Ghz Operation Information: 0x0103070f06
Primary Channel: 1
Channel Width: 80+80 or 160 MHz
Regulatory Info: 0
Center Frequency Segment 0: 7
Center Frequency Segment 1: 15
Minimum Rate: 6
~~~
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/18240
Signed-off-by: Robert Marko <robimarko@gmail.com>
ChangeLog
417c2e3 libtracefs: version 1.8.1
41efd9e libtracefs: Add meson build targets to Makefile
310b796 libtracefs utest: Add better logic to cause missed events
b589e32 libtracefs: Add cpu-map sample to trace mapped buffer
4ede86e libtracefs: Enable mmapped ring buffer
e6737d4 libtracefs: Initialize val in build_filter()
590e452 libtracefs: Close dir in the error path in tracefs_event_systems()
0309a87 libtracefs: Close dir in the error path in tracefs_system_events()
f34fb1f libtracefs: Prevent memory leak in tracefs_dynevent_get_all()
48e906b libtracefs: my_yyinput() should return 0 when no data can be read
5e5b2a7 libtracefs: Prevent memory leak in tracefs_instance_create()
8f2593f libtracefs: Prevent a memory leak in open_cpu_files()
7d77b83 libtracefs: Prevent a memory leak in tracefs_system_events()
7fcd8d2 libtracefs: Prevent a memory leak in add_func_str()
a01d0ba libtracefs: Don't leak socket file descriptor in open_vsock()
efdf7f7 libtracefs: Prevent memory leak in tracefs_event_systems()
2342293 libtracefs: Prevent a memory leak in tracefs_synth_add_end_field()
1c95394 libtracefs: Prevent a memory leak in update_fields()
6b35665 libtracefs: Prevent memory leak in append_filer()
aecc0b7 libtracefs: Call va_end() before exiting tracefs_hist_set_sort_key()
a5e37f7 libtracefs: Add trace-mmap.c to meson build
8f62e96 libtracefs meson: Use SemVer in the build description
e04fa01 meson: Add utest option
fb213a4 libtracefs: Update trace_buffer_meta
04505a0 libtracefs utest: Include libgen.h for basename()
7b4a9c9 libtracefs utest: Define _LARGEFILE64_SOURCE for lseek64() with musl
ba75081 libtracefs utest: Add PATH_MAX if it is not already defined
5f27b7f libtracefs: Update the kbuf for previous read in trace_mmap_load_subbuf()
73ac9c1 libtracefs: Fix tracefs_instance_reset() of triggers
7d15d77 libtracefs meson: build tracefs-mmap by default
Link: https://github.com/openwrt/openwrt/pull/18349
Signed-off-by: Nick Hainke <vincent@systemli.org>
