mvebu: add support for Turris MOX

Adds support for Turris MOX, a modular router extendable by board modules (MOX B-G).

You can explore the idea behind the modules at: https://mox-configurator.turris.cz/

More information about Turris MOX can be found here: https://docs.turris.cz/hw/mox/intro/

Also works with Turris Shield (Turris MOX A and C with a simplified OS UI).

Specifications:
-----------------------

MOX A
- SoC: Marvell Armada 3720
- RAM: 512/1024 MB, DDR3
- Memory:
    - 8 MB SPI NOR Flash for U-Boot and rescue system
    - SD card slot
- 1x RJ-45, 1Gbps
- 1x USB 3.0
- 1x activity LED
- 1x reset button
- SDIO header
- misc pin header (UART, GPIO, JTAG, ...)

MOX B, G
- 1x mPCIe slot
- 1x SIM slot

MOX C
- 4x RJ-45, 1Gbps

MOX D
- SFP, 2.5Gbps

MOX E
- 8x RJ-45, 1Gbps

MOX F
- 4x USB 3.0

Module support:
-----------------------

Additional packages are needed for some modules.

MOX A (core)
- works as is

MOX B, G (mPCIe, mPCIe passthrough)
- works as is

MOX C, E (4x, 8x RJ-45)
- kmod-dsa
- kmod-dsa-mv88e6xxx

MOX D (SFP)
- kmod-sfp
- kmod-phy-marvell-10g

MOX F (4x USB 3.0)
- works as is

Wi-Fi 5, 3x3 card (WLE900VX)
- kmod-ath10k
- ath10k-board-qca988x
- ath10k-firmware-qca988x

Wi-Fi 6, DBDC, 2x2 card (MT7915DAN)
- kmod-mt7915e
- kmod-mt7915-firmware

Interface naming:
-----------------------

- MOX A's RJ-45 is assigned to `eth0`.
- MOX C, E (4x, 8x RJ-45) are assigned to `lan<number>@eth1`
- If MOX D (SFP) is connected directly to MOX A, the resulting interface
  is `eth1`. If it's connected through MOX E (8x RJ-45), the resulting
  interface is `sfp@eth1`.

Quirks:
-----------------------

- MOX is sensitive to the order of connected modules. Verify that the
  confguration is valid at: https://mox-configurator.turris.cz/
- `CONFIG_MOXTET` and `CONFIG_GPIO_MOXTET` need to be enabled in kernel
  config. Moxtet is a bus protocol needed to discover and configure MOX
  modules. It must be compiled into the kernel for the modules to work.
  Though it's very small so it won't bloat up the kernel image.

Flashing instructions:
-----------------------

1. Download `openwrt-*-ext4-sdcard.img.gz` and `gunzip` it.
2. Insert an SD card and flash the image to it using dd:
   dd if=openwrt-*-ext4-sdcard.img.gz of=/dev/mmcblk0 bs=4096 conv=fsync
3. Plug the SD card into MOX.

Troubleshooting:
-----------------------

- https://docs.turris.cz/hw/serial/#turris-mox
- https://docs.turris.cz/hw/mox/rescue-modes/

Signed-off-by: Tomáš Macholda <tomas.macholda@nic.cz>
Link: https://github.com/openwrt/openwrt/pull/20356
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

package/boot/uboot-mvebu/Makefile

@@ -22,6 +22,13 @@ define U-Boot/Default
   HIDDEN:=1
 endef
 
+define U-Boot/mox
+  NAME:=CZ.NIC Turris Mox
+  BUILD_DEVICES:=cznic_turris-mox
+  BUILD_SUBTARGET:=cortexa53
+  UBOOT_CONFIG:=turris_mox
+endef
+
 define U-Boot/clearfog
   NAME:=SolidRun ClearFog A1
   BUILD_DEVICES:=solidrun_clearfog-base-a1 solidrun_clearfog-pro-a1
@@ -69,6 +76,7 @@ define U-Boot/rb5009
 endef
 
 UBOOT_TARGETS:= \
+	mox \
 	clearfog \
 	helios4 \
 	omnia \

target/linux/mvebu/cortexa53/base-files/etc/board.d/01_leds

@@ -7,6 +7,9 @@ board_config_update
 board=$(board_name)
 
 case "$board" in
+cznic,turris-mox)
+        ucidef_set_led_heartbeat "wan" "MOX A" "mox:red:activity"
+        ;;
 glinet,gl-mv1000)
 	ucidef_set_led_netdev "wan" "WAN" "green:wan" "wan"
 	;;

target/linux/mvebu/cortexa53/base-files/etc/board.d/02_network

@@ -10,6 +10,18 @@ board_config_update
 board=$(board_name)
 
 case "$board" in
+cznic,turris-mox)
+	mox_lan_interfaces=""
+	for net in /sys/class/net/lan*; do
+		[ -e "$net" ] || continue
+		append mox_lan_interfaces "${net##*/}"
+	done
+	if [ -z "$mox_lan_interfaces" ]; then
+		ucidef_set_interface_lan "eth0"
+	else
+		ucidef_set_interfaces_lan_wan "$mox_lan_interfaces" "eth0"
+	fi
+	;;
 glinet,gl-mv1000|\
 globalscale,espressobin|\
 globalscale,espressobin-emmc|\

target/linux/mvebu/cortexa53/config-6.12

@@ -54,12 +54,14 @@ CONFIG_GENERIC_BUG_RELATIVE_POINTERS=y
 CONFIG_GENERIC_CSUM=y
 CONFIG_GENERIC_IOREMAP=y
 CONFIG_GENERIC_PINCONF=y
+CONFIG_GPIO_MOXTET=y
 CONFIG_ILLEGAL_POINTER_VALUE=0xdead000000000000
 CONFIG_MAILBOX=y
 # CONFIG_MAILBOX_TEST is not set
 CONFIG_MFD_SYSCON=y
 CONFIG_MMC_SDHCI_XENON=y
 CONFIG_MODULES_USE_ELF_RELA=y
+CONFIG_MOXTET=y
 CONFIG_MVEBU_GICP=y
 CONFIG_MVEBU_ICU=y
 CONFIG_MVEBU_ODMI=y

target/linux/mvebu/image/cortexa53.mk

@@ -1,3 +1,13 @@
+define Device/cznic_turris-mox
+  $(call Device/Default-arm64)
+  DEVICE_VENDOR := CZ.NIC
+  DEVICE_MODEL := Turris MOX
+  DEVICE_PACKAGES := kmod-usb2 kmod-gpio-button-hotplug kmod-rtc-ds1307 kmod-i2c-pxa
+  SOC := armada-3720
+  BOOT_SCRIPT := turris-mox
+endef
+TARGET_DEVICES += cznic_turris-mox
+
 define Device/glinet_gl-mv1000
   $(call Device/Default-arm64)
   DEVICE_VENDOR := GL.iNet

target/linux/mvebu/image/turris-mox.bootscript

@@ -0,0 +1,50 @@
+if part uuid ${devtype} ${devnum}:${distro_bootpart} bootuuid; then
+	if test "${bootfstype}" = "btrfs"; then
+		# Original BTRFS partition layout
+		rootdev="PARTUUID=${bootuuid}"
+		rootflags="commit=5,subvol=@"
+		bootpath="/@/boot"
+	else
+		# OpenWrt default ext4 bootpart + rootpart layout
+		rootdev="/dev/mmcblk0p2"
+		rootflags="commit=5"
+		bootpath="/"
+	fi
+
+	load ${devtype} ${devnum}:${distro_bootpart} ${fdt_addr_r} ${bootpath}/armada-3720-turris-mox.dtb
+	if test "$filesize" != "0"; then
+		has_dtb=1
+	else
+		setenv has_dtb 0
+		echo "Cannot find device tree binary!"
+	fi
+
+	if test $has_dtb -eq 1; then
+		load ${devtype} ${devnum}:${distro_bootpart} ${kernel_addr_r} ${bootpath}/Image
+		if test "$filesize" = "0"; then
+			echo "Failed to load ${bootpath}/Image"
+			echo "Now trying ${bootpath}/Image.lzma"
+			tmp_addr_r=0x10000000
+			load ${devtype} ${devnum}:${distro_bootpart} ${tmp_addr_r} ${bootpath}/Image.lzma
+			if test "$filesize" != "0"; then
+				if lzmadec ${tmp_addr_r} ${kernel_addr_r}; then
+					echo "Successfully decompressed Image.lzma"
+				else
+					echo "Failed decompressing Image.lzma"
+					filesize=0
+				fi
+			else
+				echo "Failed to load ${subvol}/boot/Image.lzma"
+			fi
+		fi
+		if test "$filesize" != "0"; then
+			setenv bootargs "earlyprintk console=ttyMV0,115200 earlycon=ar3700_uart,0xd0012000 rootfstype=${bootfstype} root=${rootdev} rootflags=${rootflags} rootwait ${contract} rw cfg80211.freg=${regdomain} ${quirks}"
+			booti ${kernel_addr_r} - ${fdt_addr_r}
+			echo "Booting Image failed"
+		else
+			echo "Cannot load kernel binary"
+		fi
+	fi
+
+	env delete bootuuid rootpart
+fi