forked from mirror/openwrt
10504e0c6b
This device is very similar to the already supported XGS1210-12 A1. For now, only revision A1 is supported (not marked on the label). Hardware: - RTL9302B SoC - 16 MiB NOR flash - 128 MiB DDR3 SDRAM - 8x 1G RJ45 (RTL8218D) - 2x 2.5G RJ45 (2x RTL8226) - 2x SFP+ (supporting 1G/2.5G/10G) - 3.3V UART serial (115200 baud 8N1) on the right side of the case (from bottom to top: GND, RX, TX, VCC) It is originally an unmanaged switch, so there are a few differences: - No reset button - Different partition layout: There is some reserved space in the middle of the flash which might be used by the bootloader for flash testing. The remaining space in between is used for OpenWrt using mtd-concat. The largest contiguous area is at the beginning, allowing a maximum kernel size of 7 MiB. - No individual MAC address: This device ships with an empty U-Boot environment. When an OpenWrt squashfs image is booted for the first time, a random MAC address will be written to the environment (but only if the environment has been initialized from the bootloader before and contains the default MAC address). Steps to boot initramfs image via network: - Configure a TFTP server to provide the OpenWrt initramfs image - Connect to device using serial (see hardware information above) - Power on the device and enter U-Boot using Esc when prompted - Run the following commands (adjust as necessary): # rtk network on # tftpboot 0x84f00000 192.168.1.100:openwrt-xgs1010-initramfs.bin # bootm Installation on flash: - Boot initramfs image as described above - Now is a good time to create a backup of all flash partitions! You'll need this if you want to revert to the unmanaged factory firmware at some point. - Use sysupgrade to install OpenWrt - After restart enter U-Boot again and set the boot command: # setenv bootcmd 'rtk network on; bootm 0xb4900000' # saveenv # run bootcmd Note: The command "rtk network on" is only needed because the drivers currently rely on some setup by the bootloader (without this the RJ45 ports don't work). If the drivers improve in the future, it should be removed (i.e. change the boot command to "bootm 0xb4900000"). Reverting to factory firmware: - Write back your backup of the firmware partition (or write just the fwconcat1 partition, and erase the other two fwconcat partitions) - Change the boot command back to "boota" (or just erase the u-boot-env partition so the default gets used) Signed-off-by: Jan Hoffmann <jan@3e8.eu> Link: https://github.com/openwrt/openwrt/pull/20469 Signed-off-by: Robert Marko <robimarko@gmail.com>
160 lines
3.9 KiB
Makefile
160 lines
3.9 KiB
Makefile
# SPDX-License-Identifier: GPL-2.0-only
|
|
|
|
include ./common.mk
|
|
|
|
define Build/xikestor-nosimg
|
|
$(STAGING_DIR_HOST)/bin/nosimg-enc -i $@ -o $@.new
|
|
mv $@.new $@
|
|
endef
|
|
|
|
define Device/hasivo_s1100w-8xgt-se
|
|
SOC := rtl9303
|
|
DEVICE_VENDOR := Hasivo
|
|
DEVICE_MODEL := S1100W-8XGT-SE
|
|
IMAGE_SIZE := 12288k
|
|
$(Device/kernel-lzma)
|
|
endef
|
|
TARGET_DEVICES += hasivo_s1100w-8xgt-se
|
|
|
|
define Device/plasmacloud-common
|
|
SOC := rtl9302
|
|
UIMAGE_MAGIC := 0x93000000
|
|
DEVICE_VENDOR := Plasma Cloud
|
|
DEVICE_PACKAGES := poemgr
|
|
IMAGE_SIZE := 15872k
|
|
BLOCKSIZE := 64k
|
|
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | uImage lzma
|
|
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | pad-to $$(BLOCKSIZE)
|
|
IMAGES += factory.bin
|
|
IMAGE/factory.bin := append-kernel | append-rootfs | pad-rootfs | check-size
|
|
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
|
endef
|
|
|
|
define Device/plasmacloud_psx8
|
|
$(Device/plasmacloud-common)
|
|
DEVICE_MODEL := PSX8
|
|
endef
|
|
TARGET_DEVICES += plasmacloud_psx8
|
|
|
|
define Device/plasmacloud_psx10
|
|
$(Device/plasmacloud-common)
|
|
DEVICE_MODEL := PSX10
|
|
endef
|
|
TARGET_DEVICES += plasmacloud_psx10
|
|
|
|
define Device/tplink_tl-st1008f-v2
|
|
SOC := rtl9303
|
|
UIMAGE_MAGIC := 0x93030000
|
|
DEVICE_VENDOR := TP-Link
|
|
DEVICE_MODEL := TL-ST1008F
|
|
DEVICE_VARIANT := v2.0
|
|
DEVICE_PACKAGES := kmod-gpio-pca953x
|
|
SUPPORTED_DEVICES += tplink,tl-st1008f,v2
|
|
IMAGE_SIZE := 31808k
|
|
$(Device/kernel-lzma)
|
|
endef
|
|
TARGET_DEVICES += tplink_tl-st1008f-v2
|
|
|
|
define Device/vimin_vm-s100-0800ms
|
|
SOC := rtl9303
|
|
UIMAGE_MAGIC := 0x93000000
|
|
DEVICE_VENDOR := Vimin
|
|
DEVICE_MODEL := VM-S100-0800MS
|
|
IMAGE_SIZE := 13312k
|
|
$(Device/kernel-lzma)
|
|
endef
|
|
TARGET_DEVICES += vimin_vm-s100-0800ms
|
|
|
|
define Device/xikestor_sks8300-8x
|
|
SOC := rtl9303
|
|
DEVICE_VENDOR := XikeStor
|
|
DEVICE_MODEL := SKS8300-8X
|
|
DEVICE_ALT0_VENDOR := ONTi
|
|
DEVICE_ALT0_MODEL := ONT-S508CL-8S
|
|
BLOCKSIZE := 64k
|
|
KERNEL_SIZE := 8192k
|
|
IMAGE_SIZE := 30720k
|
|
IMAGE/sysupgrade.bin := pad-extra 256 | append-kernel | xikestor-nosimg | \
|
|
jffs2 nos.img -e 4KiB -x lzma | pad-to $$$$(KERNEL_SIZE) | \
|
|
append-rootfs | pad-rootfs | append-metadata | check-size
|
|
endef
|
|
TARGET_DEVICES += xikestor_sks8300-8x
|
|
|
|
define Device/xikestor_sks8310-8x
|
|
SOC := rtl9303
|
|
UIMAGE_MAGIC := 0x93000000
|
|
DEVICE_VENDOR := XikeStor
|
|
DEVICE_MODEL := SKS8310-8X
|
|
IMAGE_SIZE := 20480k
|
|
$(Device/kernel-lzma)
|
|
IMAGE/sysupgrade.bin := \
|
|
pad-extra 16 | \
|
|
append-kernel | \
|
|
pad-to 64k | \
|
|
append-rootfs | \
|
|
pad-rootfs | \
|
|
check-size | \
|
|
append-metadata
|
|
endef
|
|
TARGET_DEVICES += xikestor_sks8310-8x
|
|
|
|
define Device/zyxel_xgs1010-12-a1
|
|
SOC := rtl9302
|
|
UIMAGE_MAGIC := 0x93001010
|
|
DEVICE_VENDOR := Zyxel
|
|
DEVICE_MODEL := XGS1010-12
|
|
DEVICE_VARIANT := A1
|
|
KERNEL_SIZE := 7168k
|
|
IMAGE_SIZE := 13184k
|
|
$(Device/kernel-lzma)
|
|
endef
|
|
TARGET_DEVICES += zyxel_xgs1010-12-a1
|
|
|
|
define Device/zyxel_xgs1210-12-a1
|
|
$(Device/zyxel_xgs1210-12)
|
|
SUPPORTED_DEVICES += zyxel,xgs1210-12
|
|
DEVICE_VARIANT := A1
|
|
endef
|
|
TARGET_DEVICES += zyxel_xgs1210-12-a1
|
|
|
|
define Device/zyxel_xgs1210-12-b1
|
|
$(Device/zyxel_xgs1210-12)
|
|
DEVICE_VARIANT := B1
|
|
endef
|
|
TARGET_DEVICES += zyxel_xgs1210-12-b1
|
|
|
|
define Device/zyxel_xgs1250-12-common
|
|
SOC := rtl9302
|
|
UIMAGE_MAGIC := 0x93001250
|
|
ZYXEL_VERS := ABWE
|
|
DEVICE_VENDOR := Zyxel
|
|
DEVICE_MODEL := XGS1250-12
|
|
DEVICE_PACKAGES := kmod-hwmon-gpiofan kmod-thermal
|
|
IMAGE_SIZE := 13312k
|
|
KERNEL := \
|
|
kernel-bin | \
|
|
append-dtb | \
|
|
rt-compress | \
|
|
rt-loader | \
|
|
uImage none
|
|
KERNEL_INITRAMFS := \
|
|
kernel-bin | \
|
|
append-dtb | \
|
|
rt-compress | \
|
|
zyxel-vers | \
|
|
rt-loader | \
|
|
uImage none
|
|
endef
|
|
|
|
define Device/zyxel_xgs1250-12-a1
|
|
$(Device/zyxel_xgs1250-12-common)
|
|
SUPPORTED_DEVICES += zyxel,xgs1250-12
|
|
DEVICE_VARIANT := A1
|
|
endef
|
|
TARGET_DEVICES += zyxel_xgs1250-12-a1
|
|
|
|
define Device/zyxel_xgs1250-12-b1
|
|
$(Device/zyxel_xgs1250-12-common)
|
|
DEVICE_VARIANT := B1
|
|
endef
|
|
TARGET_DEVICES += zyxel_xgs1250-12-b1
|