arne/openwrt
1
0
Fork 0
forked from mirror/openwrt
Code Pull requests Activity
openwrt/target/linux/ath79/dts
History
Lech Perczak 5ac6f56dbe ath79: support ZTE MF286C 
ZTE MF286 is an indoor LTE category 12 CPE router with simultaneous
dual-band 802.11ac plus 802.11n Wi-Fi radios and quad-port gigabit
Ethernet switch, FXS and external USB 2.0 port.

Software-wise it's compatible with previous MF286A, save for different
5GHz Wi-Fi board definition file, requiring a separate image.

Hardware highlights:
- CPU: QCA9563 SoC at 775MHz,
- RAM: 128MB DDR2,
- NOR Flash: MX25L1606E 2MB SPI Flash, for U-boot only,
- NAND Flash: W25N01GV 128MB SPI NAND-Flash, for all other data,
- Wi-Fi 5GHz: QCA9886 2x2 MIMO 802.11ac Wave2 radio,
- WI-Fi 2.4GHz: QCA9563 3x3 MIMO 802.11n radio,
- Switch: QCA8337v2 4-port gigabit Ethernet, with single SGMII CPU port,
- WWAN: MDM9250-based category 12 internal LTE modem
  in extended  mini-PCIE form factor, with 5 internal antennas and
  2 external antenna connections, single mini-SIM slot.
- FXS: one external ATA port (handled entirely by modem part) with two
  physical connections in parallel,
- USB: Single external USB 2.0 port,
- Switches: power switch, WPS, Wi-Fi and reset buttons,
- LEDs: Wi-Fi, Test (internal). Rest of LEDs (Phone, WWAN, Battery,
  Signal state) handled entirely by modem. 4 link status LEDs handled by
  the switch on the backside.
- Label MAC device: eth0

Internal modem of MF286C is supported via uqmi.

Console connection: connector X2 is the console port, with the following
pinout, starting from pin 1, which is the topmost pin when the board is
upright:
- VCC (3.3V). Do not use unless you need to source power for the
  converer from it.
- TX
- RX
- GND
Default port configuration in U-boot as well as in stock firmware is
115200-8-N-1.

Installation:
Due to different flash layout from stock firmware, sysupgrade from
within stock firmware is impossible, despite it's based on QSDK which
itself is based on OpenWrt.

STEP 0: Stock firmware update:
As installing OpenWrt cuts you off from official firmware updates for
the modem part, it is recommended to update the stock firmware to latest
ath79: support ZTE MF286C

STEP 1: Booting initramfs image:

Method 1: using serial console (RECOMMENDED):
- Have TFTP server running, exposing the OpenWrt initramfs image, and
  set your computer's IP address as 192.168.0.22. This is the default
  expected by U-boot. You may wish to change that, and alter later
  commands accordingly.
- Connect the serial console if you haven't done so already,
- Interrupt boot sequence by pressing any key in U-boot when prompted
- Use the following commands to boot OpenWrt initramfs through TFTP:

  setenv serverip 192.168.0.22
  setenv ipaddr 192.168.0.1
  tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286c-initramfs-kernel.bin
  bootm 0x81000000

  (Replace server IP and router IP as needed). There is no  emergency
  TFTP boot sequence triggered by buttons, contrary to MF283+.
- When OpenWrt initramfs finishes booting, proceed to actual
  installation.

STEP 2: Backing up original software:
As the stock firmware may be customized by the carrier and is not
officially available in the Internet, IT IS IMPERATIVE to back up the
stock firmware, if you ever plan to returning to stock firmware.
It is highly recommended to perform backup using both methods, to avoid
hassle of reassembling firmware images in future, if a restore is
needed.

Method 1: after booting OpenWrt initramfs image via TFTP:
- Connect your USB-UART adapter
- Dump stock firmware located on stock kernel and ubi partitions:

  ssh root@192.168.1.1: cat /dev/mtd9 > mtd3_ubiconcat0.bin
  ssh root@192.168.1.1: cat /dev/mtd4 > mtd4_kernel.bin
  ssh root@192.168.1.1: cat /dev/mtd9 > mtd5_ubiconcat1.bin

And keep them in a safe place, should a restore be needed in future.

Method 2: using stock firmware:
- Connect an external USB drive formatted with FAT or ext4 to the USB
  port.
- The drive will be auto-mounted to /var/usb_disk
- Check the flash layout of the device:

  cat /proc/mtd

  It should show the following:
  mtd0: 000a0000 00010000 "u-boot"
  mtd1: 00020000 00010000 "u-boot-env"
  mtd2: 00140000 00010000 "reserved1"
  mtd3: 000a0000 00020000 "fota-flag"
  mtd4: 00080000 00020000 "art"
  mtd5: 00080000 00020000 "mac"
  mtd6: 000c0000 00020000 "reserved2"
  mtd7: 00400000 00020000 "cfg-param"
  mtd8: 00400000 00020000 "log"
  mtd9: 000a0000 00020000 "oops"
  mtd10: 00500000 00020000 "reserved3"
  mtd11: 00800000 00020000 "web"
  mtd12: 00300000 00020000 "kernel"
  mtd13: 01a00000 00020000 "rootfs"
  mtd14: 01900000 00020000 "data"
  mtd15: 03200000 00020000 "fota"
  mtd16: 01d00000 00020000 "firmware"

  Differences might indicate that this is NOT a MF286C device but
  one of other variants.
- Copy over all MTD partitions, for example by executing the following:

  for i in 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15; do cat /dev/mtd$i > \
  /var/usb_disk/mtd$i; done

  "Firmware" partition can be skipped, it is a concatenation
  of "kernel" and "rootfs".

- If the count of MTD partitions is different, this might indicate that
  this is not a MF286C device, but one of its other variants.
- (optionally) rename the files according to MTD partition names from
  /proc/mtd
- Unmount the filesystem:

  umount /var/usb_disk; sync

  and then remove the drive.
- Store the files in safe place if you ever plan to return to stock
  firmware. This is especially important, because stock firmware for
  this device is not available officially, and is usually customized by
  the mobile providers.

STEP 3: Actual installation:
- Set your computer IP to 192.168.1.22/24
- scp the sysupgrade image to the device:

  scp -O openwrt-ath79-nand-zte_mf286a-squashfs-sysupgrade.bin \
  root@192.168.1.1:/tmp/

- ssh into the device and execute sysupgrade:

  sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286a-squashfs-sysupgrade.bin

- Wait for router to reboot to full OpenWrt.

STEP 4: WAN connection establishment
Since the router is equipped with LTE modem as its main WAN interface, it
might be useful to connect to the Internet right away after
installation. To do so, please put the following entries in
/etc/config/network, replacing the specific configuration entries with
one needed for your ISP:

config interface 'wan'
        option proto 'qmi'
        option device '/dev/cdc-wdm0'
        option auth '<auth>' # As required, usually 'none'
        option pincode '<pin>' # If required by SIM
        option apn '<apn>' # As required by ISP
        option pdptype '<pdp>' # Typically 'ipv4', or 'ipv4v6' or 'ipv6'

For example, the following works for most polish ISPs
config interface 'wan'
        option proto 'qmi'
        option device '/dev/cdc-wdm0'
        option auth 'none'
        option apn 'internet'
        option pdptype 'ipv4'

The required minimum is:
config interface 'wan'
        option proto 'qmi'
        option device '/dev/cdc-wdm0'
In this case, the modem will use last configured APN from stock
firmware - this should work out of the box, unless your SIM requires
PIN which can't be switched off.

If you have build with LuCI, installing luci-proto-qmi helps with this
task.

Restoring the stock firmware:

- Boot to initramfs as in step 3:
- Completely detach ubi0 partition using ubidetach /dev/ubi0_0
- Copy over the stock kernel image using scp to /tmp
- Erase kernel and restore stock kernel:
  (scp mtd4_kernel.bin root@192.168.1.1:/tmp/)
  mtd write kernel /tmp/mtd4_kernel.bin
  rm /tmp/mtd4_kernel.bin
- Copy over the stock partition backups one-by-one using scp to /tmp, and
  restore them individually. Otherwise you might run out of space in
  tmpfs:

  (scp -O mtd3_ubiconcat0.bin root@192.168.1.1:/tmp/)

  mtd write ubiconcat0 /tmp/mtd3_ubiconcat0.bin
  rm /tmp/mtd3_ubiconcat0.bin

  (scp -O mtd5_ubiconcat1.bin root@192.168.1.1:/tmp/)

  mtd write ubiconcat1 /tmp/mtd5_ubiconcat1.bin
  rm /tmp/mtd5_ubiconcat1.bin

- If the write was correct, force a device reboot with

  reboot -f

Quirks and known issues
- It was observed, that CH340-based USB-UART converters output garbage
  during U-boot phase of system boot. At least CP2102 is known to work
  properly.
- Kernel partition size is increased to 4MB compared to stock 3MB, to
  accomodate future kernel updates - at this moment OpenWrt 5.10 kernel
  image is at 2.5MB which is dangerously close to the limit. This has no
  effect on booting the system - but keep that in mind when reassembling
  an image to restore stock firmware.
- uqmi seems to be unable to change APN manually, so please use the one
  you used before in stock firmware first. If you need to change it,
  please use protocok '3g' to establish connection once, or use the
  following command to change APN (and optionally IP type) manually:
  echo -ne 'AT+CGDCONT=1,"IP","<apn>' > /dev/ttyUSB0
- The only usable LED as a "system LED" is the blue debug LED hidden
  inside the case. All other LEDs are controlled by modem, on which the
  router part has some influence only on Wi-Fi LED.
- GPIO5 used for modem reset is a suicide switch, causing a hardware
  reset of whole board, not only the modem. It is attached to
  gpio-restart driver, to restart the modem on reboot as well, to ensure
  QMI connectivity after reboot, which tends to fail otherwise.
- Modem, as in MF283+, exposes root shell over ADB - while not needed
  for OpenWrt operation at all - have fun lurking around.
  The same modem module is used as in older MF286.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17620
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2025-03-16 22:10:04 +01:00
..
ar724x.dtsi ath79: correct dts ngpios properties 2024-07-04 19:30:37 +02:00
ar724x_senao_loader-4k.dtsi ath79: add Senao 'failsafe' sysupgrade procedure 2021-04-08 09:20:59 +02:00
ar724x_senao_loader-64k.dtsi ath79: add Senao 'failsafe' sysupgrade procedure 2021-04-08 09:20:59 +02:00
ar724x_ubnt_xm.dtsi ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar724x_ubnt_xm_outdoor.dtsi ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar934x.dtsi ath79: usb: remove reset names 2024-12-13 15:29:04 +01:00
ar934x_ruckus_zf73xx.dtsi linux: replace u-boot,env with nvmem,layout 2024-12-27 13:34:58 +01:00
ar934x_senao_loader.dtsi ath79: add Senao 'failsafe' sysupgrade procedure 2021-04-08 09:20:59 +02:00
ar1022_iodata_wn-ag300dgr.dts ath79: enable UART in SoC DTSI files 2021-02-24 02:53:53 +01:00
ar1022_sitecom_wlr-7100.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar7100.dtsi ath79: usb: remove reset names 2024-12-13 15:29:04 +01:00
ar7100_mikrotik_routerboard-4xx.dtsi ath79: correct dts ngpios properties 2024-07-04 19:30:37 +02:00
ar7161_adtran_bsap1800-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_adtran_bsap1840.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_adtran_bsap1880.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_aruba_ap-105.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_aruba_ap-175.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_buffalo_wzr-600dhp.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_buffalo_wzr-hp-ag300h.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_buffalo_wzr-hp-ag300h.dtsi ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar7161_dlink_dir-825-b1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_fortinet_fap-220-b.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_jjplus_ja76pf2.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7161_meraki_mr16.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_mikrotik_routerboard-493g.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_netgear_wndap360.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_netgear_wndr.dtsi ath79: add back usb LED label for NETGEAR WNDR3x00 devices 2024-06-20 14:02:13 +02:00
ar7161_netgear_wndr3700-v2.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar7161_netgear_wndr3700.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar7161_netgear_wndr3800.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar7161_netgear_wndr3800ch.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar7161_netgear_wndrmac-v1.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar7161_netgear_wndrmac-v2.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar7161_ruckus_gd11.dtsi linux: replace u-boot,env with nvmem,layout 2024-12-27 13:34:58 +01:00
ar7161_ruckus_zf734x.dtsi ath79: support Ruckus ZoneFlex 7341/7343/7363 2023-03-22 22:25:08 +01:00
ar7161_ruckus_zf7341.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7161_ruckus_zf7351.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7161_ruckus_zf7363.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7161_siemens_ws-ap3610.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_trendnet_tew-673gru.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7161_ubnt_routerstation-pro.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_ubnt_routerstation.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7161_ubnt_routerstation.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar7240.dtsi ath79: usb: remove reset names 2024-12-13 15:29:04 +01:00
ar7240_buffalo_whr-g301n.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar7240_dlink_dir-615-e4.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7240_engenius_enh202-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7240_netgear_wnr612-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_netgear_wnr612-v2.dtsi ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar7240_netgear_wnr1000-v2.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar7240_on_n150r.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_openmesh_om2p-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7240_ruckus_zf7025.dts linux: replace u-boot,env with nvmem,layout 2024-12-27 13:34:58 +01:00
ar7240_tplink.dtsi ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar7240_tplink_tl-wa.dtsi ath79: fix tl-wa eth1 mac 2024-12-16 11:06:11 +01:00
ar7240_tplink_tl-wa701nd-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wa730re-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wa801nd-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wa830re-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wa901nd-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wr.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7240_tplink_tl-wr740n-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wr740n-v3.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wr741-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wr743nd-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wr841-v5.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_tplink_tl-wr941-v4.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7240_ubnt_bullet-m-ar7240.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241.dtsi ath79: usb: remove reset names 2024-12-13 15:29:04 +01:00
ar7241_netgear_wnr2000-v3.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar7241_netgear_wnr2200-8m.dts ath79: use nvmem for wrong 3e0 cal size 2024-12-23 23:46:41 +01:00
ar7241_netgear_wnr2200-16m.dts ath79: use nvmem for wrong 3e0 cal size 2024-12-23 23:46:41 +01:00
ar7241_netgear_wnr2200.dtsi ath79: use nvmem for wrong 3e0 cal size 2024-12-23 23:46:41 +01:00
ar7241_tplink.dtsi ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar7241_tplink_tl-mr3x20.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
ar7241_tplink_tl-mr3220-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7241_tplink_tl-mr3420-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7241_tplink_tl-wr841-v7.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7241_tplink_tl-wr842n-v1.dts ath79: use nvmem for wrong 3e0 cal size 2024-12-23 23:46:41 +01:00
ar7241_ubnt_airrouter.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7241_ubnt_bullet-m-ar7241.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_nanobridge-m.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_nanostation-loco-m.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_nanostation-m.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_picostation-m.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_powerbridge-m.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_rocket-m.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar7241_ubnt_unifi-ap-lr.dts ath79: add variant UniFi AP LR 2022-08-06 20:15:30 +02:00
ar7241_ubnt_unifi-ap-outdoor-plus.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7241_ubnt_unifi-ap.dts ath79: rename references of UniFi to UniFi AP 2022-08-06 20:15:30 +02:00
ar7241_ubnt_unifi-ap.dtsi ath79: fix calibration size for AR9287 2024-12-23 23:46:41 +01:00
ar7241_ubnt_unifi.dtsi ath79: convert WiFis based on ar7241_ubnt_unifi.dtsi to nvmem-cells 2022-12-17 20:48:57 +01:00
ar7242.dtsi ath79: usb: remove reset names 2024-12-13 15:29:04 +01:00
ar7242_avm_fritz300e.dts ath79: add missing compatible for ath9k 2024-12-30 13:50:04 +01:00
ar7242_buffalo_bhr-4grv.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7242_buffalo_wzr-bhr.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7242_buffalo_wzr-hp-g302h-a1a0.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7242_buffalo_wzr-hp-g450h.dts ath79: apply qca,tx-gain-buffalo 2024-10-19 17:30:50 +02:00
ar7242_engenius_eap350-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7242_engenius_ecb350-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7242_meraki_mr12.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar7242_tplink_tl-wr2543-v1.dts ath79: wr2543: add compatible string for wifi 2024-12-23 23:46:41 +01:00
ar7242_ubnt_edgeswitch-5xp.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7242_ubnt_edgeswitch-8xp.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar7242_ubnt_sw.dtsi ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar9132.dtsi ath79: usb: remove usb- from reset-names 2024-12-13 15:29:04 +01:00
ar9132_buffalo_wzr-hp-g300nh-rb.dts ath79: Add support for Buffalo WZR-HP-G300NH 2021-03-22 09:23:10 +01:00
ar9132_buffalo_wzr-hp-g300nh-s.dts ath79: Add support for Buffalo WZR-HP-G300NH 2021-03-22 09:23:10 +01:00
ar9132_buffalo_wzr-hp-g300nh.dtsi ath79: fix ath9k calibration data size for AR9132 2024-12-15 22:31:31 +01:00
ar9132_tplink_tl-wa901nd-v2.dts ath79: fix ath9k calibration data size for AR9132 2024-12-15 22:31:31 +01:00
ar9132_tplink_tl-wr941-v2.dts ath79: fix ath9k calibration data size for AR9132 2024-12-15 22:31:31 +01:00
ar9132_tplink_tl-wr1043nd-v1.dts ath79: fix ath9k calibration data size for AR9132 2024-12-15 22:31:31 +01:00
ar9330.dtsi ath79: usb: remove reset names 2024-12-13 15:29:04 +01:00
ar9330_dlink_dir-505.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar9330_glinet_gl-ar150.dts ath79: gl-ar150: fix USB GPIO usage 2025-01-12 18:01:35 +01:00
ar9330_openmesh_om2p-lc.dts ath79: Add support for OpenMesh OM2P-LC 2020-12-30 23:32:07 +01:00
ar9330_openmesh_om2p-v2.dts ath79: Add support for OpenMesh OM2P v2 2020-12-30 23:32:07 +01:00
ar9330_openmesh_om2p.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9330_pqi_air-pen.dts ath79: pqi-air-pen: adjust mac addresses 2024-12-13 15:29:04 +01:00
ar9330_ziking_cpe46b.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9331.dtsi ath79: add missing clock name strings in SoC dtsi 2022-11-09 22:55:33 +01:00
ar9331_8dev_carambola2.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9331_alfa-network_ap121f.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar9331_alfa-network_ap121f.dtsi ath79: remove wmac mac address defaults 2024-11-30 18:55:17 +01:00
ar9331_alfa-network_ap121fe.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar9331_arduino_yun.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9331_embeddedwireless_dorin.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9331_etactica_eg200.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9331_glinet_64xx.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9331_glinet_6408.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9331_glinet_6416.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9331_glinet_gl-mifi.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9331_glinet_gl-usb150.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9331_hak5_lan-turtle.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar9331_hak5_lan-turtle.dtsi ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar9331_hak5_packet-squirrel.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
ar9331_hak5_wifi-pineapple-nano.dts ath79: pineapple-nano: use regulator for USB GPIO 2025-01-12 18:01:35 +01:00
ar9331_hiwifi_hc6361.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9331_onion_omega.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9331_pisen_ts-d084.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9331_pisen_wmm003n.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9331_teltonika_rut230-v1.dts ath79: teltonika-rut230: fully support digital output lines 2025-01-12 21:36:04 +01:00
ar9331_tplink_tl-mr10u.dts ath79: gpio to gpios 2024-01-05 16:17:58 +01:00
ar9331_tplink_tl-mr3020-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9331_tplink_tl-mr3040-v2.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9331_tplink_tl-wr703n.dts ath79: gpio to gpios 2024-01-05 16:17:58 +01:00
ar9331_tplink_tl-wr703n_tl-mr10u.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9331_tplink_tl-wr710n-8m.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9331_tplink_tl-wr710n-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9331_tplink_tl-wr710n-v2.1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9331_tplink_tl-wr710n.dtsi ath79: gpio to gpios 2024-01-05 16:17:58 +01:00
ar9331_tplink_tl-wr740n-v4.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9331_tplink_tl-wr740n-v5.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9331_tplink_tl-wr741nd-v4.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9331_tplink_tl-wr741nd-v4.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9341.dtsi ath79: do not set inherited phy-mode/status properties again 2020-01-31 13:42:12 +01:00
ar9341_engenius_eap300-v2.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9341_engenius_ens202ext-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9341_openmesh_om2p-hs-v1.dts ath79: add support for OpenMesh OM2P-HS v1 2020-12-29 00:03:26 +01:00
ar9341_openmesh_om2p-hs-v2.dts ath79: add support for OpenMesh OM2P-HS v2 2020-12-29 00:03:26 +01:00
ar9341_openmesh_om2p-hs-v3.dts ath79: add support for OpenMesh OM2P-HS v3 2020-12-29 00:03:26 +01:00
ar9341_openmesh_om2p-hs.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9341_pcs_cr3000.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9341_pisen_wmb001n.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9341_tplink.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9341_tplink_tl-mr3420-v2.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9341_tplink_tl-wa.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9341_tplink_tl-wa850re-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9341_tplink_tl-wa860re-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9341_tplink_tl-wa901nd-v3.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9341_tplink_tl-wr841-v8.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9341_tplink_tl-wr842n-v2.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9341_tplink_tl-wr941nd-v5.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9342_iodata_etg3-r.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9342_mikrotik_routerboard-911g-xhpnd.dts ath79: mikrotik: fix reference clock of Routerboard 911G 2025-02-13 00:24:14 +01:00
ar9342_mikrotik_routerboard-911g.dtsi ath79: mikrotik: fix reference clock of Routerboard 911G 2025-02-13 00:24:14 +01:00
ar9342_mikrotik_routerboard-912uag-2hpnd.dts ath79: mikrotik: fix reference clock of Routerboard 911G 2025-02-13 00:24:14 +01:00
ar9342_ruckus_zf7321.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9342_ubnt_aircube-ac.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar9342_ubnt_bullet-ac.dts ath79: Add support for Ubiquiti Bullet AC 2021-01-15 18:32:38 +01:00
ar9342_ubnt_bullet-m-xw.dts ath79: ubnt-bullet-m-xw: fix Ethernet PHY traffic 2024-01-25 23:45:41 +01:00
ar9342_ubnt_lap-120.dts ath79: create DTSI files for ubnt WA 1-/2-port devices 2020-11-03 18:34:10 +01:00
ar9342_ubnt_litebeam-ac-gen2.dts ath79: remove redundant setup of wmac for ubnt WA devices 2020-11-03 18:34:10 +01:00
ar9342_ubnt_litebeam-m5-xw.dts ath79: generic: rework ar9342_ubnt_xw dtsi, and add support for Ubiquiti LiteBeam M5 (XW), Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) 2024-01-20 19:57:57 +01:00
ar9342_ubnt_nanobeam-ac-gen2.dts ath79: Add support for Ubiquiti NanoBeam AC Gen2 2020-11-18 21:13:46 +01:00
ar9342_ubnt_nanobeam-ac.dts ath79: Add support for Ubiquiti NanoBeam AC Gen2 2020-11-18 21:13:46 +01:00
ar9342_ubnt_nanostation-ac-loco.dts ath79: remove redundant setup of wmac for ubnt WA devices 2020-11-03 18:34:10 +01:00
ar9342_ubnt_nanostation-ac.dts ath79: remove redundant setup of wmac for ubnt WA devices 2020-11-03 18:34:10 +01:00
ar9342_ubnt_nanostation-loco-m-xw.dts ath79: generic: rework ar9342_ubnt_xw dtsi, and add support for Ubiquiti LiteBeam M5 (XW), Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) 2024-01-20 19:57:57 +01:00
ar9342_ubnt_nanostation-m-xw.dts ath79: generic: rework ar9342_ubnt_xw dtsi, and add support for Ubiquiti LiteBeam M5 (XW), Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) 2024-01-20 19:57:57 +01:00
ar9342_ubnt_powerbeam-5ac-gen2.dts ath79: create DTSI files for ubnt WA 1-/2-port devices 2020-11-03 18:34:10 +01:00
ar9342_ubnt_powerbeam-m2-xw.dts ath79: generic: rework ar9342_ubnt_xw dtsi, and add support for Ubiquiti LiteBeam M5 (XW), Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) 2024-01-20 19:57:57 +01:00
ar9342_ubnt_powerbeam-m5-xw.dts ath79: generic: rework ar9342_ubnt_xw dtsi, and add support for Ubiquiti LiteBeam M5 (XW), Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) 2024-01-20 19:57:57 +01:00
ar9342_ubnt_wa.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9342_ubnt_wa_1port.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9342_ubnt_wa_2port.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
ar9342_ubnt_xw.dtsi ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar9342_ubnt_xw_rssileds.dtsi ath79: generic: rework ar9342_ubnt_xw dtsi, and add support for Ubiquiti LiteBeam M5 (XW), Ubiquiti AirGrid M5 HP (XW), Ubiquiti PowerBeam M5 300 (XW) 2024-01-20 19:57:57 +01:00
ar9342_zyxel_nwa11xx.dtsi ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar9342_zyxel_nwa1100-nh.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9342_zyxel_nwa1121-ni.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9342_zyxel_nwa1123-ac.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9342_zyxel_nwa1123-ni.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344.dtsi ath79: rename pcie-controller to pcie 2024-01-05 16:17:57 +01:00
ar9344_aerohive_hiveap-121.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_alfa-network_n5q.dts ath79: remove wmac mac address defaults 2024-11-30 18:55:17 +01:00
ar9344_araknis_an-300-ap-i-n.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_atheros_db120.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_comfast_cf-e120a-v3.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9344_compex_wpj344-16m.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9344_devolo_dlan-pro-1200plus-ac.dts ath79: add support for Devolo dLAN pro 1200+ WiFi ac 2021-06-06 18:56:45 +02:00
ar9344_devolo_dlan_wifi.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9344_devolo_magic-2-wifi.dts ath79: add support for Devolo dLAN pro 1200+ WiFi ac 2021-06-06 18:56:45 +02:00
ar9344_dlink_dir-8x5.dtsi ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar9344_dlink_dir-825-c1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_dlink_dir-835-a1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_embeddedwireless_balin.dts ath79: remove wmac mac address defaults 2024-11-30 18:55:17 +01:00
ar9344_engenius_eap600.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_engenius_ecb600.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_enterasys_ws-ap3705i.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_fortinet_ap-dual.dtsi ath79: fix pci_device_reg errors 2024-01-05 16:17:58 +01:00
ar9344_fortinet_fap-221-b.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_huawei_ap6010dn.dts ath79: add support for Huawei AP6010DN 2024-07-21 16:51:52 +02:00
ar9344_longdata_aps256.dts ath79: add support for Longdata APS256 2025-03-15 13:35:41 +01:00
ar9344_mercury_mw4530r-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_mikrotik_routerboard-16m-nor.dtsi ath79: mikrotik: stack ar9344 devices to single dtsi 2023-02-26 22:22:48 +01:00
ar9344_mikrotik_routerboard-911-lite.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_mikrotik_routerboard-951g-2hnd.dts ath79: DTS improvement for buzzer on RB951G-2HnD 2023-07-01 15:51:26 +02:00
ar9344_mikrotik_routerboard-951ui-2hnd.dts ath79: mikrotik: extract common bits for RB951x-2HnD devices 2023-06-25 13:18:31 +02:00
ar9344_mikrotik_routerboard-951x-2hnd.dtsi ath79: mikrotik: extract common bits for RB951x-2HnD devices 2023-06-25 13:18:31 +02:00
ar9344_mikrotik_routerboard-lhg-5nd.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_mikrotik_routerboard-sxt-5nd-r2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_mikrotik_routerboard.dtsi ath79: mikrotik: stack ar9344 devices to single dtsi 2023-02-26 22:22:48 +01:00
ar9344_moxa_awk-1137c.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar9344_nec_aterm.dtsi ath79: remove dr_mode and vbus-supply 2025-01-08 14:55:28 +01:00
ar9344_nec_wg600hp.dts ath79: add support for NEC Aterm WG600HP 2024-07-28 18:47:56 +02:00
ar9344_nec_wr8750n.dts ath79: add support for NEC Aterm WR8750N 2024-07-28 18:47:56 +02:00
ar9344_nec_wr9500n.dts ath79: add support for NEC Aterm WR9500N 2024-07-28 18:47:56 +02:00
ar9344_netgear_pgzng1.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar9344_netgear_r6100.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_netgear_wndr.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_netgear_wndr3700-v4.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_netgear_wndr4300.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_netgear_wndr4300sw.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_netgear_wndr4300tn.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_netgear_wndr_usb.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_netgear_wndr_wan.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_ocedo_raccoon.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_openmesh_mr600-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_openmesh_mr600-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_openmesh_mr600.dtsi ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar9344_openmesh_om5p-an.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_openmesh_om5p.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9344_pcs_cap324.dts ath79: convert pcs,cap324 calibration to nvmem 2024-06-09 12:24:15 +02:00
ar9344_pcs_cr5000.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9344_qihoo_c301.dts ath79: remove dr_mode and vbus-supply 2025-01-08 14:55:28 +01:00
ar9344_qxwlan_e750a-v4-8m.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_qxwlan_e750a-v4-16m.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_qxwlan_e750g-v8-8m.dts ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar9344_qxwlan_e750g-v8-16m.dts ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar9344_qxwlan_e750x.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9344_ruckus_zf7372.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_samsung_wam250.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9344_senao_ap-dual.dtsi ath79: fix pci_device_reg errors 2024-01-05 16:17:58 +01:00
ar9344_teltonika_rut9xx.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9344_teltonika_rut955-h7v3c0.dts ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar9344_teltonika_rut955.dts ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar9344_tplink_cpe.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9344_tplink_cpe210-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_cpe220-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_cpe510-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_cpe510-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_cpe510-v3.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_cpe605-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_tplink_cpe610-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_tplink_cpe610-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_tplink_cpe_1port.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_tplink_cpe_2port.dtsi ath79: remove redundant nvmem definitions 2021-08-20 18:13:55 +02:00
ar9344_tplink_tl-wdr3500-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_tplink_tl-wdr3600-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_tl-wdr4300-v1-il.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_tl-wdr4300-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_tl-wdr4300.dtsi ath79: ar: convert to mac-base 2023-11-25 21:34:18 -08:00
ar9344_tplink_tl-wdr4310-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_tl-wdrxxxx.dtsi ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar9344_tplink_tl-wr841hp-v2.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
ar9344_tplink_wbs210-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_wbs210-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_wbs510-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_tplink_wbs510-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
ar9344_ubnt_unifi-ap-pro.dts ath79: ar: convert to nvmem-layout 2023-11-25 21:34:18 -08:00
ar9344_watchguard_ap100.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_watchguard_ap200.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_wd_mynet-n600.dts ath79: drop redundant label with new LED color/function format 2024-02-07 14:48:34 +01:00
ar9344_wd_mynet-n750.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_wd_mynet-nxxx.dtsi ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar9344_wd_mynet-wifi-rangeextender.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
ar9344_winchannel_wb2000.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
ar9344_zbtlink_zbt-wd323.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
arxxxx_fortinet_loader.dtsi ath79: fortinet-fap-220-b: convert to nvmem-layout 2023-11-27 00:34:49 +01:00
ath79.dtsi ath79: skip reset control for syscon devices 2024-05-09 23:53:02 +02:00
qca953x.dtsi ath79: remove dr_mode and vbus-supply 2025-01-08 14:55:28 +01:00
qca953x_dlink_dap-2xxx.dtsi ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca953x_tplink_tl-wr810n.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca955x.dtsi ath79: usb: remove reset names 2024-12-13 15:29:04 +01:00
qca955x_dlink_dap-2xxx.dtsi ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca955x_elecom_wab.dtsi ath79: remove dr_mode and vbus-supply 2025-01-08 14:55:28 +01:00
qca955x_engenius_ecb1xxx.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca955x_senao_loader.dtsi linux: replace u-boot,env with nvmem,layout 2024-12-27 13:34:58 +01:00
qca955x_senao_router-dual.dtsi ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
qca955x_ubnt_xc.dtsi ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
qca955x_zyxel_nbg6x16.dtsi ath79: nbg6x16: use nvmem 2024-12-22 23:36:41 +01:00
qca956x.dtsi ath79: usb: remove reset names 2024-12-13 15:29:04 +01:00
qca9531_8dev_carambola3.dts ath79: remove dr_mode and vbus-supply 2025-01-08 14:55:28 +01:00
qca9531_8dev_lima.dts ath79: remove dr_mode and vbus-supply 2025-01-08 14:55:28 +01:00
qca9531_alcatel_hh40v.dts ath79: remove dr_mode and vbus-supply 2025-01-08 14:55:28 +01:00
qca9531_alfa-network_n2q.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_alfa-network_pi-wifi4.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_alfa-network_r36a.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_alfa-network_r36a.dtsi ath79: remove wmac mac address defaults 2024-11-30 18:55:17 +01:00
qca9531_alfa-network_tube-2hq.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_alfa-network_wifi-camppro-nano-duo.dts ath79: add support for ALFA Network WiFi CampPro Nano Duo 2024-10-22 12:25:58 +02:00
qca9531_asus_rp-ac51.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
qca9531_comfast_cf-e5.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_comfast_cf-e130n-v2.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_comfast_cf-e313ac.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
qca9531_comfast_cf-e314n-v2.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_comfast_cf-e355ac-v2.dts ath79: add support for COMFAST CF-E355AC v2 2024-10-20 22:07:32 +02:00
qca9531_comfast_cf-e560ac.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_comfast_cf-ew71-v2.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_comfast_cf-ew72.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_comfast_cf-wr752ac-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_compex_wpj531-16m.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_dlink_dch-g020-a1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_engenius_ews511ap.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_glinet_gl-ar300m-lite.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_glinet_gl-ar300m-nand.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9531_glinet_gl-ar300m-nor.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9531_glinet_gl-ar300m.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_glinet_gl-ar300m16.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9531_glinet_gl-ar750.dts ath79: fix I2C pins on GL-AR750 2024-09-21 18:03:31 +02:00
qca9531_glinet_gl-e750.dts ath79: gl-e750: use nvmem for mac addresses 2024-12-08 23:36:24 +01:00
qca9531_glinet_gl-s200-nor-nand.dts ath79: add support for GL.iNet GL-S200 2023-10-31 13:53:11 +01:00
qca9531_glinet_gl-s200-nor.dts ath79: add support for GL.iNet GL-S200 2023-10-31 13:53:11 +01:00
qca9531_glinet_gl-s200.dtsi ath79: correct dts ngpios properties 2024-07-04 19:30:37 +02:00
qca9531_glinet_gl-x300b.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_glinet_gl-x750.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_glinet_gl-xe300.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_joyit_jt-or750i.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_letv_lba-047-ch.dts ath79: drop redundant label with new LED color/function format 2024-02-07 14:48:34 +01:00
qca9531_mikrotik_routerboard-951ui-2nd.dts ath79: add support for MikroTik hAP (RB951Ui-2nD) 2022-05-21 13:54:08 +02:00
qca9531_qxwlan_e600g-v2-8m.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_qxwlan_e600g-v2-16m.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_qxwlan_e600g.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_qxwlan_e600gac-v2-8m.dts ath79: add support for Qxwlan E600G v2 / E600GAC v2 2020-11-12 17:18:26 +01:00
qca9531_qxwlan_e600gac-v2-16m.dts ath79: add support for Qxwlan E600G v2 / E600GAC v2 2020-11-12 17:18:26 +01:00
qca9531_telco_t1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_teltonika_rut300.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9531_tplink_archer-d50-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_tplink_tl-mr3420-v3.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_tplink_tl-mr6400-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_tplink_tl-wr810n-v1.dts ath79: remove dr_mode and vbus-supply 2025-01-08 14:55:28 +01:00
qca9531_tplink_tl-wr902ac-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_wallys_dr531.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9531_yuncore_a770.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9533_comfast_cf-e110n-v2.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9533_dlink_dap-13xx.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9533_dlink_dap-1330-a1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_dlink_dap-1365-a1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_dlink_dap-2230-a1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_dlink_dap-3320-a1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_kuwfi_c910.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_mikrotik_routerboard-16m.dtsi ath79: add support for MikroTik RouterBOARD 750 r2 (hEX lite) 2023-09-16 12:49:26 +02:00
qca9533_mikrotik_routerboard-95x.dtsi ath79: add support for MikroTik RouterBOARD 750 r2 (hEX lite) 2023-09-16 12:49:26 +02:00
qca9533_mikrotik_routerboard-750-r2.dts ath79: add support for MikroTik RouterBOARD 750 r2 (hEX lite) 2023-09-16 12:49:26 +02:00
qca9533_mikrotik_routerboard-952ui-5ac2nd.dts ath79: add support for MikroTik RouterBOARD hAP ac lite 2022-05-21 13:54:02 +02:00
qca9533_mikrotik_routerboard-lhg-2nd.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_mikrotik_routerboard-lhg-hb.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_mikrotik_routerboard-map-2nd.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_mikrotik_routerboard-mapl-2nd.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_mikrotik_routerboard-wap-2nd.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_mikrotik_routerboard-wapr-2nd.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_openmesh_om2p-hs-v4.dts ath79: Add support for OpenMesh OM2P-HS v4 2020-12-28 19:37:24 +01:00
qca9533_openmesh_om2p-v4.dts ath79: Add support for OpenMesh OM2P v4 2020-12-28 19:37:24 +01:00
qca9533_openmesh_om2p-v4.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9533_plasmacloud_pa300.dts ath79: Add support for Plasma Cloud PA300 2020-12-22 19:11:50 +01:00
qca9533_plasmacloud_pa300.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9533_plasmacloud_pa300e.dts ath79: Add support for Plasma Cloud PA300E 2020-12-22 19:11:50 +01:00
qca9533_qca_ap143-8m.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9533_qca_ap143-16m.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9533_qca_ap143.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_tplink_cpe210-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_cpe210-v3.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_cpe210.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_tplink_cpe220-v3.dts ath79: remove redundant nvmem definitions 2021-08-20 18:13:55 +02:00
qca9533_tplink_cpexxx.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9533_tplink_tl-wa801nd-v3.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wa801nd-v4.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wa801nd.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9533_tplink_tl-wa850re-v2.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9533_tplink_tl-wr802n-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr802n-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr802n.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9533_tplink_tl-wr810n-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr841-v9.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr841-v10.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr841-v11.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr841-v11.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9533_tplink_tl-wr841-v12.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9533_tplink_tl-wr841.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9533_tplink_tl-wr841hp-v3.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9533_tplink_tl-wr842n-v3.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9533_ubnt_aircube-isp.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9533_yuncore_a930.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9533_yuncore_cpe830.dts ath79: add support for KuWfi CPE830(D) / YunCore CPE830(D) 2024-12-26 15:19:25 +01:00
qca9550_airtight_c-75.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9550_dell_apl26-0ae.dts ath79: add support for Dell SonicPoint ACe APL26-0AE 2024-05-27 00:32:57 +02:00
qca9550_huawei_ap5030dn.dts ath79: ap5030dn: use label-mac-device property 2024-12-21 12:20:10 +01:00
qca9556_avm_fritz-repeater.dtsi ath79: convert ath10k calibration data to NVMEM (built-in MAC) 2024-02-01 17:09:02 +01:00
qca9556_avm_fritz450e.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9556_avm_fritz1750e.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9556_avm_fritzdvbc.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9556_mikrotik_routerboard-wap-g-5hact2hnd.dts ath79: add aliases to qca955x.dtsi for uart0/1 2024-03-08 17:35:01 +01:00
qca9557_8dev_rambutan.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9557_araknis_an-500-ap-i-ac.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9557_buffalo_bhr-4grv2.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
qca9557_dlink_dap-2660-a1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9557_dongwon_dw02-412h-64m.dts ath79: improve support for Dongwon T&I DW02-412H 2022-02-01 14:54:16 +09:00
qca9557_dongwon_dw02-412h-128m.dts ath79: improve support for Dongwon T&I DW02-412H 2022-02-01 14:54:16 +09:00
qca9557_dongwon_dw02-412h.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9557_elecom_wab-s600-ps.dts ath79: add support for ELECOM WAB-S600-PS 2024-03-02 14:08:08 +01:00
qca9557_elecom_wab-s1167-ps.dts ath79: add support for ELECOM WAB-S1167-PS 2024-03-02 14:08:08 +01:00
qca9557_engenius_eap1200h.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9557_engenius_ecb1200.dts ath79: create common DTSI for ECB1200 and ECB1750 2020-12-22 19:11:50 +01:00
qca9557_engenius_enstationac-v1.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
qca9557_engenius_esr1200.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9557_extreme-networks_ws-ap3805i.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9557_fortinet_fap-221-c.dts ath79: add support for Fortinet FAP-221-C 2025-03-09 19:57:26 +01:00
qca9557_iodata_wn-ac-dgr.dtsi ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
qca9557_iodata_wn-ac1167dgr.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9557_iodata_wn-ac1600dgr.dts ath79: convert ath10k calibration data to NVMEM (ASCII MAC) 2024-02-01 17:09:03 +01:00
qca9557_iodata_wn-ac1600dgr2.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9557_meraki_mr18.dts ath79: drop unnecessary &uart node from dtsi of QCA955x devices 2024-03-08 17:35:01 +01:00
qca9557_ruckus_r500.dts ath79: add support for Ruckus R500 2025-01-20 23:59:45 +01:00
qca9557_sophos_ap15.dts ath79: Unify Sophos AP15/AP15C dts files 2024-11-30 18:19:52 +01:00
qca9557_sophos_ap15.dtsi ath79: Unify Sophos AP15/AP15C dts files 2024-11-30 18:19:52 +01:00
qca9557_sophos_ap15c.dts ath79: Unify Sophos AP15/AP15C dts files 2024-11-30 18:19:52 +01:00
qca9557_zyxel_nbg6616.dts ath79: nbg6x16: use nvmem 2024-12-22 23:36:41 +01:00
qca9558_allnet_all-wap02860ac.dts ath79: fix MAC address for senao loader devices 2024-06-14 21:05:19 +02:00
qca9558_araknis_an-700-ap-i-ac.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_aruba_ap-115.dts ath79: remove dr_mode and vbus-supply 2025-01-08 14:55:28 +01:00
qca9558_belkin_f9j1108-v2.dts ath79: create shared DTSI/definition for Belkin F9J1108/F9K1115 v2 2020-12-14 16:57:21 +01:00
qca9558_belkin_f9k1115-v2.dts ath79: add support for the Belkin F9K1115 v2 (AC1750 DB Wi-Fi) 2020-12-14 16:59:49 +01:00
qca9558_belkin_f9x-v2.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_buffalo_wzr-450hp2.dts ath79: port buffalo WZR-450HP2 from ar71xx 2024-12-23 22:52:37 +01:00
qca9558_comfast_cf-e380ac-v2.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_comfast_cf-wr650ac-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_comfast_cf-wr650ac-v2.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_comfast_cf-wr650ac.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_compex_wpj558-16m.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_devolo_dvl1xxx.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_devolo_dvl1200e.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_devolo_dvl1200i.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_devolo_dvl1750c.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_devolo_dvl1750e.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_devolo_dvl1750i.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_devolo_dvl1750x.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_dlink_dap-2680-a1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_dlink_dap-2695-a1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_dlink_dap-3662-a1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_dlink_dir-629-a1.dts ath79: add aliases to qca955x.dtsi for uart0/1 2024-03-08 17:35:01 +01:00
qca9558_domywifi_dw33d.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_elecom_wab-i1750-ps.dts ath79: register all ttys as Linux console for ELECOM WAB-I1750-PS 2024-03-24 21:10:59 +01:00
qca9558_engenius_dual_ap.dtsi ath79: add support for Senao Engenius ENS1750 2024-05-11 16:57:28 +02:00
qca9558_engenius_eap1750h.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_engenius_ecb1750.dts ath79: create common DTSI for ECB1200 and ECB1750 2020-12-22 19:11:50 +01:00
qca9558_engenius_ens1750.dts ath79: add support for Senao Engenius ENS1750 2024-05-11 16:57:28 +02:00
qca9558_engenius_epg5000.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_engenius_esr900.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_engenius_esr1750.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_engenius_ews660ap.dts ath79: add support for Senao Engenius ENS1750 2024-05-11 16:57:28 +02:00
qca9558_jjplus_jwap230.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
qca9558_librerouter_librerouter-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_linksys_ea4500-v3.dts ath79: linksys_ea4500-v3: take over the space for user data 2024-11-07 14:56:39 +01:00
qca9558_mikrotik_routerboard-92x.dtsi ath79: add aliases to qca955x.dtsi for uart0/1 2024-03-08 17:35:01 +01:00
qca9558_mikrotik_routerboard-96x.dtsi ath79: add aliases to qca955x.dtsi for uart0/1 2024-03-08 17:35:01 +01:00
qca9558_mikrotik_routerboard-911g-5hpacd.dts ath79: support MikroTik RouterBOARD 911G-5HPacD 2024-01-07 01:19:56 +01:00
qca9558_mikrotik_routerboard-921gs-5hpacd-15s.dts ath79: support MikroTik RouterBOARD 911G-5HPacD 2024-01-07 01:19:56 +01:00
qca9558_mikrotik_routerboard-922uags-5hpacd.dts ath79: support MikroTik RouterBOARD 911G-5HPacD 2024-01-07 01:19:56 +01:00
qca9558_mikrotik_routerboard-962uigs-5hact2hnt.dts ath79: add support for MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac) 2022-04-16 16:59:29 +02:00
qca9558_nec_aterm.dtsi ath79: remove dr_mode and vbus-supply 2025-01-08 14:55:28 +01:00
qca9558_nec_wg1400hp.dts ath79: add support for NEC Aterm WG1400HP 2024-10-19 17:56:46 +02:00
qca9558_nec_wg1800hp.dts ath79: add support for NEC Aterm WG1800HP 2024-10-19 17:56:46 +02:00
qca9558_nec_wg1800hp2.dts ath79: add support for NEC Aterm WG1800HP2 2024-10-19 17:56:46 +02:00
qca9558_netgear_ex7300.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_ocedo_koala.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_ocedo_ursus.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_openmesh_a40.dts ath79: Add support for OpenMesh A40 2021-06-05 01:17:11 +02:00
qca9558_openmesh_a60.dts ath79: Add support for OpenMesh A60 2021-06-05 01:17:11 +02:00
qca9558_openmesh_a60.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_openmesh_mr.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_openmesh_mr900-v1.dts ath79: convert ath10k calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9558_openmesh_mr900-v2.dts ath79: convert ath10k calibration data to NVMEM (binary MAC) 2024-02-01 17:09:02 +01:00
qca9558_openmesh_mr1750-v1.dts ath79: Add support for OpenMesh MR1750 v1 2021-01-19 21:41:26 +01:00
qca9558_openmesh_mr1750-v2.dts ath79: Add support for OpenMesh MR1750 v2 2021-01-19 21:41:26 +01:00
qca9558_openmesh_om5p-ac-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_openmesh_om5p-ac-v2.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_qxwlan_e558-v2-8m.dts ath79: add support for Qxwlan E558 v2 2020-10-17 20:17:59 +02:00
qca9558_qxwlan_e558-v2-16m.dts ath79: add support for Qxwlan E558 v2 2020-10-17 20:17:59 +02:00
qca9558_qxwlan_e558.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_sitecom_wlr-8100.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
qca9558_sophos_ap.dtsi ath79: remove dr_mode and vbus-supply 2025-01-08 14:55:28 +01:00
qca9558_sophos_ap55.dts ath79: remove dr_mode and vbus-supply 2025-01-08 14:55:28 +01:00
qca9558_sophos_ap55c.dts ath79: add support for Sophos AP100/AP55 family 2022-04-16 16:59:29 +02:00
qca9558_sophos_ap100.dts ath79: remove dr_mode and vbus-supply 2025-01-08 14:55:28 +01:00
qca9558_sophos_ap100c.dts ath79: add support for Sophos AP100/AP55 family 2022-04-16 16:59:29 +02:00
qca9558_tplink_archer-c.dtsi ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9558_tplink_archer-c5-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_tplink_archer-c7-v1.dts ath79: qca: remove mac-address-increment 2023-11-25 17:14:04 -08:00
qca9558_tplink_archer-c7-v2.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
qca9558_tplink_archer-d7-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_tplink_archer-d7.dtsi ath79: remove dr_mode and vbus-supply 2025-01-08 14:55:28 +01:00
qca9558_tplink_archer-d7b-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_tplink_re350k-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_tplink_re355-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9558_tplink_re450-v1.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9558_tplink_rex5x.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_tplink_tl-wdr4900-v2.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
qca9558_tplink_tl-wdr7500-v3.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_tplink_tl-wr941n-v7-cn.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_tplink_tl-wr1043nd-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9558_tplink_tl-wr1043nd-v3.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9558_tplink_tl-wr1043nd.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_tplink_tl-wr1045nd-v2.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9558_trendnet_tew-823dru.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9558_ubnt_nanobeam-ac-xc.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9558_ubnt_powerbeam-5ac-500.dts ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca9558_ubnt_rocket-5ac-lite.dts ath79: qca: convert to nvmem-layout 2023-11-25 17:14:04 -08:00
qca9558_watchguard_ap300.dts ath79: fix MAC address for senao loader devices 2024-06-14 21:05:19 +02:00
qca9558_zyxel_emg2926_q10a.dts treewide: rename ZyXEL to Zyxel 2024-08-25 15:08:25 +02:00
qca9558_zyxel_nbg6716.dts ath79: nbg6x16: use nvmem 2024-12-22 23:36:41 +01:00
qca9561_avm_fritz4020.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9561_nec_wf1200cr.dts ath79: nec,wX1200cr: use nvmem 2024-08-29 21:05:59 +02:00
qca9561_tplink_archer-c5x.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9561_tplink_archer-c6x.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9561_tplink_archer-c25-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9561_tplink_archer-c58-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9561_tplink_archer-c59-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9561_tplink_archer-c59-v2.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9561_tplink_archer-c60-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9561_tplink_archer-c60-v2.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9561_tplink_archer-c60-v3.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9561_tplink_eap225-wall-v2.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
qca9561_tplink_tl-wdr6500-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9561_xiaomi_mi-router-4q.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_asus_pl-ac56.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
qca9563_asus_rp-ac66.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
qca9563_comfast_cf-e375ac.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_compex_wpj563.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_dlink_covr-c1200-a1.dts ath79: add support for D-Link COVR-C1200 A1 2024-03-09 20:00:11 +01:00
qca9563_dlink_covr-p2500-a1.dts ath79: split dtsi for D-Link COVR-P2500 2024-03-09 20:00:11 +01:00
qca9563_dlink_covr.dtsi linux: replace nvmem-cells with nvmem-layout 2024-12-27 13:34:58 +01:00
qca9563_dlink_dap-1720-a1.dts linux: replace u-boot,env with nvmem,layout 2024-12-27 13:34:58 +01:00
qca9563_dlink_dir-8x9-a1.dtsi linux: replace u-boot,env with nvmem,layout 2024-12-27 13:34:58 +01:00
qca9563_dlink_dir-842-c.dtsi ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
qca9563_dlink_dir-842-c1.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9563_dlink_dir-842-c2.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9563_dlink_dir-842-c3.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9563_dlink_dir-859-a1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_dlink_dir-859-a3.dts ath79: drop redundant label with new LED color/function format 2024-02-07 14:48:34 +01:00
qca9563_dlink_dir-869-a1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_elecom_wrc-300ghbk2-i.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
qca9563_elecom_wrc-1750ghbk2-i.dts ath79: remove unused dts labels 2024-06-09 12:24:15 +02:00
qca9563_elecom_wrc-ghbk2-i.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_glinet_gl-ar750s-nor-nand.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_glinet_gl-ar750s-nor.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_glinet_gl-ar750s.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_glinet_gl-x1200-nor-nand.dts ath79: add support for GL.iNet GL-X1200 2023-02-25 14:31:42 +01:00
qca9563_glinet_gl-x1200-nor.dts ath79: add support for GL.iNet GL-X1200 2023-02-25 14:31:42 +01:00
qca9563_glinet_gl-x1200.dtsi ath79: remove wmac mac address defaults 2024-11-30 18:55:17 +01:00
qca9563_kuwfi_n650.dts ath79: add support for KuWFi N650 CPE 2024-11-30 18:52:41 +01:00
qca9563_nec_wg800hp.dts ath79: nec,wg800hp: convert to nvmem 2024-08-29 21:23:58 +02:00
qca9563_nec_wg1200cr.dts ath79: nec,wX1200cr: use nvmem 2024-08-29 21:05:59 +02:00
qca9563_netgear_wndr.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_netgear_wndr4300-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_netgear_wndr4500-v3.dts ath79: move usb led trigger node to SoC dtsi 2022-11-12 17:10:12 +01:00
qca9563_phicomm_k2t.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_qxwlan_e1700ac-v2-8m.dts ath79: add support for Qxwlan E1700AC v2 2020-10-17 20:18:00 +02:00
qca9563_qxwlan_e1700ac-v2-16m.dts ath79: add support for Qxwlan E1700AC v2 2020-10-17 20:18:00 +02:00
qca9563_qxwlan_e1700ac.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_rosinson_wr818.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_tplink_archer-a7-v5.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_tplink_archer-c2-v3.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_tplink_archer-c6-v2-us.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_tplink_archer-c6-v2.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_tplink_archer-c7-v4.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_tplink_archer-c7-v5.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_tplink_archer-x6-v2.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_tplink_archer-x7-v5.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_cpe710-v1.dts ath79: refactor dts of TP-Link CPE710-v1 2024-11-23 18:43:16 +01:00
qca9563_tplink_cpe710-v2.dts ath79: add support for TP-Link CPE710-v2 2024-11-23 18:43:20 +01:00
qca9563_tplink_cpe710.dtsi ath79: refactor dts of TP-Link CPE710-v1 2024-11-23 18:43:16 +01:00
qca9563_tplink_deco-m4r-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_tplink_deco-s4-v2.dts ath79: tplink,deco-s4-v2: use nvmem for cal 2024-12-18 20:27:03 +01:00
qca9563_tplink_eap2x5-1port.dtsi ath79: fix mac address on eap2x5-1port devices 2024-01-23 10:41:20 +01:00
qca9563_tplink_eap225-outdoor-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_eap225-outdoor-v3.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_eap225-v1.dts ath79: drop redundant label with new LED color/function format 2024-02-07 14:48:34 +01:00
qca9563_tplink_eap225-v3.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_eap225-v4.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_eap245-v1.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_eap245-v3.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_re450-v2.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_tplink_re450-v3.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_tplink_re450.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_re455-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_tplink_tl-wa1201-v2.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_tplink_tl-wpa8630-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_tplink_tl-wpa8630.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_tl-wpa8630p-v2-int.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_tplink_tl-wpa8630p-v2.0-eu.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_tplink_tl-wpa8630p-v2.1-eu.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_tplink_tl-wr1043n-v5.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_tplink_tl-wr1043n.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qca9563_tplink_tl-wr1043nd-v4.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_ubnt_amplifi-router-hd.dts linux: replace u-boot,env with nvmem,layout 2024-12-27 13:34:58 +01:00
qca9563_ubnt_uk-ultra.dts ath79: add support for UniFi UK-Ultra 2024-01-07 23:06:17 +01:00
qca9563_ubnt_unifiac-lite.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_ubnt_unifiac-lite.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_ubnt_unifiac-lr.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_ubnt_unifiac-mesh-pro.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_ubnt_unifiac-mesh.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_ubnt_unifiac-pro.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
qca9563_ubnt_unifiac-pro.dtsi ath79: drop phy-mask property 2022-06-15 20:07:26 +02:00
qca9563_ubnt_unifiac.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_xiaomi_aiot-ac2350.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_yuncore_a782.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9563_yuncore_xd3200.dts ath79: convert ath10k calibration data to NVMEM (built-in MAC) 2024-02-01 17:09:02 +01:00
qca9563_yuncore_xd4200.dts ath79: remove model name from LED labels 2020-10-02 13:51:39 +02:00
qca9563_yuncore_xd4200.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
qca9563_zte_mf28x.dtsi ath79: refactor ZTE MF28x dts files 2023-05-06 20:59:46 +02:00
qca9563_zte_mf281.dts ath79: drop redundant label with new LED color/function format 2024-02-07 14:48:34 +01:00
qca9563_zte_mf282.dts ath79: drop redundant label with new LED color/function format 2024-02-07 14:48:34 +01:00
qca9563_zte_mf286.dts ath79: ZTE MF286A: use specific board definition file for qca9888 2025-03-16 22:09:20 +01:00
qca9563_zte_mf286.dtsi ath79: refactor ZTE MF28x dts files 2023-05-06 20:59:46 +02:00
qca9563_zte_mf286a.dts ath79: support ZTE MF286A/R 2022-02-26 17:46:10 +01:00
qca9563_zte_mf286ar.dtsi ath79: ZTE MF286A: use specific board definition file for qca9888 2025-03-16 22:09:20 +01:00
qca9563_zte_mf286c.dts ath79: support ZTE MF286C 2025-03-16 22:10:04 +01:00
qca9563_zte_mf286r.dts ath79: support ZTE MF286A/R 2022-02-26 17:46:10 +01:00
qcn5502_asus.dtsi ath79: qcn: convert to nvmem-layout 2023-11-25 19:43:32 -08:00
qcn5502_asus_rt-ac59u-v2.dts ath79: add support for ASUS RT-AC59U / ZenWiFi CD6 2023-07-08 20:19:00 +02:00
qcn5502_asus_rt-ac59u.dts ath79: add support for ASUS RT-AC59U / ZenWiFi CD6 2023-07-08 20:19:00 +02:00
qcn5502_asus_rt-ac59u.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qcn5502_asus_zenwifi-cd6.dtsi ath79: add support for ASUS RT-AC59U / ZenWiFi CD6 2023-07-08 20:19:00 +02:00
qcn5502_asus_zenwifi-cd6n.dts ath79: add support for ASUS RT-AC59U / ZenWiFi CD6 2023-07-08 20:19:00 +02:00
qcn5502_asus_zenwifi-cd6r.dts ath79: add support for ASUS RT-AC59U / ZenWiFi CD6 2023-07-08 20:19:00 +02:00
qcn5502_netgear_ex7300-v2.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
qcn5502_tplink_archer-a9-v6.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
tp9343_tplink_tl-wa901nd-v4.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
tp9343_tplink_tl-wa901nd-v5.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
tp9343_tplink_tl-wa901nd.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
tp9343_tplink_tl-wr94x.dtsi ath79: add support for TP-Link TL-WA901ND v4 and v5 2020-05-18 13:35:38 +02:00
tp9343_tplink_tl-wr940n-v3.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
tp9343_tplink_tl-wr940n-v3.dtsi ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
tp9343_tplink_tl-wr940n-v4.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
tp9343_tplink_tl-wr940n-v6.dts ath79: convert to new LED color/function format where possible 2024-02-07 14:48:34 +01:00
tp9343_tplink_tl-wr941hp-v1.dts ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00
tp9343_tplink_tl-wr941nd-v6.dts ath79: move dts-v1 statement to ath79.dtsi 2020-09-25 23:26:34 +02:00
tp9343_tplink_tl-wx.dtsi ath79: mtd-cal-data removals 2024-06-09 12:24:15 +02:00