forked from mirror/openwrt
1330816178
H3C TX180x series WiFi6 routers are customized by different carrier.
While these three devices look different, they use the same motherboard
inside. Another minor difference comes from the model name definition
in the u-boot environment variable.
Specifications:
SOC: MT7621 + MT7915
ROM: 128 MiB
RAM: 256 MiB
LED: status *2
Button: reset *1 + wps/mesh *1
Ethernet: lan *3 + wan *1 (10/100/1000Mbps)
TTL Baudrate: 115200
TFTP server IP: 192.168.124.99
MAC Address:
use address(sample 1) address(sample 2) source
label 88:xx:xx:98:xx:12 88:xx:xx:a2:xx:a5 u-boot-env@ethaddr
lan 88:xx:xx:98:xx:13 88:xx:xx:a2:xx:a6 $label +1
wan 88:xx:xx:98:xx:12 88:xx:xx:a2:xx:a5 $label
WiFi4_2G 8a:xx:xx:58:xx:14 8a:xx:xx:52:xx:a7 (Compatibility mode)
WiFi5_5G 8a:xx:xx:b8:xx:14 8a:xx:xx:b2:xx:a7 (Compatibility mode)
WiFi6_2G 8a:xx:xx:18:xx:14 8a:xx:xx:12:xx:a7
WiFi6_5G 8a:xx:xx:78:xx:14 8a:xx:xx:72:xx:a7
Compatibility mode is used to guarantee the connection of old devices
that only support WiFi4 or WiFi5.
TFTP + TTL Installation:
Although a TTL connection is required for installation, we do not need
to tear down it. We can find the TTL port from the cooling hole at the
bottom. It is located below LAN3 and the pins are defined as follows:
|LAN1|LAN2|LAN3|----|WAN|
--------------------
|GND|TX|RX|VCC|
1. Set tftp server IP to 192.168.124.99 and put initramfs firmware in
server's root directory, rename it to a simple name "initramfs.bin".
2. Plug in the power supply and wait for power on, connect the TTL cable
and open a TTL session, enter "reboot", then enter "Y" to confirm.
Finally push "0" to interruput boot while booting.
3. Execute command to install a initramfs system:
# tftp 0x80010000 192.168.124.99:initramfs.bin
# bootm 0x80010000
4. Backup nand flash by OpenWrt LuCI or dd instruction. We need those
partitions if we want to back to stock firmwre due to official
website does not provide download link.
# dd if=/dev/mtd1 of=/tmp/u-boot-env.bin
# dd if=/dev/mtd4 of=/tmp/firmware.bin
5. Edit u-boot env to ensure use default bootargs and first image slot:
# fw_setenv bootargs
# fw_setenv bootflag 0
6. Upgrade sysupgrade firmware.
7. About restore stock firmware: flash the "firmware" and "u-boot-env"
partitions that we backed up in step 4.
# mtd write /tmp/u-boot-env.bin u-boot-env
# mtd write /tmp/firmware.bin firmware
Additional Info:
The H3C stock firmware has a 160-byte firmware header that appears to
use a non-standard CRC32 verification algorithm. For this part of the
data, the u-boot does not check it so we can just directly replace it
with a placeholder.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
142 lines
3.2 KiB
Bash
Executable file
142 lines
3.2 KiB
Bash
Executable file
#
|
|
# Copyright (C) 2010 OpenWrt.org
|
|
#
|
|
|
|
PART_NAME=firmware
|
|
REQUIRE_IMAGE_METADATA=1
|
|
|
|
RAMFS_COPY_BIN='fw_printenv fw_setenv'
|
|
RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
|
|
|
|
platform_check_image() {
|
|
return 0
|
|
}
|
|
|
|
platform_do_upgrade() {
|
|
local board=$(board_name)
|
|
|
|
case "$board" in
|
|
alfa-network,quad-e4g)
|
|
[ "$(fw_printenv -n dual_image 2>/dev/null)" = "1" ] &&\
|
|
[ -n "$(find_mtd_part backup)" ] && {
|
|
PART_NAME=backup
|
|
if [ "$(fw_printenv -n bootactive 2>/dev/null)" = "1" ]; then
|
|
fw_setenv bootactive 2 || exit 1
|
|
else
|
|
fw_setenv bootactive 1 || exit 1
|
|
fi
|
|
}
|
|
;;
|
|
ampedwireless,ally-00x19k|\
|
|
ampedwireless,ally-r1900k)
|
|
if [ "$(fw_printenv --lock / -n bootImage 2>/dev/null)" != "0" ]; then
|
|
fw_setenv --lock / bootImage 0 || exit 1
|
|
fi
|
|
;;
|
|
mikrotik,routerboard-750gr3|\
|
|
mikrotik,routerboard-760igs|\
|
|
mikrotik,routerboard-m11g|\
|
|
mikrotik,routerboard-m33g)
|
|
[ "$(rootfs_type)" = "tmpfs" ] && mtd erase firmware
|
|
;;
|
|
asus,rt-ac65p|\
|
|
asus,rt-ac85p)
|
|
echo "Backing up firmware"
|
|
dd if=/dev/mtd4 bs=1024 count=4096 > /tmp/backup_firmware.bin
|
|
dd if=/dev/mtd5 bs=1024 count=52224 >> /tmp/backup_firmware.bin
|
|
mtd -e firmware2 write /tmp/backup_firmware.bin firmware2
|
|
;;
|
|
esac
|
|
|
|
case "$board" in
|
|
ampedwireless,ally-00x19k|\
|
|
ampedwireless,ally-r1900k|\
|
|
asus,rt-ac65p|\
|
|
asus,rt-ac85p|\
|
|
asus,rt-ax53u|\
|
|
beeline,smartbox-flash|\
|
|
beeline,smartbox-giga|\
|
|
dlink,dir-1960-a1|\
|
|
dlink,dir-2640-a1|\
|
|
dlink,dir-2660-a1|\
|
|
dlink,dir-853-a3|\
|
|
h3c,tx1800-plus|\
|
|
h3c,tx1801-plus|\
|
|
h3c,tx1806|\
|
|
hiwifi,hc5962|\
|
|
iptime,a3004t|\
|
|
iptime,ax2004m|\
|
|
iptime,t5004|\
|
|
jcg,q20|\
|
|
linksys,e5600|\
|
|
linksys,ea6350-v4|\
|
|
linksys,ea7300-v1|\
|
|
linksys,ea7300-v2|\
|
|
linksys,ea7500-v2|\
|
|
linksys,ea8100-v1|\
|
|
linksys,ea8100-v2|\
|
|
mts,wg430223|\
|
|
netgear,r6220|\
|
|
netgear,r6260|\
|
|
netgear,r6350|\
|
|
netgear,r6700-v2|\
|
|
netgear,r6800|\
|
|
netgear,r6850|\
|
|
netgear,r6900-v2|\
|
|
netgear,r7200|\
|
|
netgear,r7450|\
|
|
netgear,wac104|\
|
|
netgear,wac124|\
|
|
netgear,wax202|\
|
|
netis,wf2881|\
|
|
raisecom,msg1500-x-00|\
|
|
sercomm,na502|\
|
|
sercomm,na502s|\
|
|
xiaomi,mi-router-3g|\
|
|
xiaomi,mi-router-3-pro|\
|
|
xiaomi,mi-router-4|\
|
|
xiaomi,mi-router-ac2100|\
|
|
xiaomi,mi-router-cr6606|\
|
|
xiaomi,mi-router-cr6608|\
|
|
xiaomi,mi-router-cr6609|\
|
|
xiaomi,redmi-router-ac2100|\
|
|
zyxel,nwa50ax|\
|
|
zyxel,nwa55axe)
|
|
nand_do_upgrade "$1"
|
|
;;
|
|
iodata,wn-ax1167gr2|\
|
|
iodata,wn-ax2033gr|\
|
|
iodata,wn-dx1167r|\
|
|
iodata,wn-dx2033gr)
|
|
iodata_mstc_upgrade_prepare "0xfe75"
|
|
nand_do_upgrade "$1"
|
|
;;
|
|
iodata,wn-dx1200gr)
|
|
iodata_mstc_upgrade_prepare "0x1fe75"
|
|
nand_do_upgrade "$1"
|
|
;;
|
|
ubnt,edgerouter-x|\
|
|
ubnt,edgerouter-x-sfp)
|
|
platform_upgrade_ubnt_erx "$1"
|
|
;;
|
|
zyxel,nr7101)
|
|
fw_setenv CheckBypass 0
|
|
fw_setenv Image1Stable 0
|
|
[ "$(fw_printenv -n BootingFlag)" = "0" ] || fw_setenv BootingFlag 0
|
|
CI_KERNPART="Kernel"
|
|
nand_do_upgrade "$1"
|
|
;;
|
|
zyxel,wap6805)
|
|
local kernel2_mtd="$(find_mtd_part Kernel2)"
|
|
[ "$(hexdump -n 4 -e '"%x"' $kernel2_mtd)" = "56190527" ] &&\
|
|
[ "$(hexdump -n 4 -s 104 -e '"%x"' $kernel2_mtd)" != "0" ] &&\
|
|
dd bs=4 count=1 seek=26 conv=notrunc if=/dev/zero of=$kernel2_mtd 2>/dev/null &&\
|
|
echo "Kernel2 sequence number was reset to 0"
|
|
CI_KERNPART="Kernel"
|
|
nand_do_upgrade "$1"
|
|
;;
|
|
*)
|
|
default_do_upgrade "$1"
|
|
;;
|
|
esac
|
|
}
|