Add missing kmod-7915e package to get both wireless interfaces working.
Link: https://github.com/openwrt/openwrt/issues/18690
Reviewed-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
Signed-off-by: Christoph Krapp <achterin@gmail.com>
(cherry picked from commit 0d6ba33181)
The WL-WN573HX3 is an AX3000 outdoor Access Point by WAVLINK,
also sold in Europe as 7Links WLR-1300 (ZX-5612).
Specifications:
- MT7981B + MT7976 AX3000 2x2 DBDC (160 MHz)
- 16 MiB SPI NOR, 256 MiB RAM
- Gigabit ethernet port, 802.3af PoE
- IP67 outdoor case for wall or pole mounting with
four single band RP-SMA fiberglass antennas (8 dBi)
Installation:
- OEM Web UI is at 192.168.30.1 which will forward to
http://netlogin.link (using a captive portal)
- login with default password `admin`
- skip setup wizard by navigating directly to
http://netlogin.link/html/meshUpgrade.html
- upload WN573HX3-sysupgrade.bin
- reset to factory defaults to discard OEM UCI settings
MAC address assignment:
LAN 80:xx:xx:76:xx:25 hw 0x44e
WLAN 2.4G 80:xx:xx:76:xx:27 factory 0x04 (label MAC)
WLAN 5G 82:xx:xx:46:xx:27
pair key 8a:xx:xx:76:xx:27 also on label, not used by OpenWrt
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Link: https://github.com/openwrt/openwrt/pull/18206
(cherry-picked from commit 907cb88e10)
Link: https://github.com/openwrt/openwrt/pull/18557
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Mercusys MR80X(EU) v3 router.
Device specification:
- SoC: Mediatek MT7981b, Cortex-A53, 64-bit
- RAM: 512MB
- Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
- Ethernet: 4x 100/1000 Mbps LAN1,LAN2,LAN3 & WAN
- Wireless: 2.4GHz (802.11 b/g/n/ax)
- Wireless: 5GHz (802.11 a/n/ac/ax)
- LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled LEDs
on ethernet ports
- Buttons: 1 (Reset)
- Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
slots contain "seconduboot" (also U-Boot 2022.01-rc4)
Installation (UART):
- Place OpenWrt initramfs-kernel image on tftp server with IP 192.168.1.2
- Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'.
- Set the uboot environment for startup.
setenv tp_boot_idx 0; setenv bootcmd bootm 0x46000000; saveenv
If the bootarg is set to boot from ubi1, also change it to ubi0.
- Load and run OpenWrt initramfs image.
setenv serverip 192.168.1.2; setenv ipaddr 192.168.1.1; tftpboot initramfs-kernel.bin; bootm
- Login as root via SSH (IP 192.168.1.1, port 22)
- Upload OpenWrt sysupgrade.bin image to the /tmp dir of the router
- Run sysupgrade:
sysupgrade -n /tmp/sysupgrade.bin
Recovery:
- Press Reset button and power on the router.
- Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware.
Stock layout:
0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"
ubi0/ubi1 format:
U-Boot at boot checks that all volumes are in place:
+-------------------------------+
| Volume Name: uboot Vol ID: 0|
| Volume Name: kernel Vol ID: 1|
| Volume Name: rootfs Vol ID: 2|
+-------------------------------+
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| label | 94:0C:xx:xx:xx:12 | label |
| WAN | 94:0C:xx:xx:xx:13 | label+1 |
| LAN | 94:0C:xx:xx:xx:12 | label |
| WLAN 2g | 94:0C:xx:xx:xx:11 | label-1 |
| WLAN 5g | 94:0C:xx:xx:xx:10 | label-2 |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file
"default-mac".
Signed-off-by: Schneider Azima <Schneider-Azima12@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/18181
(cherry picked from commit 7921e48d43)
Signed-off-by: Schneider Azima <Schneider-Azima12@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/18522
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
SOC: MediaTek MT7981b
RAM: 256MB DDR3
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7981b DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Installation
-----------------------------------------------------------
Vendor-UI Method
-----------------------------------------------------------
1. Download the OpenWrt initramfs.trx image.
2. Connect the PC via LAN to one of the yellow router ports and wait
until your PC to get a DHCP lease.
3. Browse to http://192.168.50.1
4. If your router is brand new, finish the setup process and log into
the Web-UI.
5. Navigate to Administration -> Firmware Upgrade and upload the
downloaded OpenWrt image.
6. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
-----------------------------------------------------------
TFTP Method
-----------------------------------------------------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.70/24. Rename the image to rtax52.bin.
2. Connect the PC with TFTP server to the RT-AX52.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
Conect to the serial console,
interrupt the autoboot process by pressing '4' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 rtax52.bin
$ bootm 0x46000000
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
---------------------------------------------------------------------------
Revert to stock firmware:
1: Download the rt-ax52 firmware from ASUS official website. Save
the firmware to tftp server directory and rename to RT-AX52.trx
2: Connect the PC with TFTP server to the RT-AX52.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
3: Conect to the serial console, power on again, interrupt the
autoboot process by pressing '4' when prompted.
$: ubi remove linux
$: ubi remove jffs2
$: ubi remove rootfs
$: ubi remove rootfs_data
$: ubi create linux 0x45fe000
$: reset
Then the dut will reboot,interrupt the autoboot process by
pressing '2' when prompted.
2: Load System code then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
$: enter y
you will see the follow, type enter directly:
Input device IP (192.168.1.1) ==:
Input server IP (192.168.1.70) ==:
Input Linux Kernel filename (RT-AX52.trx) ==:
4: wait for the device run up
Based on support for ASUS RT-AX52 by liudongdongdong7397
and trx image generation by remittor
Signed-off-by: Christoph Krapp <achterin@gmail.com>
(cherry picked from commit 50d9ca6e5a)
(remove factory image generation)
Signed-off-by: David Bauer <mail@david-bauer.net>
**Huasifei WH3000 eMMC / Fudy MT3000**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC.
MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ
**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8GB
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: power/reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1
**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.
**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.
**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-emmc-squashfs-sysupgrade.bin
```
**Factory MAC**
You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4`
```
dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C
```
**Enlarging a partition**
Though device has 8GB eMMC, it uses only 2GB `/dev/mmcblck0p6` as `rootfs` for `/rom` and `/overlay` leaving `/dev/mmcblck0p7` as empty unused space.
```
sgdisk -p /dev/mmcblk0
```
```
Disk /dev/mmcblk0: 15269888 sectors, 7.3 GiB
Sector size (logical/physical): 512/512 bytes
Disk identifier (GUID): 2BD17853-102B-4500-AA1A-8A21D4D7984D
Partition table holds up to 128 entries
Main partition table begins at sector 2 and ends at sector 33
First usable sector is 34, last usable sector is 14942174
Partitions will be aligned on 1024-sector boundaries
Total free space is 11197 sectors (5.5 MiB)
Number Start (sector) End (sector) Size Code Name
1 8192 9215 512.0 KiB 8300 u-boot-env
2 9216 13311 2.0 MiB 8300 factory
3 13312 21503 4.0 MiB 8300 fip
4 21504 29695 4.0 MiB 8300 config
5 29696 62463 16.0 MiB 8300 kernel
6 62464 4256767 2.0 GiB 8300 rootfs
7 4257792 14940159 5.1 GiB 8300
```
You can fix that by loading into `initramfs-kernel`, deleting empty `mmcblck0p7` partition and resizing `mmcblck0p6`
```
sysupgrade -F /tmp/openwrt-initramfs-kernel.bin
```
Install and run cfdisk
```
opkg update && opkg install cfdisk
cfdisk /dev/mmcblck0
```
- Select `mmcblck0p7` -> Delete
- Select `mmcblck0p6` -> Resize -> Write -> yes -> Quit
You will not see any difference in `cat /proc/partitions` after that but just flash a `sysupgrade` and you'll get the whole 7.3GB space for the `/overlay`.
Co-developed-by: hecatae <horus.ra@gmail.com>
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18220
(cherry picked from commit 99ea96c297)
Link: https://github.com/openwrt/openwrt/pull/18434
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This PR adds support for netis NX31 router.
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM : 256 MiB DDR3
- Flash : SPI-NAND 128 MiB (ESMT)
- WLAN : MediaTek MT7976CN dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x3 (LAN, MediaTek MT7531AE)
10/100/1000 Mbps x1 (WAN, SoC internal phy)
- USB : No
- Buttons : Mesh, Reset
- LEDs : 1x Power (blue), unmanaged
1x Status (blue), gpio-controlled
1x WiFi 2.4 GHz (blue), gpio-controlled
1x WiFi 5 GHz (blue), gpio-controlled
3x LAN activity (blue), switch-controlled
1x WAN activity (blue), gpio-controlled
- Power : 12 VDC, 1 A
Installation
------------
1. Connect to the router using ssh (user: admin, pass: web interface
password)
2. Make mtd backup:
cat /dev/mtd0 | gzip -1 -c > /tmp/mtd0_spi0.0.bin.gz
cat /dev/mtd1 | gzip -1 -c > /tmp/mtd1_BL2.bin.gz
cat /dev/mtd2 | gzip -1 -c > /tmp/mtd2_u-boot-env.bin.gz
cat /dev/mtd3 | gzip -1 -c > /tmp/mtd3_Factory.bin.gz
cat /dev/mtd4 | gzip -1 -c > /tmp/mtd4_FIP.bin.gz
cat /dev/mtd5 | gzip -1 -c > /tmp/mtd5_ubi.bin.gz
3. Download mtd backup from the /tmp dir of the router to your PC using
scp protocol
4. Upload OpenWrt 'bl31-uboot.fip', 'preloader.bin' images to the /tmp
dir of the router using scp protocol
5. Write FIP and BL2 (replace bootloader):
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-bl31-uboot.fip FIP
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-preloader.bin BL2
6. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
7. Erase 'ubi' partition and reboot the router:
mtd erase ubi
reboot
8. U-Boot automatically boot OpenWrt recovery image from tftp server to
the RAM
9. Upload OpenWrt 'sysupgrade.itb' image to the /tmp dir of the router
(IP: 192.168.1.1) using scp protocol
10. Connect to the router using ssh and run:
sysupgrade -n openwrt-mediatek-filogic-netis_nx31-squashfs-sysupgrade.itb
Return to stock
---------------
1. Unpack stock BL2 and FIP partitions backup
2. Upload stock BL2 and FIP partitions backup to the /tmp dir of the
router using scp protocol
3. Connect to the router using ssh and run:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd unlock FIP
4. Restore backup:
mtd write /tmp/mtd4_FIP.bin FIP
mtd write /tmp/mtd1_BL2.bin BL2
5. Erase ubi and reboot:
mtd erase ubi
reboot
6. Power off the router
7. Press Reset button and power on the router. Release the button after
~10 sec
8. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware
Recovery
--------
1. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
2. Press “Reset” button and power on the router. After ~10 sec release
the button.
3. Use OpenWrt initramfs system for recovery
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | dc:xx:xx:d1:xx:18 | label |
| WAN | dc:xx:xx:d1:xx:1a | label+2 |
| WLAN 2g | de:xx:xx:11:xx:19 | |
| WLAN 5g | de:xx:xx:71:xx:19 | |
+---------+-------------------+-----------+
The LAN MAC was found in 'Factory', 0x1fef20
The WAN MAC was found in 'Factory', 0x1fef26
The WLAN 2g/5g MAC prototype was found in 'Factory', 0x4
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18324
(cherry picked from commit d8002cb627)
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18438
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With upstream changes hitting kernel 6.4 the dtb for u7623 ends up with
both mac (gmac) disabled, since this is now the default status in
mt7623.dtsi. Fix this by including mt7623a.dtsi (which already has all
necessary bits) and enabling all revlevant ports. This will also do
a side hustle of assigning proper clocks for power controller and
specifying proper power domain for few devices.
Link: https://lore.kernel.org/all/20230210182505.24597-1-arinc.unal@arinc9.com
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250304164507.60511-2-tmn505@terefe.re/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit adc4d95c74)
This board is also as known as SuperElectron ZN-M5 and ZN-M8. However,
for ZN-M5 and ZN-M8, there's another version uses ZX279128 as CPU
chip, which is unsupported.
You can check it in "高级设置" > "系统日志" > "内核日志" page from webUI.
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS
Power: DC 12V 1A
Stock layout flash instructions:
Login into webUI and upload sysupgrade firmware in "系统管理" > "升级固件" page.
Remember to unselect "保留配置" ("Keep configurations") first before doing that.
OpenWrt U-Boot layout flash instructions:
1. Flash stock layout firmware first.
2. Connect to the device via SSH, and backup everything,
especially 'Factory' partition.
3. Unlock MTD partitions:
opkg update && opkg install kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
4. Write new BL2 and FIP:
mtd write openwrt-mediatek-filogic-cmcc_a10-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cmcc_a10-ubootmod-bl31-uboot.fip FIP
5. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/18121
(cherry picked from commit 96c6608346)
[sync uboot defconfigs with 24.10 branch, change apk to opkg]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/18218
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
I selected one subtarget after the other and refreshed their
configuration using this command:
make kernel_oldconfig CONFIG_TARGET=subtarget
For MT7629 I had to re-add CONFIG_LEDS_SMARTRG_LED manually.
Otherwise, building MT7629 with ALL_KMODS we get prompted for
LEDS_SMARTRG_LED and this will break CI and in future buildbot
compilation. See commit 6bdea8c7bd ("mediatek: mt7629: 6.6: disable
LEDS_SMARTRG_LED by default") for more details.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/18182
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5013efc4f9)
Specification:
* Mediatek MT7981BA
* 256 MB SPI-NAND
* 512 MB DDR4 RAM
* MT7976CN DBDC AX Wi-Fi
* MediaTek MT7531AE (3x LAN Gigabit ports) + Internal Gbe Phy (1x WAN Gigabit port)
* 4x LED (power, internet, fn, wifi)
* 3x buttons (wps, fn, reset)
* 1x USB 3.0 port
Serial Interface:
* 3 Pins GND, RX, TX
* Settings: 115200, 8N1
Notes:
* The device supports dual boot mode
* Fn led reassigned to wlan 2.4
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-mediatek-filogic-keenetic_kn-3811-squashfs-factory.bin"
to "KN-3811_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17135
(cherry picked from commit d087a79b7b)
Link: https://github.com/openwrt/openwrt/pull/18055
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
- MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
- 512MB RAM
- 128MB SPI NAND
- 2 LEDs (green, orange)
- 3 buttons (fn, reset, wps)
- 2 2.5Gbit ethernet ports based on Airoha EN8811H phy
Serial Interface:
- 3 Pins GND, RX, TX
- Settings: 115200, 8N1
Notes:
- The device supports dual boot mode
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-mediatek-filogic-keenetic_kn-3911-squashfs-factory.bin"
to "KN-3911_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16830
(cherry picked from commit 5a4eb56a7b)
Link: https://github.com/openwrt/openwrt/pull/18055
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Apply "u-boot-dont-touch-spi-nand" to ASUS RT-AX59U, ASUS TUF-AX4200 as
well as ASUS TUF-AX6000 routers to prevent U-Boot from wiping MTD
child nodes from DT.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 4387de9445)
ASUS makes use of U-Boot's fdt_fixup_mtdparts() function which applies
the partitions defined in U-Boot's mtdparts and mtdids environment
variables to the devicetree passed over to Linux.
The undesired side-effect is that in this way also all additional
properties and child nodes get wiped, preventing NVMEM cells to be
defined for MTD partitions or UBI volumes.
To work-around this issue, add an additional compatible string
'u-boot-dont-touch-spi-nand' which can be used instead of 'spi-nand' in
case the replacement of the MTD partitions by U-Boot should be skipped
alltogether.
In practise this is mostly relevant for SPI-NAND which anyway comes only
with two partitions nowadays: 'Bootloader' and 'UBI_DEV'. Hence this
work-around is applicable for SPI-NAND only. Similar work-arounds for
other MTD devices can be created as well should they actually be needed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit c48afca32c)
This commit fixes nmbm configuration mismatch error on Xiaomi AX3000t
with Winbond W25N01KVZEIR spi-nand:
'''
[ 0.786783] NMBM configuration mismatch
'''
Root cause:
1. U-Boot W25N01KV spi-nand driver ia compiled with 64B OOB size for the
chip and store this size in the nmbm signature;
2. Linux W25N01KV driver use 96B OOB.
The change doesn't affect AX3000t variants with other spi-nand chips
(ESMT, Foresee) because their Linux drivers use 64B OOB.
Fixes: openwrt#16972
Tested-by: Aleksandr Danilov <sc16me@gmail.com>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17549
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3299d19c01)
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Two commits which made their way into Linux stable broke the SATA
support on the BPi-R64.
Fix this by reverting a node rename which broke DT-overlay application
and import a (still pending) patch re-adding the 'syscon' compatible to
the pciesys clock-controller which also contains phy-mode bits
referenced by the ahci_mtk driver expecting to access them using
syscon_regmap_lookup_by_phandle().
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 69890e16b3)
Fixed interrupt support for 2.5G PHY.
Removed useless phy-mode on phy node.
Tested on Cudy TR3000.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 82b69dfaf6)
Same as commit 3674689, correct 'buswidth' to 'bus-width'.
Move the nmbm properties outside the partition definition.
Change uppercase to lowercase, add missing read-only flag.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit ab375a3484)
the wifi leds of the wax206 were not reacting.
This patch enables the green leds to show activity, as the blue ones are very bright.
Also set the label-mac to the gmac0
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17694
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 9ada8578fd)
This commit fixes Xiaomi AX3000t soft bricks. Issue affects at least rd23
model (Global version) users:
Link: https://forum.openwrt.org/t/openwrt-support-for-xiaomi-ax3000t/180490/452
I also found that these nvram settings are wrong for the rd23 model and
U-Boot erase them:
'''
flag_try_sys1_failed 8
flag_try_sys2_failed 8
'''
As a result, platform.sh -> xiaomi_initial_setup() function sometimes ends
early without applying settings for the rd23 model.
RD03 model strategy:
1. Don't touch values those were set up by platform.sh ->
xiaomi_initial_setup() function
RD23 model strategy:
1. Apply correct nvram settings at every boot
2. Use bulk fw_setenv call
I didn't find opened issue for AX3000t. Similar AX3200 issue:
Link: https://github.com/openwrt/openwrt/issues/16347
So, other Xiaomi devices (e.g. Xiaomi WR30U) may also require fix.
Fixes: 7dbcc1215a ("mediatek: filogic: add support for Xiaomi AX3000T")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17580
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 42a253c7e8)
This commit replaces multiple fw_setenv calls by the bulk one to reduce
flash writes.
Thanks @Linaro1985 for the idea.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17580
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit a6b0abf466)
The WAX220 does have a 2.4GHz and 5GHz wifi led, which was set to trigger on netdev before.
This commit changes this to trigger on activity of the respective radio
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17627
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 99431e3150)
Define EX5601-T1 and T-56 as alternative name, to explicitly show
the device is supported using existing image. EX5601-T1 does not
have the option to switch between WAN/SFP port. The switch port
is hardwired to the WAN port. The Zyxel T-56 is the odido-branded
version of the EX5601-T1.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17615
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3d63a41ffa)
Hardware:
SoC: MT7981b
RAM: 512 MB
Flash: 256 MB SPI NAND
Ethernet:
1x2.5Gbps (rtl8221b)
WiFi: 2x2 MT7981
Button: Reset
LED: 1x multicolor
Installation
------------
At the moment, firmware installation is only possible via a transition firmware.
It's can be requested from the manufacturer by email to support@cudy.com
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17225
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6992d6e51a)
I think I implemented the U-Boot handling incorrectly on M30 (saw the issue while porting M60 to OpenWrt). Maybe someone with more U-Boot experience can have a look at it.
What I understood until now:
Before flashing, `sw_tryactive` must be set to 0 because OpenWrt runs on partition 0
During reset after flashing, U-Boot executes the following line:
`boot_rd_auto_sw_img=if itest.s ${sw_tryactive} == 2; then run boot_by_part; else run boot_by_tryactive; fi`
As `sw_tryactive` was set to 0 before flashing, `boot_by_tryactive` will be executed:
`boot_by_tryactive=if itest.s ${sw_tryactive} == 0; then setenv sw_tryactive 2; setenv sw_active 1; saveenv; run ub0; else setenv sw_tryactive 2; setenv sw_active 2; saveenv; run ub1; fi`
As `sw_tryactive` was set to 0 before flashing, `sw_active` will be set to 1 and `ub0` will be executed:
`ub0=setenv bootpart 0; mtkboardboot; run ub0to1; uip main; reset`
If the OpenWrt boot is successful, `ub0to1` and `uip` main will never be executed. Only in case OpenWrt cannot be loaded, `mtkboardboot` will return and the fallback `ub0to1` is executed.
Conclusion: It's sufficient to set `sw_tryacitve` to 0 before flashing, the added code in `target/linux/mediatek/filogic/base-files/etc/init.d/bootcount` is useless.
In the worst case (/proc/cmdline doesn't contain `bootpart=ubi0` as expected), the bootpart variable would be set to 1 and causes starting the firmware from the second partition instead of the one on the first partition.
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17298
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 70610a5240)
This commit adds kmod-leds-ktd202x to the OpenWrt image for the device
"Acer Connect Vero W6m" which is equipped with one KTD2026 controlling the
device's status LED via I2C.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16860
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e44180d45c)
Specification:
- MT7986 CPU using 2.4GHz and 5GHz WiFi (both AX)
- MT7531 switch
- 512MB RAM
- 128MB NAND flash (MX35LF1GE4AB-Z4I) with two UBI partitions with identical size
- 1 multi color LED (red, green, blue, white) connected via GCA230718 (Same as D-Link M30 A1)
- 3 buttons (WPS, reset, LED on/off)
- 1x 2.5 Gbit WAN port with Maxlinear GPY211C
- 4x 1 Gbit LAN ports
Disassembly:
- There are five screws at the bottom: 2 under the rubber feet, 3 under the label.
- After removing the screws, the white plastic part can be shifted out of the blue part.
- Be careful because the antennas are mounted on the side and the top of the white part.
Serial Interface
- The serial interface can be connected to the 4 pin holes next to/under the antenna cables.
- Note that there is another set of 4 pin holes on the side of the board, it's not used.
- Pins (from front to rear):
- 3.3V (do not connect)
- TX
- RX
- GND
- Settings: 115200, 8N1
MAC addresses:
- MAC address is stored in partition "Odm" at offset 0x81 (for example XX:XX:XX:XX:XX:52)
- MAC address on the device label is ODM + 1 (for example XX:XX:XX:XX:XX:53)
- WAN MAC is the one from the ODM partition (for example XX:XX:XX:XX:XX:52)
- LAN MAC is the one from the ODM partition + 1 (for example XX:XX:XX:XX:XX:53)
- WLAN MAC (2.4 GHz) is the one from the ODM partition + 2 (for example (XX:XX:XX:XX:XX:54)
- WLAN MAC (5 GHz) is the one from the ODM partition + 5 (for example (XX:XX:XX:XX:XX:57)
Flashing via OEM web interface:
- Currently not supported because image crypto is not known
Flashing via recovery web interface:
- This is only working if the first partition is active because recovery images are always flashed to the active partition and OpenWrt can only be executed from the first partition
- Use a Chromium based browser, otherwise firmware upgrade might not work
- Recovery web interface is accessible via 192.168.200.1 after keeping the reset button pressed during start of the device until the LED blinks red
- Upload the recovery image, this will take some time. LED will continue flashing red during the update process
- The after flashing, the recovery web interface redirects to http://192.168.0.1. This can be ignored. OpenWrt is accessible via 192.168.1.1 after flashing
- If the first partition isn't the active partition, OpenWrt will hang during the boot process. In this case:
- Download the recovery image from https://github.com/RolandoMagico/openwrt/releases/tag/M60-Recovery-UBI-Switch (UBI switch image)
- Enable recovery web interface again and load the UBI switch image. This image works on the second partition of the M60
- OpenWrt should boot now as expected. After booting, flash the normal OpenWrt sysupgrade image (for example in the OpenWrt web interface)
- Flashing a sysupgrade image from the UBI switch image will make the first partition the active partition and from now on, default OpenWrt images can be used
Flashing via Initramfs:
- Before switching to OpenWrt, ensure that both partitions contain OEM firmware.
- This can be achieved by re-flashing the same OEM firmware version again via the OEM web interface.
- Flashing via OEM web interface will automatically flash the currently not active partition.
- Open router, connect serial interface
- Start a TFTP server at 192.168.200.2 and provide the initramfs image there
- When starting the router, select "7. Load Image" in U-Boot
- Settings for load address, load method can be kept as they are
- Specify host and router IP address if you use different ones than the default (Router 192.168.200.1, TFTP server 192.168.200.2)
- Enter the file name of the initramfs image
- Confirm "Run loaded data now?" question after loading the image with "Y"
- OpenWrt initramfs will start now
- Before flashing OpenWrt, create a backup of the "ubi" partition. It is required when reverting back to OEM
- Flash sysupgrade image to flash, during flashing the U-Boot variable sw_tryactive will be set to 0
- During next boot, U-Boot tries to boot from the ubi partition. If it fails, it will switch to the ubi1 partition
Reverting back to OEM:
- Boot the initramfs image as described in "Flashing via Initramfs" above
- Copy the backed up ubi partition to /tmp (e.g. by using SCP)
- Write the backup to the UBI partition: mtd write /tmp/OpenWrt.mtd4.ubi.bin /dev/mtd4
- Reboot the device, OEM firmware will start now
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17296
(cherry picked from commit b3ce08e0b6)
Link: https://github.com/openwrt/openwrt/pull/17363
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The board has been redesigned due to previous hardware bugs
(with other reasons maybe).
Changes in new board:
- Added a gpio beeper
- Added a Atmel i2c eeprom
- Added a Atmel i2c ECC accelerator
- Added a Philips RTC module
- Added two RS485
- Removed WPS button
- Replaced USB3 port with M.2 B-key for LTE modules
- Swapped GbE LEDs gpio
Also assigned wifi mac with nvmem binding, added iface setup for failsafe,
increased phy assert time for rtl8221b, and updated LED labels.
Keeping compatibility for old version is not necessary here as only
few samples were sent to those interested in it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17253
(cherry picked from commit 5a7fb834c7)
Link: https://github.com/openwrt/openwrt/pull/17348
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The device path to the devices changed. Migrate the wifi
configurations from the old path to the new one. This is needed to
migrate Wireless configurations from OpenWrt 23.05 to OpenWrt 24.10.
This script is based on these two files:
target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate
target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate
Fixes: 0ef9274721 ("mediatek: filogic: move mt7981 on-SoC blocks to "soc" node in DT")
Fixes: https://github.com/openwrt/openwrt/issues/17174
Link: https://github.com/openwrt/openwrt/pull/17210
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f8b93e2d12)
