This commit adds support for Buffalo WSR-6000AX8 and AX8P models.
Hardware
--------
SOC: MediaTek MT7986B
RAM: 512MB
FLASH: 128MB SPI-NAND (Winbond)
WIFI 2.4G: (Embedded in SOC) b/g/n/ax, MIMO 4x4
WIFI 5G: (Embedded in SOC) a/n/ac/ax, MIMO 4x4
ETHERNET: 2.5GbE MaxLinear GPY211C (eth1: WAN)
ETHERNET: MediaTek MT7531AE 3xGbE (eth0: LAN1, LAN2, LAN3)
UART: 3.3V 115200 8N1
Serial(UART) Pin Layout
-----------------------
+-------+-------+-------+-------+
J4 | RX | TX | GND |(3.3V) |
+-------+-------+-------+-------+
(Bottom Side)
MAC Address Table
-----------------
lan1-3: board_data 0x4(text)
eth1/WAN: board_data 0x4(text)
WIFI 2.4G: lan1 + 2
WIFI 5G: lan1 + 9
Installation
------------
1. Set up a TFTP server with the IP address "192.168.11.2".
2. Rename the OpenWrt initramfs image to "linux.ubi-recovery" and place it
in the TFTP server's root directory.
3. While holding down the AOSS button, power on the WSR-6000AX8 (or AX8P).
4. The device will automatically download the initramfs image
from the TFTP server and boot into it.
5. Once booted, run "sysupgrade -n" using the OpenWrt sysupgrade image
to complete the installation.
Recovery
--------
1. Decrypt the official firmware image using "buffalo-enc".
example:
$ buffalo-enc -d -i wsr_6000ax8_jp_100 -o wsr_6000ax8_jp_100.dec \
-l -O 0xc8
2. Run "sysupgrade -F -n" with the decrypted image.
Signed-off-by: Shin Sato <shin.sugar.ssyysy2021@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/13107
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a smart door lock device equipped with OpenWrt 14.07 OEM
modified version Qdwrt
The OEM has closed down, This commit is intended to maximize the
remaining value of these devices. It can flash OpenWrt to become
an AP
Specification:
- SoC: MediaTek MT7628NN
- Flash: 8 MB
- RAM: 64 MB
- Power: DC 5V - 25V
- Ethernet: 1 x RJ45 (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only
- On-Board LED:
Status 1: GPIO/43 active-low
Status 2: GPIO/44 active-low
Power: AlwaysOn
- Button:
WPS / RESET: GPIO/14 active-low
- Bluetooth: CC2541 via UART1 (ttyS1) and GPIO/26-29
- RFID: MF RC522 on I2C@28
- RTC: DS1339 on I2C@68
- Shell (via CON1 cable)
- LED (Swipe card area):
- Green GPIO/3 active-high
- Red GPIO/11 active-high
- Matrix keypad: (active-low)
GPIO/20 GPIO/21 GPIO/19 (Rows)
GPIO/24 1 2 3
GPIO/25 4 5 6
GPIO/22 7 8 9
GPIO/23 BACK 0 ENTER
(Cols)
- UART: 1 x UART on PCB - 57600 8N1
- GPIO Relay: GPIO/42 active-high
- GPIO Buzzer: GPIO/15 active-high
Warning:
The original firmware does not use the device tree.
This device tree is written based on the content of /sys/devices/platform
and has been tested
Note:
- On the device, matrix keypad rows actually are columns, and the columns actually are rows
- The key code of the CLEAR key of the matrix keypad is BACK in the original firmware.
Issue:
- No drivers in mainline kernel for RFID and Bluetooth.
Flash Instruction:
Using SSH/Telnet:
1. Connect the board to the computer via RJ45 Ethernet
2. Login 10.10.10.1 with root password "szqdingnet123" (SSH Port 22, Telnet Port 9900)
3. Download openwrt firmware on the computer.
4. Setup a http server on computer. And use wget download openwrt firmware from computer
5. Use command "mtd -r write openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin firmware"
to flash
Using U-Boot WebUI:
1. Configure PC with a static IP address 10.10.10.2/24.
2. Open http://10.10.10.1
3. Use "mkqdimg -B qc202 -f openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin" to
make image.
4. Upload factory.bin via U-Boot WebUI.
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-qianding-smart-locker-and-flash.html
Original U-Boot firmware image tools:
https://gitlab.com/CoiaPrant/mkqdimg
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17471
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for the Lunzn FastRhino R66S board.
Tested-by: Francisco G Luna <frangonlun@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/19990
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
While these boards have an at24 EEPROM for storing the MAC address,
early revisions (up until about 2017) did not contain actual addresses.
Create a random address to have ethernet function properly in u-boot.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This commit adds ddr3 build for the ddr3 variant of the CMCC RAX3000Me
router.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19760
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Airoha AN8855 switch. Some CMCC RAX3000Me hw
revisions are shipped with Airoha switch.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19760
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa E52C is a compact network computer using the Rockchip RK3582
SoC.
- https://radxa.com/products/network-computer/e52c
Hardware
--------
- Dual Cortex-A76 and Quad Cortex-A55 CPU
- 5 TOPS NPU
- 2/4/8GB LPDDR4 RAM
- 16/32/64GB on-board eMMC
- microSD card slot
- 2x 2.5 Gigabit Ethernet ports
- USB 3.1 Gen1 Type-A HOST/OTG port
- USB Type-C debug port
- USB Type-C power port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/19867
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 5C (Lite) is a single board computer using the Rockchip
RK3588S2 (RK3582) SoC.
- https://radxa.com/products/rock5/5c
Hardware
--------
- Quad (Dual) Cortex-A76 and Quad Cortex-A55 CPU
- Mali-G610 MP4 GPU (5C only)
- 6 (5) TOPS NPU
- 1/2/4/8/16/32GB LPDDR4X RAM
- eMMC/SPI NOR flash connector
- microSD card slot
- Wi-Fi 6 (AIC8800D80, not yet supported)
- Gigabit Ethernet port with PoE (additional PoE HAT required)
- USB 3.1 Gen1 Type-A HOST/OTG port
- USB 3.1 Gen1 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- FPC connector with PCIe 2.1 x1
- PWM fan connector
- 20x2 pin header
- USB Type-C power port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/19867
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 5 ITX(+) is a Mini-ITX form factor computer using the
Rockchip RK3588 SoC.
- https://radxa.com/products/rock5/5itx
- https://radxa.com/products/rock5/5itxp
Hardware
--------
- Quad Cortex-A76 and Quad Cortex-A55 CPU
- Mali-G610 MP4 GPU
- 6 TOPS NPU
- 4/8/16/24/32GB LPDDR5 RAM
- on-board eMMC
- 16MB SPI NOR flash
- microSD card slot
- 2x 2.5 Gigabit Ethernet ports with PoE (additional PoE module required)
- USB 3.1 Gen1 Type-C HOST/OTG port
- 4x USB 3.1 Gen1 Type-A HOST ports
- 2x USB 2.0 Type-A HOST ports
- M.2 M Key connector with PCIe 3.0 x2
- 4x SATA connectors (ITX only)
- 2nd M.2 M Key connector with PCIe 3.0 x2 (ITX+ only)
- M.2 E Key connector with PCIe 2.1 x1 and USB 2.0
- RTC battery socket for CR1220
- 4pin PWM fan connector
- Serial console pin header
- Front panel pin headers
- 24pin ATX power connector
- 5525 12V DC jack
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/19867
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 5B+ is a single board computer using the Rockchip
RK3588 SoC.
- https://radxa.com/products/rock5/5bp
Hardware
--------
- Quad Cortex-A76 and Quad Cortex-A55 CPU
- Mali-G610 MP4 GPU
- 6 TOPS NPU
- 4/8/16/24/32GB LPDDR5 RAM
- 16/32/64/128/256GB on-board eMMC (optional)
- 16MB SPI NOR flash
- microSD card slot
- Wi-Fi 6 (Realtek RTW8852BE)
- 2.5 Gigabit Ethernet port with PoE (additional PoE HAT required)
- USB 3.1 Gen1 Type-C HOST/OTG port
- 2x USB 3.1 Gen1 Type-A HOST ports
- 2x USB 2.0 Type-A HOST ports
- 2x M.2 M Key connectors with PCIe 3.0 x2
- M.2 B Key connector
- SIM card slot
- RTC battery connector
- PWM fan connector
- 20x2 pin header
- USB Type-C power port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/19867
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
wmcpu_emi node was removed in commit:
b286fd8a39 ("uboot-mediatek: adjust the reserved memory regions")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19855
Signed-off-by: Robert Marko <robimarko@gmail.com>
* Increase mt7986 ATF reserved memory to 256 kiB to follow the linux
kernel and Trusted Firmware-A changes.
* Remove unnecessary reserved memory region for the WiFi hardware. The
u-boot can not drive the WiFi hardware. Hence we don't need to keep
this memory region.
* Remove useless node labels and update comments.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19741
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
OpenWrt layerscape target does not use this command. If the host is
missing gnutls, this tool will fail to build. Fix build error:
tools/mkeficapsule.c:20:10: fatal error: gnutls/gnutls.h: No such file or directory
20 | #include <gnutls/gnutls.h>
| ^~~~~~~~~~~~~~~~~
Fixes: c773c3f4d3 ("uboot-layerscape: bump to lf-6.12.20-2.0.0")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19836
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now devicetrees imported from Linux kernel release are used, so update
DEVICE_TREE to use correct path. A patch was backported to increase
SYS_MALLOC_F_LEN for stm32mp13 (more alloc space is needed due to SCMI
update to protocol v2.0).
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/19779
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Modernize the target slightly to use kernel+dtb FIT images in all
subtargets. LZMA compression will be used for the cortexa53 devices,
and we'll stay conservative and use gzip for the cortexa7/a8 devices
due to performance differences.
Tested-on:
- Linksprite pcDuino v2 (cortexa8 / A10)
- Olinuxino Micro (cortexa7 / A20)
- Banana Pi M2 Berry (cortexa7 / V40)
- Banana Pi P2 Zero (cortexa7 / H2+)
- Xunlong Orange Pi 2 (cortexa7/ H3)
- OrangePi PC Zero 2 (cortexa53 / H616)
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This newly supported device has the same env partition size and
offset as SIMAX1800T.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19455
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
GS1900-48 is missing from package/boot/uboot-tools/uboot-envtools/files/realtek, so add it to be consistent.
Signed-off-by: Joe Holden <jwh@zorins.us>
Link: https://github.com/openwrt/openwrt/pull/19596
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update package to the latest stable version.
All patches automatically refreshed.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/19621
Signed-off-by: Nick Hainke <vincent@systemli.org>
Fix the crash and warnings for the newly introduced env on mtd
implementation. Also backport an out-of-bound access fix for the
"askenv" command.
Fixes: 41a9c9de66 ("uboot-mediatek: update to v2025.07")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
In the upstream implementation of env in mtd, ENV_MTD_NAME symbol
was renamed to ENV_MTD_DEV. Therefore, we have to adjust the symbol
to make it work properly. ENV_SIZE_REDUND symbol will be removed
in this patch because the upstream env in mtd implementation no
longer requires it.
Fixes: 41a9c9de66 ("uboot-mediatek: update to v2025.07")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
The popular Mediatek target has many u-boot modified devices. This
change can keep the u-boot source code tidy.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Partially revert commit 332645a610 ("uboot-mediatek: sync with
mtk-openwrt/u-boot 20250711") by dropping unused PHY drivers which come
with large embedded firmware (and are hence inacceptable for upstream)
and restoring our previous version of the Airoha EN8811H driver which is
known to work and load firmware from the eMMC boot1 hardware partition
instead of embedding it in the driver.
In future we may switch to the upstream Airoha EN8811H driver which
allows loading the firmware either from a filesystem or overloading the
en8811h_read_fw() for board which may eg. store that firmware directly
inside a eMMC hardware partition or UBI volume, like the BPi-R3 mini
does.
See also:
https://patchwork.ozlabs.org/project/uboot/patch/20250615131243.30770-1-lucienzx159@gmail.com/
Fixes: 332645a610 ("uboot-mediatek: sync with mtk-openwrt/u-boot 20250711")
Reported-by: Adrian Bente
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update mediatek arm-trusted-firmware to the latest version.
Remove upstream patch:
0004-mediatek-snfi-fix-return-code-when-reading.patch
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
The build error has been fixed by the upstream commit:
03e598263e38 ("tools: fix build without LIBCRYPTO support")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Most ramips target devices use the legacy uImage format. This
patch extends the imsz/imszb commands to support detecting the
image size of legacy uImage.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Add back the default LK image header to generate u-boot-mtk.bin. This
is the default behavior before u-boot v2022.01. If "u-boot-mtk.bin"
doesn't boot, please try "u-boot.bin" and report it.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Update to the latest version.
Suppressed patch:
100-04-env-add-support-for-generic-MTD-device.patch[1]
[1] 03fb08d4ae
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
