Commit ab805ec316 ("generic: add missing squashfs config") enabled
CONFIG_SQUASHFS_DECOMP_MULTI_PERCPU in the generic config, so it is no
longer needed in the target configs.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Link: https://github.com/openwrt/openwrt/pull/21465
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace pending patches which are already integrated in upstream Linux
with their upstream versions.
These patches were exported with:
git format-patch -1 -k
Link: https://github.com/openwrt/openwrt/pull/21366
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On the smartrg sr505n the bootloader only sets registers to enable the
PHYs if it's interrupted. When Linux boots this results in a -EINVAL
error when trying to read from the EPHYs and the GPHY doesn't work.
This patch disables low power mode in the GPHY/EPHYs and properly resets
the EPHYs.
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17648
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The ralink custom property is deprecated and only kept around for
byteswap capability.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21058
Signed-off-by: Robert Marko <robimarko@gmail.com>
Avoids having to create a custom LED for wifi.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21058
Signed-off-by: Robert Marko <robimarko@gmail.com>
The child node "partitions" doesn't have "reg" property. Hence, we
don't need to use "#address-cells" and "#size-cells" to describe the
reg property information.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20942
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
These patches fix the remaining issues with BCM5325 switches and allow
dropping the default VLAN on Huawei HG556a.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
These patches have been accepted for linux v6.18.
e57723fe536f net: dsa: b53: properly bound ARL searches for < 4 ARL bin chips
674b34c4c770 net: dsa: b53: fix ageing time for BCM53101
89eb9a62aed7 net: dsa: b53: fix reserved register access in b53_fdb_dump()
61730ac10ba9 net: dsa: b53: mmap: Implement bcm63268 gphy power control
7f95f04fe190 net: dsa: b53: mmap: Add gphy port to phy info for bcm63268
5ac00023852d net: dsa: b53: mmap: Implement bcm63xx ephy power control
e8e13073dff7 net: dsa: b53: mmap: Add register layout for bcm6368
c251304ab021 net: dsa: b53: mmap: Add register layout for bcm6318
aed2aaa3c963 net: dsa: b53: mmap: Add syscon reference and register layout for bcm63268
fcf02a462fab net: dsa: b53: Define chip IDs for more bcm63xx SoCs
be7a79145d85 net: dsa: b53: Add phy_enable(), phy_disable() methods
762e7e174da9 net: dsa: tag_brcm: do not mark link local traffic as offloaded
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
gpio-leds were not working on F@ST3864OP before was merged.
This pull request adds definitions for all LEDs, including the previously
non-working WAN LEDs.
Signed-off-by: Hang Zhou <929513338@qq.com>
Link: https://github.com/openwrt/openwrt/pull/20533
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
- Add the missing ranges property for PCIe bridge node.
- Correct the PCIe device node name.
This patch fix the following dtc warning:
../dts/bcm6328-dlink-dsl-2750b-b1.dts:203.9-220.4: Warning (pci_bridge): /ubus/pcie@10e40000/pcie@0: missing ranges for PCI bridge (or not a bridge)
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18242
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
of_gpio.h is deprecated in upstream Linux and may be removed soon. Get
ahead of things and remove it. Most of these drivers already use the
gpiod API.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20076
Signed-off-by: Robert Marko <robimarko@gmail.com>
Directly call the function "get_linux_version()" to get the integer
kernel version number.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport accepted BCM5325 patches from net-next.
These patches will be merged in the v6.17 kernel window.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Specifications:
- SoC: Broadcom BCM6358 dual 300MHz MIPS
- Flash: 16MB NOR
- RAM: 64MB DDR
- Ethernet: 4x 100M
- Wifi: Broadcom BCM4318
- 2x USB 2.0 port
- 2x Button
- 9x LED
- RJ11 2x FXS VoIP (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
- Assign static IP 192.168.1.100 to PC.
- Unplug the power source.
- Press the RESTART button at the router, don't release it yet!
- Plug the power source and wait at least 15 seconds.
- Release the RESTART button.
- Browse to http://192.168.1.1 with your PC.
- Upload the openwrt-bmips-bcm6358-huawei_hg553-squashfs-cfe.bin file.
- Wait some minutes until the firmware upgrade completes.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Specifications:
- SoC: Broadcom BCM6358 dual 300MHz MIPS
- Flash: 16MB NOR Macronix MX29GL128EHT2I-90G
- RAM: 64MB DDR
- Ethernet: 4x 100M
- Wifi: Ralink RT3062F
- 3x USB 2.0 port
- 4x Button
- 13x LED
- RJ11 2x FXS VoIP (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
- Assign static IP 192.168.1.100 to PC.
- Unplug the power source.
- Press the RESTART button at the router, don't release it yet!
- Plug the power source and wait at least 15 seconds.
- Release the RESTART button.
- Browse to http://192.168.1.1 with your PC.
- Upload the openwrt-bmips-bcm6358-huawei_hg556a-c-squashfs-cfe.bin file.
- Wait some minutes until the firmware upgrade completes.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Specifications:
- SoC: Broadcom BCM6358 dual 300MHz MIPS
- Flash: 16MB NOR Spansion S29GL128P10
- RAM: 64MB DDR
- Ethernet: 4x 100M
- Wifi: Atheros AR9223
- 3x USB 2.0 port
- 4x Button
- 13x LED
- RJ11 2x FXS VoIP (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
- Assign static IP 192.168.1.100 to PC.
- Unplug the power source.
- Press the RESTART button at the router, don't release it yet!
- Plug the power source and wait at least 15 seconds.
- Release the RESTART button.
- Browse to http://192.168.1.1 with your PC.
- Upload the openwrt-bmips-bcm6358-huawei_hg556a-a-squashfs-cfe.bin file.
- Wait some minutes until the firmware upgrade completes.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Commit Fixes: 15430a1348 ("bmips: use wan ports as standalone ports")
removed bridge devices and therefore switch.1 no longer exists, so let's
use br-lan instead.
Fixes: 15430a1348 ("bmips: use wan ports as standalone ports")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
With the recent fixes backported to 6.12, b53 ports should now fully
work as standalone ports outside of a switch.
So move them out of the switch and use them as standalone ports, which
makes configuring easier as VLANs don't need to be defined and reserved
anymore to use the wan port.
Tested on DGND3700v1.
While most devices do not define a wan port, I dropped the
ucidef_set_bridge_device() from all devices for consistency.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The external switch of the Huawei HG556a is a BCM5325E connected by MDIO.
All the DSA brcm legacy FCS tag and b53 patches have been submitted upstream
and will be backported when accepted.
There are still some sporadic FDB errors, but at least the switch is working
and stable on my device:
bcm53xx fffe4800.ethernet-mii:1e: port 0 failed to add 72:31:59:xx:xx:xx vid 1 to fdb: -28
bcm53xx fffe4800.ethernet-mii:1e: port 0 failed to add 5c:4c:a9:xx:xx:xx vid 0 to fdb: -28
bcm53xx fffe4800.ethernet-mii:1e: port 0 failed to add 5c:4c:a9:xx:xx:xx vid 1 to fdb: -28
bcm53xx fffe4800.ethernet-mii:1e: port 0 failed to delete 72:31:59:xx:xx:xx vid 1 from fdb: -2
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
- Update subtarget configs for kernel 6.12.
- Refresh patches for kernel 6.12.
- Drop 210-revert-macronix-nand-block-protection.patch since brcmnand no longer
implements low level ops.
- Adapt bcm63268 gpio switches for 6.12 numbering.
- Add b53 pending patches from Jonas Gorski to fix system hangs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This is an automatically generated commit which aids following kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
bcm6328, bcm6362 and bcm6368 targets are missing a key config symbol which
prevents the NAND from working.
Fixes: f6c02b014d ("bmips: 6.1: refresh config and add missing symbols")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
There's no need for it. Kernel update to 6.12 found that it now needs
linux/of.h explicitly included.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18763
Signed-off-by: Robert Marko <robimarko@gmail.com>
Include <linux/of.h> instead of <linux/of_device.h>.
This problem arised when adding support for 6.12, but it can be fixed on
older kernels too.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This problem arised when adding support for 6.12, but it should be fixed on
older kernels too.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
These drivers should include <linux/platform_device.h>, but this wasn't an
issue on kernels < 6.12.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Currently, bcm63xx-cfe is being installed into kernel build dir, however
that does not work for Image Builder as only certain artifacts from kernel
build dir are included in Image Builder.
So, simply install bcm63xx-cfe into image staging dir so its artifacts can
be used in Image Builder as well.
Fixes: #18408Fixes: #18409
Link: https://github.com/openwrt/openwrt/pull/18463
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
- SoC: Broadcom BCM63168 dual 400MHz MIPS
- Flash: 128MB NAND ESMT F59L1G81A
- RAM: 128MB DDR3
- Ethernet: 5x 1000M
- Wifi: BCM435F
- 1x USB 2.0 port
- 2x Button
- 11x LED
- Coax HPNA (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
The booloader will only install signed firmware so the image has to
be manually flashed.
- Set up a TFTP server on 192.168.1.0/24 to serve the initramfs image
- Interrupt the bootloader and run from RAM with
r 192.168.1.100:openwrt-bmips-bcm63268-actiontec_t1200h-initramfs.elf
- On the openwrt console, copy the wfi image using wget/tftp/scp, i.e
scp user@192.168.1.100:~/openwrt/bin/targets/bmips/bcm63268/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin /tmp/
- Erase half the flash partition where openwrt will be installed with
flash_erase -j /dev/mtd1 0 491
- Flash the openwrt image with
nandwrite -p /dev/mtd1 /tmp/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin
- Reboot
- Interrupt the bootloader again and use the c command to boot from
previous firmware if vendor image is loaded
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[Minor improvements to DTS file]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The CONFIG_NET_SWITCHDEV option is needed by CONFIG_DSA and some other
options. It is boolean, we have to compile it into the kernel it self.
Activate it for all targets in the generic configuration, it is already
activated for most of them. This allows to install DSA drivers as a
module.
On the ramips/mt7620 target the kernel would grown by 4.5kB.
For some small targets which do not support a DSA switch by default the
option is deactivated.
Link: https://github.com/openwrt/openwrt/pull/17668
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch is also needed on bmips since it fixes issues with GPIOs not being
properly configured due to gpio_request_enable not being called on bcm63xx
devices. Therefore we can now drop the bcm63268 gpio function patch.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This LED controller has a driver under development which is currently being reviewed by the respective kernel maintainers. They are currently on v11 which is included here.
The LED1202 is a 12-channel low quiescent current LED driver with:
* Supply range from 2.6 V to 5 V
* 20 mA current capability per channel
* 1.8 V compatible I2C control interface
* 8-bit analog dimming individual control
* 12-bit local PWM resolution
* 8 programmable patterns
If the led node is present in the controller then the channel is
set to active.
The output current can be adjusted separately for each channel by 8-bit
analog (current sink input) and 12-bit digital (PWM) dimming control. The
LED1202 implements 12 low-side current generators with independent dimming
control.
Internal volatile memory allows the user to store up to 8 different patterns,
each pattern is a particular output configuration in terms of PWM
duty-cycle (on 4096 steps). Analog dimming (on 256 steps) is per channel but
common to all patterns. Each device tree LED node will have a corresponding
entry in /sys/class/leds with the label name. The brightness property
corresponds to the per channel analog dimming, while the patterns[1-8] to the
PWM dimming control.
Signed-off-by: Manuel Fombuena <fombuena@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17451
Signed-off-by: Robert Marko <robimarko@gmail.com>
Right now there's no way to know what state CFE will leave the pinctrl
registers in, so they should be explicitly set by linux on boot. This
patch adds a gpio configuration for drivers that need it, i.e. gpio-leds.
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[improve patch and fix warnings]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
