Currently, building at91 subtargets via image builder will fail as the
required built at91bootstrap is not present in the image builder at all
since its presumed to be in the binary directory which obviously does not
exist yet.
So, lets install the at91bootstrap binary into image staging directory and
use that instead
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, building at91 subtargets via image builder will fail as the
required built u-boot is not present in the image builder at all since its
presumed to be in the binary directory which obviously does not exist yet.
So, lets install the u-boot binary into image staging directory and use
that instead.
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
Netgear WAX610 / WAX610Y is a 802.11ax AP claiming AX1800 support.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512MB
* Storage: Winbond W29N01HZBINF 128MB NAND
* Ethernet:
* 2.5GbE RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Power: Dual-color LED (Green / Orange), Single-color LED (Blue)
* Ethernet: Dual-color LED (Green / Orange)
* 2.4Ghz WiFi: 2x Single-color LED (Blue, Green)
* 5Ghz WiFi: 2x Single-color LED (Blue, Green)
* Buttons:
* 1x Reset
* UART: 4-pin populated header
* Pinout 1 - VCC, 2 - GND, 3 - TX, 4 - RX
Installation:
=============
Web UI method
-------------
Set up the device using the stock web UI in local management mode.
Download the ui-factory.tar image.
* Enter the Management tab
* Select Maintenance->Upgrade->Firmware Upgrade
* Ensure the "Upgrade Options" field has "Local" selected
* Click "Browse File" and select the image
* Click "Upgrade" (NOT "Upgrade Now") at the bottom of the page
The device will install the image but reboot back into the vendor
firmware. Return the to Firmware Upgrade page as above and select
"Boot up Backup Firmware". The device should reboot into OpenWRT.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot netgear_wax610-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the command line.
Signed-off-by: Erik Servili <serverror@serverror.com>
Link: https://github.com/openwrt/openwrt/pull/18377
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath10k dt-binding property "qcom,coexist-support" was
explicitly defined as type uint8 since upstream commit
ed09c61eb19d ("dt-bindings: net: Convert ath10k to YAML").
Therefore, this hack patch no longer makes sense.
Link: ed09c61eb1
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18393
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport two commits to resolve issues with ath1kk causing it to fail
driver registration on iommuless systems with DRAM outside of 32bit
addressing such as a 4GiB imx8mm:
commit 1bcd20981834 ("wifi: ath11k: Fix DMA buffer allocation
to resolve SWIOTLB issues")
commit eeadc6baf8b3 ("wifi: ath11k: Use dma_alloc_noncoherent
for rx_tid buffer allocation")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/17751
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit 1375a7bae0.
This version does not activate the CONFIG_LEDS_CLASS_MULTICOLOR option,
this option is controlled by the generic target configuration.
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/17277
[Reword commit message]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Although ath10k pre-calibration data and board description file
have similar data structures, they are completely different things.
Therefore, let's remove these incorrect and confusing links.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18069
Signed-off-by: Robert Marko <robimarko@gmail.com>
This new version fixes some memory leak and NULL pointer issues.
Upstreamed patches:
[1] 010-api_update.patch
[2] 201-wifi-ath10k-add-LED-and-GPIO-controlling-support-for.patch
The new 003 patch was introduced to fix the build error on old LTS
kernel. The patch 004 was used to fix the issue of IPQ4019 radio
not being able to start.
Tested on QCA9882 and IPQ4019.
[1] bca8bc0399
[2] 8e1debd824
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18368
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove settings and depends that are not used anywhere.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18291
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
b6e5157527d3 fw4: fix reading kernel version
42d3b3d4ca21 fw4: allow family any for ipsets not matching IP addresses
edfdfc6df484 Revert "fw4: allow family any for ipsets not matching IP addresses"
97962771aa3c config: drop to-be-forwarded-nowhere packets on wans
00fc6943a297 init: remove unnecessary stop logic
ad3cba79c192 fw4: allow family any for ipsets not matching IP addresses
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
[fix PKG_MIRROR_HASH]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18283
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix compilation error for old stable version caused by
genlmsg_multicast_allns backport fix pushed middle version.
Version 5.15 version 0-169, 6.1 version 0-115, 6.6 version 0-58 have the
old genlmsg_multicast_allns version with flags variable.
Compiling backport project with these version result in a compilation
error. To handle this, introduce a backport function for the affected
kernel version.
Link: https://github.com/openwrt/openwrt/pull/18373
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add U-Boot build for the ASUS ZenWiFi BT8 intended to replace the
stock loader.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Other than most boards with DDR4 the ASUS ZenWiFi BT8 cannot use the
"comb" DDR calibration option and needs only the "ddr4" option set
instead.
Build TF-A SPIM-NAND with UBI as well as to boot from RAM with
mtk_uartboot for MT7988 with DDR4 RAM.
Signed-off-by: John Crispin <john@phrozen.org>
Codename: Divo
Hardware specification:
========
SoC: Qualcomm IPQ6018
RAM: 512MB (2x ESMT 256MB DDR3L M15T2G16128A–DEBG2R)
NAND Flash: 512MB (Macronix MX30UF4G18AC or SK Hynix H27S4G8F2EDA-BC)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C-B0)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4@20/40/160 MHz (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 2x2@20/40/80 MHz (Qualcomm QCN5052 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 2x2@20/40 MHz (Qualcomm QCN5022 + Skyworks SKY8340-11)
IoT: Bluetooth 5 (CSR8811) - not implemented
LED: 1x RGB status + USB Blue (PWM)
USB: 1x USB 3.0
Button: WPS, Reset
Flash instructions (Without Serial):
========
Open Linksys Web UI - http://192.168.1.1/ca or http://linksysxxxxx.lan/ca depending on your setup.
xxxxx is the last 5 digits from the SN found on a sticker under the device.
Click on the Linksys Logo to by-pass smart app registration.
Login with your admin password. The default password can be found on the same sticker.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
Flash instructions (With Serial):
========
1. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd13 0 0
- nandwrite -p /dev/mtd13 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd15 0 0
- nandwrite -p /dev/mtd15 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel
2. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware:
- mtd -e kernel -n write FW_MR7500_1.1.12.211919_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MR7500_1.1.12.211919_prod.img alt_kernel
4. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
AQR firmware:
========
0. Firmware extracting:
To extract the firmware, use unblob (unblob.org)
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
2. Firmware updating:
Newer firmware (AQR114C.cld) is available in the latest OEM firmware (https://downloads.linksys.com/support/assets/firmware/FW_MR7500_1.1.12.211919_prod.img).
Copy AQR114C.cld to /lib/firmware/marvell
Link: openwrt#17428
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>
MR7500 features IPQ6018 which is CPPE, however, it also utilizes AQR114CB0 as WAN.
Previously, without this patch, aquantia_phy_api_ops was never called.
Therefore, enable `IN_AQUATIA_PHY` so that AQR PHY gets initialized properly on boot.
[ 3.973942] Aquantia AQR114C 90000.mdio-1:08: loading firmware version 'v5.6.5 Cybertan Divo 090221 14:43:44' from 'NVMEM'
[ 16.059953] aquantia_phy_api_ops_init[1485]:INFO:qca probe aquantia phy driver succeeded!
[ 17.930149] Aquantia AQR114C 90000.mdio-1:08: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:08, irq=POLL)
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>
Changes:
- Support of both Apple Silicon and Intel for macOS package.
- Add cvlan/svlan/tpmr capabilities.
- Disable LLDP in firmware for Intel X7xx cards on FreeBSD.
- Add lldpctl_watch_sync_unblock to liblldpctl.
- Add C++ wrapper for lldpctl.
Fix:
- Fix AppArmor policy for /run/lldpd/lldpd.socket.lock.
- Do not query stats for a down interface on Linux.
```
# lldpd -vv
lldpd 1.0.19
Built on 2025-03-24T17:43:44Z
Additional LLDP features: LLDP-MED, Dot1, Dot3, Custom TLV
Additional protocols: CDP, FDP, EDP, SONMP
SNMP support: no
Old kernel support: no (Linux 2.6.39+)
Privilege separation: enabled
Privilege separation user: lldp
Privilege separation group: lldp
Privilege separation chroot: /var/run/lldp
Configuration directory: /tmp
C compiler command: C compiler command is not available for reproducible builds
Linker command: Linker compiler command is not available for reproducible builds
```
Tested on: 24.10.0
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18345
Signed-off-by: Nick Hainke <vincent@systemli.org>
With this patch, iw can now scan APs in the 6 GHz band and shows
their operation parameters:
~~~
6 Ghz Operation Information: 0x0103070f06
Primary Channel: 1
Channel Width: 80+80 or 160 MHz
Regulatory Info: 0
Center Frequency Segment 0: 7
Center Frequency Segment 1: 15
Minimum Rate: 6
~~~
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/18240
Signed-off-by: Robert Marko <robimarko@gmail.com>
ChangeLog
417c2e3 libtracefs: version 1.8.1
41efd9e libtracefs: Add meson build targets to Makefile
310b796 libtracefs utest: Add better logic to cause missed events
b589e32 libtracefs: Add cpu-map sample to trace mapped buffer
4ede86e libtracefs: Enable mmapped ring buffer
e6737d4 libtracefs: Initialize val in build_filter()
590e452 libtracefs: Close dir in the error path in tracefs_event_systems()
0309a87 libtracefs: Close dir in the error path in tracefs_system_events()
f34fb1f libtracefs: Prevent memory leak in tracefs_dynevent_get_all()
48e906b libtracefs: my_yyinput() should return 0 when no data can be read
5e5b2a7 libtracefs: Prevent memory leak in tracefs_instance_create()
8f2593f libtracefs: Prevent a memory leak in open_cpu_files()
7d77b83 libtracefs: Prevent a memory leak in tracefs_system_events()
7fcd8d2 libtracefs: Prevent a memory leak in add_func_str()
a01d0ba libtracefs: Don't leak socket file descriptor in open_vsock()
efdf7f7 libtracefs: Prevent memory leak in tracefs_event_systems()
2342293 libtracefs: Prevent a memory leak in tracefs_synth_add_end_field()
1c95394 libtracefs: Prevent a memory leak in update_fields()
6b35665 libtracefs: Prevent memory leak in append_filer()
aecc0b7 libtracefs: Call va_end() before exiting tracefs_hist_set_sort_key()
a5e37f7 libtracefs: Add trace-mmap.c to meson build
8f62e96 libtracefs meson: Use SemVer in the build description
e04fa01 meson: Add utest option
fb213a4 libtracefs: Update trace_buffer_meta
04505a0 libtracefs utest: Include libgen.h for basename()
7b4a9c9 libtracefs utest: Define _LARGEFILE64_SOURCE for lseek64() with musl
ba75081 libtracefs utest: Add PATH_MAX if it is not already defined
5f27b7f libtracefs: Update the kbuf for previous read in trace_mmap_load_subbuf()
73ac9c1 libtracefs: Fix tracefs_instance_reset() of triggers
7d15d77 libtracefs meson: build tracefs-mmap by default
Link: https://github.com/openwrt/openwrt/pull/18349
Signed-off-by: Nick Hainke <vincent@systemli.org>
ChangeLog:
bd47bd5 libtraceevent: 1.8.4
fe0bc49 libtraceevent: Print function pointer address when TEP_EVENT_FL_PRINTRAW is specified
f2224d5 libtraceevent: Have sizeof() parsing handle u8/s8 through u64/s64
5f570de libtraceevent: Print arrays like Linux does
645a883 libtraceevent: 1.8.3
d4c1fb4 libtraceevent: Add meson build targets to Makefile
c3dc220 libtraceevent: Fix a double free in process_op()
021da90 libtraceevent: Do not return a local stack pointer in get_field_str()
340e2e6 libtraceevent: Have unit test fail when any tests fail
c84155f libtraceevent: prevent a memory leak in tep_plugin_add_option()
03551eb libtraceevent: Prevent a memory leak in process_fields()
34ece90 libtraceevent: Close shared object in the error path of load_plugin()
8802f0f libtraceevent: Avoid a simple asprintf case
76a0eb8 libtraceevent: Fix event-parse memory leak in process_cond
5bc98bd libtraceevent: Have single quotes represent characters
ec8e0cc libtraceevent: Fix tests running on big endian arch
60ed6c3 libtraceevent: build: Various fixes for the Meson build of libtraceevent
0351241 libtraceevent utest: Include libgen.h for basename() with musl
Link: https://github.com/openwrt/openwrt/pull/18349
Signed-off-by: Nick Hainke <vincent@systemli.org>
Currently, both envtools and the rest of U-Boot tools are being built
regardless if the dumpimage package has been selected.
This will fail if only envtools are selected since the rest of tools
require OpenSSL while envtools do not require them.
So, only build tools if dumpimage is selected.
Fixes: 46e376c935 ("uboot-tools: migrate uboot-envtools to uboot-tools")
Fixes: #18327
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/18329
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
SoC: Qualcomm IPQ6000
RAM: 512 MiB
Flash: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: 2.4GHz 802.11b/g/n/ax 2x2
WLAN2: 5GHz 802.11a/n/ac/ax 2x2
Button: Reset, Switch
USB: 1x 3.0
SD slot: 1 in GL-AXT1800
Install via stock firmware:
Upload factory.bin in stock firmware's upgrade page,
do not preserve settings.
Install via uboot web failsafe:
Push the reset button for 5 seconds, then use broswer
to access http://192.168.1.1, and upload factory.ubi.
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Do not verify the format of TLV. Leave that to lldpd.
These lldpd config entries:
config custom-tlv
list ports 'eth0'
option tlv 'replace oui 33,44,55 subtype 254 oui-info 55,55,55,55,55'
config custom-tlv
option tlv 'oui 33,44,44 subtype 232'
list ports 'br-lan'
list ports 'eth0'
config custom-tlv # oui-info truncated
option tlv 'add oui 33,44,33 subtype 66 oui-info 5555555555'
config custom-tlv
option tlv 'add oui 33,44,31 subtype 44'
config custom-tlv # invalid oui
option tlv 'add oui 3322 subtype 79'
config custom-tlv # invalid oui
option tlv 'oui 3312 subtype 74'
Produce the following lldpd.conf content:
configure ports eth0 lldp custom-tlv replace oui 33,44,55 subtype 254 oui-info 55,55,55,55,55
configure ports br-lan,eth0 lldp custom-tlv oui 33,44,44 subtype 232
configure lldp custom-tlv add oui 33,44,33 subtype 66 oui-info 5555555555
configure lldp custom-tlv add oui 33,44,31 subtype 44
configure lldp custom-tlv add oui 3322 subtype 79
configure lldp custom-tlv oui 3312 subtype 74
And lldpd (v1.0.13 on v22) logs the following:
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op replace oui 33:44:55 subtype fe
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:44 subtype e8
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:33 subtype 42
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:33 subtype 42
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:31 subtype 2c
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:31 subtype 2c
Sat Mar 16 19:11:39 2024 daemon.warn lldpcli[10915]: invalid OUI value '3322'
Sat Mar 16 19:11:39 2024 daemon.info lldpcli[10915]: an error occurred while executing last command
Sat Mar 16 19:11:39 2024 daemon.warn lldpcli[10915]: invalid OUI value '3312'
Sat Mar 16 19:11:39 2024 daemon.info lldpcli[10915]: an error occurred while executing last command
Sat Mar 16 19:11:39 2024 daemon.info lldpcli[10915]: lldpd should resume operations
( The last two TLV are invalid: their oui must be three hex bytes, comma
separated. Only the first hex byte of oui-info 5555555555 is used )
Depends on #14867 and its release version bump
Tested on: 22.03.6
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14872
Signed-off-by: Robert Marko <robimarko@gmail.com>
where csv = comma separated value(s)
Make the function more generic. Can use it for not only 'config'.
Now it can be used to parse interfaces for additional lldpd settings,
e.g. custom-tlv.
Tested on: 22.03.6
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14872
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add uboot-tools stub package skeleton which will replace uboot-envtools
and also provide target-builds for other U-Boot tools.
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
As described in #13873, from 23.05.0 onwards logging to a file on an
external filesystem fails under some conditions.
This occurs because the log initscript had code added to prevent start
logging to an external filesystem on boot, and added a trigger to start
said logging when the external filesystem gets mounted.
The issue is that for filesystems mount with fstab uci, the fstab
scripts runs at START=11, while log runs at START=12, which means the
external filesystem may already be mounted by the time the log initscript
runs. Since the external filesystem is already mounted it does not
trigger a hotplug event to trigger the trigger to start logging. This
combination means the logging never automatically starts when the log
file is on an external filesystem.
We therefore add a check for the presence of a mounted filesystem when
the log file is being sent to an fstab mounted filesystem. If the
filesystem is mounted, we don't skip starting logging during boot.
If the filesystem is not mounted then file logging is not started and
the trigger will start the logging when the filesystem is mounted.
Signed-off-by: Daniel F. Dickinson <dfdpublic@wildtechgarden.ca>
[improved commit message]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
PKG_MIRROR_HASH is incorrect and the package check is currently failing.
Fixes: 4990ce613b ("ipq-wifi: update to 2024-02-17")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add support for the Intel E800 series of cards, with switchdev
support enabled for lower CPU usage.
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
Link: https://github.com/openwrt/openwrt/pull/17564
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This service automatically establishes connections to any hosts that are members
of the same unet network, and allows publish/subscribe exchanges via ubus channels.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is useful for keeping specific data on a device across factory reset.
It uses a separate partition (only UBI supported at the moment) to store
the data. The primary use case is storing sensitive data like cryptographic
keys for maintaining a device as part of a network.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This does not actually create a new private key. Instead, the salt is replaced,
and a xor key is generated which when merged with the key derived from the new
password transforms into the original private key.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
