mirror of
https://git.openwrt.org/openwrt/openwrt.git
synced 2026-01-28 03:37:17 +01:00
ipq40xx: add support for Netgear RBS20
This device has only half the flash and ram of the RBR20. It also has
two lan ports instead of wan and lan.
Hardware
--------
SOC: Qualcomm IPQ4019
FLASH: 128MB (Winbond W29N01HVSINF)
RAM: 256MB (Winbond W632GU6MB-12)
WIFI: Qualcomm IPQ4019
Qualcomm Atheros QCA9886
ETH: 2x LAN
LED: 5 (4 RGB at top, 1 RG at back)
BTN: WPS, Reset
UART: 115200 8N1 (dotted Pin = VCC) VCC-TX-RX-GND
MAC addresses
-------------
LAN Label MAC (stored in boarddata1 offset 0x0)
2.4G LAN
5GLow LAN + 3 (stored in boarddata1 offset 0xc)
5GUpper LAN + 2 (stored in boarddata1 offset 0x12)
Installation
------------
Either use the vendor ui upgrade method or nmrpflash to install the
factory image.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20560
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit is contained in:
Christoph Krapp
Robert Marko
parent
251d551fa6
commit
0db1b11073
7 changed files with 502 additions and 272 deletions
|
|
@ -55,7 +55,8 @@ aruba,ap-365)
|
|||
;;
|
||||
buffalo,wtr-m2133hp|\
|
||||
netgear,lbr20|\
|
||||
netgear,rbr20)
|
||||
netgear,rbr20|\
|
||||
netgear,rbs20)
|
||||
ubootenv_add_uci_config "/dev/mtd8" "0x0" "0x40000" "0x20000"
|
||||
;;
|
||||
linksys,ea6350v3)
|
||||
|
|
|
|||
|
|
@ -81,7 +81,8 @@ ipq40xx_setup_interfaces()
|
|||
;;
|
||||
avm,fritzrepeater-3000|\
|
||||
cellc,rtl30vw|\
|
||||
compex,wpj428)
|
||||
compex,wpj428|\
|
||||
netgear,rbs20)
|
||||
ucidef_set_interface_lan "lan1 lan2"
|
||||
;;
|
||||
devolo,magic-2-wifi-next)
|
||||
|
|
|
|||
|
|
@ -124,6 +124,7 @@ platform_do_upgrade() {
|
|||
mobipromo,cm520-79f|\
|
||||
netgear,lbr20|\
|
||||
netgear,rbr20|\
|
||||
netgear,rbs20|\
|
||||
netgear,wac510|\
|
||||
p2w,r619ac-64m|\
|
||||
p2w,r619ac-128m|\
|
||||
|
|
|
|||
|
|
@ -1,178 +1,10 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
#include "qcom-ipq4019-rbx20.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Netgear RBR20";
|
||||
compatible = "netgear,rbr20";
|
||||
|
||||
chosen {
|
||||
bootargs-append = "ubi.mtd=ubi root=/dev/ubiblock0_0";
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &led_status_white;
|
||||
led-failsafe = &led_status_red;
|
||||
led-running = &led_status_green;
|
||||
led-upgrade = &led_status_blue;
|
||||
label-mac-device = &gmac;
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led-0 {
|
||||
function = LED_FUNCTION_POWER;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&tlmm 22 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
led-1 {
|
||||
function = LED_FUNCTION_POWER;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
gpios = <&tlmm 23 GPIO_ACTIVE_HIGH>;
|
||||
panic-indicator;
|
||||
};
|
||||
|
||||
led_status_green: led-2 {
|
||||
function = LED_FUNCTION_STATUS;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&tlmm 24 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_status_red: led-3 {
|
||||
function = LED_FUNCTION_STATUS;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_status_blue: led-4 {
|
||||
function = LED_FUNCTION_STATUS;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_status_white: led-5 {
|
||||
function = LED_FUNCTION_STATUS;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
gpios = <&tlmm 27 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
soc {
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
status = "okay";
|
||||
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&prng {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
mdio_pins: mdio-pinmux {
|
||||
mux_mdio {
|
||||
pins = "gpio6";
|
||||
function = "mdio";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mux_mdc {
|
||||
pins = "gpio7";
|
||||
function = "mdc";
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
serial_pins: serial-pinmux {
|
||||
function = "blsp_uart0";
|
||||
pins = "gpio16", "gpio17";
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
nand_pins: nand-pins {
|
||||
pullups {
|
||||
pins = "gpio53", "gpio58", "gpio59";
|
||||
function = "qpic";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
pulldowns {
|
||||
pins = "gpio54", "gpio55", "gpio56",
|
||||
"gpio57", "gpio60", "gpio61",
|
||||
"gpio62", "gpio63", "gpio64",
|
||||
"gpio65", "gpio66", "gpio67",
|
||||
"gpio68", "gpio69";
|
||||
function = "qpic";
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&nand {
|
||||
|
|
@ -377,70 +209,6 @@
|
|||
};
|
||||
};
|
||||
|
||||
&blsp1_i2c3 {
|
||||
status = "okay";
|
||||
|
||||
led-controller@27 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
compatible = "ti,tlc59108"; /* really is tlc59208f */
|
||||
reg = <0x27>;
|
||||
|
||||
led0@0 {
|
||||
function = LED_FUNCTION_BACKLIGHT;
|
||||
function-enumerator = <0>;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
reg = <0x0>;
|
||||
linux,default-trigger = "default-on";
|
||||
};
|
||||
|
||||
led1@1 {
|
||||
function = LED_FUNCTION_BACKLIGHT;
|
||||
function-enumerator = <1>;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
reg = <0x1>;
|
||||
linux,default-trigger = "default-on";
|
||||
};
|
||||
|
||||
led2@2 {
|
||||
function = LED_FUNCTION_BACKLIGHT;
|
||||
function-enumerator = <2>;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
reg = <0x2>;
|
||||
linux,default-trigger = "default-on";
|
||||
};
|
||||
|
||||
led3@3 {
|
||||
function = LED_FUNCTION_BACKLIGHT;
|
||||
function-enumerator = <3>;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
reg = <0x3>;
|
||||
linux,default-trigger = "default-on";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&serial_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac {
|
||||
status = "okay";
|
||||
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&mac_address_lan 0>;
|
||||
};
|
||||
|
||||
&switch {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&swport4 {
|
||||
status = "okay";
|
||||
|
||||
|
|
@ -454,36 +222,3 @@
|
|||
|
||||
label = "lan";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
|
||||
perst-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
|
||||
wake-gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
&pcie_bridge0 {
|
||||
wifi@0,0 {
|
||||
compatible = "qcom,ath10k";
|
||||
reg = <0x00010000 0 0 0 0>;
|
||||
ieee80211-freq-limit = <5170000 5350000>;
|
||||
nvmem-cell-names = "pre-calibration", "mac-address";
|
||||
nvmem-cells = <&precal_art_9000>, <&mac_address_wlan_2nd5g 0>;
|
||||
qcom,ath10k-calibration-variant = "Netgear-RBK20";
|
||||
};
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
nvmem-cell-names = "pre-calibration", "mac-address";
|
||||
nvmem-cells = <&precal_art_1000>, <&mac_address_lan 0>;
|
||||
qcom,ath10k-calibration-variant = "Netgear-RBK20";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
ieee80211-freq-limit = <5470000 5815000>;
|
||||
nvmem-cell-names = "pre-calibration", "mac-address";
|
||||
nvmem-cells = <&precal_art_5000>, <&mac_address_wlan_5g 0>;
|
||||
qcom,ath10k-calibration-variant = "Netgear-RBK20";
|
||||
};
|
||||
|
|
|
|||
|
|
@ -0,0 +1,210 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcom-ipq4019-rbx20.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Netgear RBS20";
|
||||
compatible = "netgear,rbs20";
|
||||
};
|
||||
|
||||
&nand {
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
|
||||
nand@0 {
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "0:SBL1";
|
||||
reg = <0x00000000 0x00100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "0:MIBIB";
|
||||
reg = <0x00100000 0x00100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@200000 {
|
||||
label = "0:BOOTCONFIG";
|
||||
reg = <0x00200000 0x00100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@300000 {
|
||||
label = "0:QSEE";
|
||||
reg = <0x00300000 0x00100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@400000 {
|
||||
label = "0:QSEE_1";
|
||||
reg = <0x00400000 0x00100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@500000 {
|
||||
label = "0:CDT";
|
||||
reg = <0x00500000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@580000 {
|
||||
label = "0:CDT_1";
|
||||
reg = <0x00580000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@600000 {
|
||||
label = "0:BOOTCONFIG1";
|
||||
reg = <0x00600000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@680000 {
|
||||
label = "0:APPSBLENV";
|
||||
reg = <0x00680000 0x00080000>;
|
||||
};
|
||||
|
||||
partition@700000 {
|
||||
label = "0:APPSBL";
|
||||
reg = <0x00700000 0x00200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@900000 {
|
||||
label = "0:APPSBL_1";
|
||||
reg = <0x00900000 0x00200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@b00000 {
|
||||
label = "0:ART";
|
||||
reg = <0x00b00000 0x00080000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
precal_art_1000: precal@1000 {
|
||||
reg = <0x1000 0x2f20>;
|
||||
};
|
||||
|
||||
precal_art_5000: precal@5000 {
|
||||
reg = <0x5000 0x2f20>;
|
||||
};
|
||||
|
||||
precal_art_9000: precal@9000 {
|
||||
reg = <0x9000 0x2f20>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@b80000 {
|
||||
label = "0:ART.bak";
|
||||
reg = <0x00b80000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@c00000 {
|
||||
label = "config";
|
||||
reg = <0x00c00000 0x00100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@d00000 {
|
||||
label = "boarddata1";
|
||||
reg = <0x00d00000 0x00080000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
mac_address_lan: macaddr@0 {
|
||||
compatible = "mac-base";
|
||||
reg = <0x0 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
|
||||
mac_address_wlan_5g: macaddr@c {
|
||||
compatible = "mac-base";
|
||||
reg = <0xc 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
|
||||
mac_address_wlan_2nd5g: macaddr@12 {
|
||||
compatible = "mac-base";
|
||||
reg = <0x12 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@d80000 {
|
||||
label = "boarddata2";
|
||||
reg = <0x00d80000 0x00040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@dc0000 {
|
||||
label = "pot";
|
||||
reg = <0x00dc0000 0x00100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@ec0000 {
|
||||
label = "boarddata1.bak";
|
||||
reg = <0x00ec0000 0x00080000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@f40000 {
|
||||
label = "boarddata2.bak";
|
||||
reg = <0x00f40000 0x00040000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@f80000 {
|
||||
label = "language";
|
||||
reg = <0x00f80000 0x00300000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@1280000 {
|
||||
label = "ntgrdata";
|
||||
reg = <0x01280000 0x01e00000>;
|
||||
};
|
||||
|
||||
partition@3080000 {
|
||||
label = "kernel";
|
||||
reg = <0x03080000 0x00700000>;
|
||||
};
|
||||
|
||||
partition@3780000 {
|
||||
label = "ubi";
|
||||
reg = <0x03780000 0x04880000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&swport4 {
|
||||
status = "okay";
|
||||
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
&swport5 {
|
||||
status = "okay";
|
||||
|
||||
label = "lan2";
|
||||
};
|
||||
|
|
@ -0,0 +1,270 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
#include "qcom-ipq4019.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/soc/qcom,tcsr.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
chosen {
|
||||
bootargs-append = "ubi.mtd=ubi root=/dev/ubiblock0_0";
|
||||
};
|
||||
|
||||
aliases {
|
||||
led-boot = &led_status_white;
|
||||
led-failsafe = &led_status_red;
|
||||
led-running = &led_status_green;
|
||||
led-upgrade = &led_status_blue;
|
||||
label-mac-device = &gmac;
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led-0 {
|
||||
function = LED_FUNCTION_POWER;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&tlmm 22 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "on";
|
||||
};
|
||||
|
||||
led-1 {
|
||||
function = LED_FUNCTION_POWER;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
gpios = <&tlmm 23 GPIO_ACTIVE_HIGH>;
|
||||
panic-indicator;
|
||||
};
|
||||
|
||||
led_status_green: led-2 {
|
||||
function = LED_FUNCTION_STATUS;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&tlmm 24 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_status_red: led-3 {
|
||||
function = LED_FUNCTION_STATUS;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_status_blue: led-4 {
|
||||
function = LED_FUNCTION_STATUS;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led_status_white: led-5 {
|
||||
function = LED_FUNCTION_STATUS;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
gpios = <&tlmm 27 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
soc {
|
||||
tcsr@1949000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1949000 0x100>;
|
||||
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
||||
};
|
||||
|
||||
tcsr@194b000 {
|
||||
status = "okay";
|
||||
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x194b000 0x100>;
|
||||
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
||||
};
|
||||
|
||||
ess_tcsr@1953000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1953000 0x1000>;
|
||||
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
||||
};
|
||||
|
||||
tcsr@1957000 {
|
||||
compatible = "qcom,tcsr";
|
||||
reg = <0x1957000 0x100>;
|
||||
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&prng {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
mdio_pins: mdio-pinmux {
|
||||
mux_mdio {
|
||||
pins = "gpio6";
|
||||
function = "mdio";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mux_mdc {
|
||||
pins = "gpio7";
|
||||
function = "mdc";
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
serial_pins: serial-pinmux {
|
||||
function = "blsp_uart0";
|
||||
pins = "gpio16", "gpio17";
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
nand_pins: nand-pins {
|
||||
pullups {
|
||||
pins = "gpio53", "gpio58", "gpio59";
|
||||
function = "qpic";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
pulldowns {
|
||||
pins = "gpio54", "gpio55", "gpio56",
|
||||
"gpio57", "gpio60", "gpio61",
|
||||
"gpio62", "gpio63", "gpio64",
|
||||
"gpio65", "gpio66", "gpio67",
|
||||
"gpio68", "gpio69";
|
||||
function = "qpic";
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_i2c3 {
|
||||
status = "okay";
|
||||
|
||||
led-controller@27 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
compatible = "ti,tlc59108"; /* really is tlc59208f */
|
||||
reg = <0x27>;
|
||||
|
||||
led0@0 {
|
||||
function = LED_FUNCTION_BACKLIGHT;
|
||||
function-enumerator = <0>;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
reg = <0x0>;
|
||||
linux,default-trigger = "default-on";
|
||||
};
|
||||
|
||||
led1@1 {
|
||||
function = LED_FUNCTION_BACKLIGHT;
|
||||
function-enumerator = <1>;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
reg = <0x1>;
|
||||
linux,default-trigger = "default-on";
|
||||
};
|
||||
|
||||
led2@2 {
|
||||
function = LED_FUNCTION_BACKLIGHT;
|
||||
function-enumerator = <2>;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
reg = <0x2>;
|
||||
linux,default-trigger = "default-on";
|
||||
};
|
||||
|
||||
led3@3 {
|
||||
function = LED_FUNCTION_BACKLIGHT;
|
||||
function-enumerator = <3>;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
reg = <0x3>;
|
||||
linux,default-trigger = "default-on";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&serial_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac {
|
||||
status = "okay";
|
||||
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&mac_address_lan 0>;
|
||||
};
|
||||
|
||||
&switch {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
|
||||
perst-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
|
||||
wake-gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
&pcie_bridge0 {
|
||||
wifi@0,0 {
|
||||
compatible = "qcom,ath10k";
|
||||
reg = <0x00010000 0 0 0 0>;
|
||||
ieee80211-freq-limit = <5170000 5350000>;
|
||||
nvmem-cell-names = "pre-calibration", "mac-address";
|
||||
nvmem-cells = <&precal_art_9000>, <&mac_address_wlan_2nd5g 0>;
|
||||
qcom,ath10k-calibration-variant = "Netgear-RBK20";
|
||||
};
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
status = "okay";
|
||||
nvmem-cell-names = "pre-calibration", "mac-address";
|
||||
nvmem-cells = <&precal_art_1000>, <&mac_address_lan 0>;
|
||||
qcom,ath10k-calibration-variant = "Netgear-RBK20";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
status = "okay";
|
||||
ieee80211-freq-limit = <5470000 5815000>;
|
||||
nvmem-cell-names = "pre-calibration", "mac-address";
|
||||
nvmem-cells = <&precal_art_5000>, <&mac_address_wlan_5g 0>;
|
||||
qcom,ath10k-calibration-variant = "Netgear-RBK20";
|
||||
};
|
||||
|
|
@ -911,13 +911,10 @@ define Device/netgear_lbr20
|
|||
endef
|
||||
TARGET_DEVICES += netgear_lbr20
|
||||
|
||||
define Device/netgear_rbr20
|
||||
define Device/netgear_rbx20
|
||||
$(call Device/DniImage)
|
||||
SOC := qcom-ipq4019
|
||||
DEVICE_VENDOR := NETGEAR
|
||||
DEVICE_MODEL := RBR20
|
||||
NETGEAR_BOARD_ID := RBR20
|
||||
NETGEAR_HW_ID := 29765641+0+256+512+2x2+2x2+2x2
|
||||
KERNEL_SIZE := 7340032
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
|
|
@ -930,8 +927,23 @@ define Device/netgear_rbr20
|
|||
append-metadata
|
||||
DEVICE_PACKAGES := ipq-wifi-netgear_rbk20 ath10k-firmware-qca9888-ct
|
||||
endef
|
||||
|
||||
define Device/netgear_rbr20
|
||||
$(call Device/netgear_rbx20)
|
||||
DEVICE_MODEL := RBR20
|
||||
NETGEAR_BOARD_ID := RBR20
|
||||
NETGEAR_HW_ID := 29765641+0+256+512+2x2+2x2+2x2
|
||||
endef
|
||||
TARGET_DEVICES += netgear_rbr20
|
||||
|
||||
define Device/netgear_rbs20
|
||||
$(call Device/netgear_rbx20)
|
||||
DEVICE_MODEL := RBS20
|
||||
NETGEAR_BOARD_ID := RBS20
|
||||
NETGEAR_HW_ID := 29765641+0+128+512+2x2+2x2+2x2
|
||||
endef
|
||||
TARGET_DEVICES += netgear_rbs20
|
||||
|
||||
define Device/netgear_rbx40
|
||||
$(call Device/netgear_orbi)
|
||||
NETGEAR_HW_ID := 29765515+0+4096+512+2x2+2x2+2x2
|
||||
|
|
|
|||
Loading…
Add table
Reference in a new issue