Jonas Jelonek 0c98150650 realtek: add support for Zyxel GS1920-24HPv2 ... Add support for V2 of Zyxel GS1920-24HP with 24 copper ports, 4 combo SFP/copper ports and PoE. Specifications: --------------- * SoC: Realtek RTL8391M * Flash: 32MiB Flash * RAM: 256MiB * Ethernet: 24x 10/100/1000 Mbps * SFP: 4 combo copper/SFP ports (via RTL8214FC) * PoE: 24x * Fan controller: ADT7468 * Serial: UART 3.3V TTL logic, 115200 8N1 * pinout (front to back): GND RX TX VCC * Buttons: 1x Reset, 1x Restore Notable differences to V1 (which require dedicated support): * "smaller" SoC (RTL8391M) * more RAM (256MiB vs 128MiB) * more Flash (32MiB vs 16MiB) + different layout * RTL8214FC uses different port numbers * SFP 25 and 26 use shared SCL * SFP 27 and 28 use different SDA * different monitoring IC (LM96000 vs ADT7468) * faster serial console by default * serial header easier accessible Note that the port LEDs do not work correctly yet due to missing LED configuration for RTL839X. Installation: ------------- (copied mostly as-is from 2a55846bf4) This device uses ZyNOS instead of Linux, this makes installation a bit more cumbersome. Serial console is required! 1. Set the switch to boot from the first image. This step is crucial, it will fail to boot if this is not set properly. 2. Connect to the switch using serial and interrupt the boot process to enter debug/recovery mode. 3. Load the OpenWrt initramfs image via XMODEM. You need to obtain an unlock code, based on your MAC address, first. See the excellent write up at https://www.ixo.de/info/zyxel_uclinux/ for details. Replace unlock_code in the commands below by the code obtained. The file length in bytes needs to be given instead of file_length below. You also need an XMODEM upload utility like "lrzsz-sx -X" to transfer the file. Start the XMODEM upload after running the ATUPxxxx command: > ATEN1,unlock_code > ATUP80100000,file_length > ATGO80100000 4. Wait for OpenWrt to boot. Once this is done, transfer the loader binary and the sysupgrade image to "/tmp" using scp. 5. Install OpenWrt permanently by running the following two commands on the switch (over SSH): > mtd write /tmp/loader.bin loader > mtd write /tmp/sysupgrade.bin firmware 6. Reboot the switch and enjoy OpenWrt. NB: You do not need to touch the loader binary unless it's recommended. The loader is not part of a regular sysupgrade file and will be left untouched. The boot loader only checks if the loader is valid to be able to boot. Recovery/ Return to stock: -------------------------- Just spam the "u" key during (or "z" for 9600 baud) during memory testing to trigger a recovery XMODEM upload at 115200 baud. A standard OEM upgrade image works properly. Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com> Link: https://github.com/openwrt/openwrt/pull/21944 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>		2026-02-13 23:33:25 +01:00
..
imagebuilder	treewide: drop CVS support	2026-02-13 15:40:13 +01:00
linux	realtek: add support for Zyxel GS1920-24HPv2	2026-02-13 23:33:25 +01:00
llvm-bpf
sdk	treewide: drop CVS support	2026-02-13 15:40:13 +01:00
toolchain
Config.in	targets: add USES_PM auto-feature	2025-07-20 12:16:13 +01:00
Makefile