The bus reset functions currently configure a lot of things. Looking
closely they have a topology setup and a polling setup part. Split the
big chunk in smaller better readable functions.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21906
Signed-off-by: Robert Marko <robimarko@gmail.com>
The downstream Realtek phy module is currently known as rtl83xx-phy.c
and its kernel config REALTEK_SOC_PHY. It has been simplified, cleaned
and now aligns to Realtek main module (upstream Realtek phy). It is no
longer tied to the Realtek switch SoC but serves as generic module for
1Gbit multiport phys. Adapt it as follows:
- place it into the realtek folder aside its upstream sibling
- rename it to realtek_multiport.c
- remove SoC dependency in Kconfig and Makefile
- change kernel configs for the targets accordingly
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21929
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop some lines that are not needed any longer.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21929
Signed-off-by: Robert Marko <robimarko@gmail.com>
RTL930x and RTL931x basically share the same logic for mac_config().
No need to duplicate that logic in two functions and to call one
from the other.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21895
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is still a stray call in setup_serdes to read the current CMU
band. The only effect is that the current band is printed to the log, the
value itself isn't used for anything further. Drop this since it's not
needed.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21858
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The function 'rtpcs_931x_sds_init_leq_dfe' was taken over mostly as-is
from the SDK. After looking at what it actually does (by seeing which
register are written and how they are used elsewhere), it becomes clear
that 'init' isn't the correct term to describe what it does. It sets the
LEQ and DFE parameters to baseline values (mostly 0) and turns off auto
mode, switching to manual LEQ/DFE and forcing those baseline values.
This is rather a reset to a known state instead of an initialization.
Name the function accordingly.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21858
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add some comments to several register writes explaining what these
fields are. The information was extracted from the SDK. This allows to
understand much better what's going on there.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21858
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, the CMU is configured after media specific settings have been
set. This seems to work however does not make that much sense. The
proper clock should be configured before the TX/RX channels are
configured. Thus, move the call to the CMU configuration above the media
handling.
While at it, handle the return code of the CMU config properly.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21858
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The SerDes setup for RTL931x relies on chip specifics in some cases,
Determining both usually requires some register operations. But we can
avoid to do this every time again and again since the information is
static anyway. Thus, move this to initialization for RTL93xx, only read
once and store it in the global control structure. Though not used for
RTL930x, it has the same registers and information.
While at it, give referenced defines a proper prefix.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21858
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
From the Realtek SDK we know that the chip type tell us whether a chip
is a normal chip or an engineering sample/testchip [1]. Such engineering
samples likely never reach any consumer device, only some initial
development boards. So far we haven't encountered any device with that,
thus the code paths handling this are practically dead and can hardly be
checked of they work properly. To focus on support for the devices we
actually have, drop support for such engineering samples/testchips. This
may be readded later if there's sufficient need for this.
[1] 3261cf2e61/sources/rtk-dms1250/system/drv/swcore/chip_probe.c (L345)
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21858
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Drop a register write sequence from the USXGMII setup for RTL931x in
favor of using a function that is already present. From the name, the
function initializes LEQ DFE. Though it's not yet clear what it exactly
does, this is already better then having a sequence with no explanation
somewhere in the code.
Apparently, when this code was added, the function wasn't present
but it's content was just added here as single usage.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21858
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport the PSE-PD (Power Sourcing Equipment - Powered Device)
framework updates from Linux 6.13 through 6.19. This brings modern
PoE (Power over Ethernet) controller support to OpenWrt, enabling
userspace control of PSE hardware via ethtool.
Key features:
- Enhanced ethtool integration for PSE status and configuration
- Power domain support with budget evaluation strategies
- PSE event reporting via netlink
- Port priority management for power budget allocation
- New Si3474 PSE controller driver
Backported commits:
v6.13 core framework and TPS23881 improvements:
- 6e56a6d47a7f net: pse-pd: Add power limit check
- 0b567519d115 net: pse-pd: tps23881: Simplify function returns
- 4c2bab507eb7 net: pse-pd: tps23881: Use helpers to calculate bit offset
- f3cb3c7bea0c net: pse-pd: tps23881: Add missing configuration register
- 3e9dbfec4998 net: pse-pd: Split ethtool_get_status
into multiple callbacks
- 4640a1f0d8f2 net: pse-pd: Remove is_enabled callback from drivers
- 7f076ce3f173 net: pse-pd: tps23881: Add power limit
and measurement features
- 10276f3e1c7e net: pse-pd: Fix missing PI of_node description
- 5385f1e1923c net: pse-pd: Clean ethtool header of PSE structures
v6.17 power domains and event support:
- fa2f0454174c net: pse-pd: Introduce attached_phydev to pse control
- fc0e6db30941 net: pse-pd: Add support for reporting events
- f5e7aecaa4ef net: pse-pd: tps23881: Add support for PSE events
- 50f8b341d268 net: pse-pd: Add support for PSE power domains
- 1176978ed851 net: ethtool: Add support for power domains index
- c394e757dedd net: pse-pd: Add helper to report hw enable status
- ffef61d6d273 net: pse-pd: Add support for budget evaluation strategies
- 359754013e6a net: pse-pd: pd692x0: Add PSE PI priority feature
- 24a4e3a05dd0 net: pse-pd: pd692x0: Add controller and manager power
- 56cfc97635e9 net: pse-pd: tps23881: Add static port priority feature
- d12b3dc10609 net: pse-pd: pd692x0: reduce stack usage
v6.18 Si3474 driver and fixes:
- 1c67f9c54cdc net: pse-pd: pd692x0: Fix power budget leak
- 7ef353879f71 net: pse-pd: pd692x0: Skip power budget when undefined
- a2317231df4b net: pse-pd: Add Si3474 PSE controller driver
v6.19 maintenance and TPS23881B support:
- 2c95a756e0cf net: pse-pd: tps23881: Fix current measurement scaling
- f197902cd21a net: pse-pd: pd692x0: Replace __free macro
- 6fa1f8b64a47 net: pse-pd: pd692x0: Separate configuration parsing
- 8f3d044b34fe net: pse-pd: pd692x0: Preserve PSE configuration
- 4d07797faaa1 net: pse-pd: tps23881: Add support for TPS23881B
Signed-off-by: Carlo Szelinsky <github@szelinsky.de>
Link: https://github.com/openwrt/openwrt/pull/21810
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add board support for the Xikestor SKS8300-12E2T2X switch.
Hardware specifications:
========================
-Realtek RTL9302C SoC, 1x MIPS-34Kc, 800 MHz
-512 MB DDR3 RAM
-32 MB SPI-NOR Flash
-12x 2.5GBASE-T Ports (RTL8224)
-2x 10GBASE-T Ports (RTL8261)
-2x 10G SPF+ Ports
-Reset Button on the front panel
-Power & SYS LED's
-UART (115200 8N1) via RJ45
Flash instruction:
==================
-Prepare TFTP server & connect to serial port
-Connect your computer to one of the RJ45 ports
-Power on and interrupt autoboot with Shift + A.
-Use Shift + Q to drop from vendor CLI to U-Boot CLI.
-Change U-Boot Bootcommand (needed for network functionality):
> setenv bootcmd 'rtk network on; boota'
> saveenv
-Start network:
> rtk network on
-Set switch IP and TFTP server IP:
> setenv ipaddr [IP-ADDRESS]
> setenv serverip [IP-ADDRESS]
-Load initramfs image from TFTP server:
> tftpboot 0x82000000 [IMAGEFILE]
-Boot with the downloaded image:
> bootm 0x82000000
-Backup the stock firmware if needed
-Perform sysupgrade with the sysupgrade image (in Luci or Terminal via scp & sysupgrade)
Back to stock firmware:
=======================
-In the Terminal enter:
> fw_setenv bootcmd 'boota'
-Write firmware with:
> sysupgrade -F [IMAGEFILE]
Signed-off-by: Michael Wagenhofer <michael@wagenhofer.de>
Link: https://github.com/openwrt/openwrt/pull/21773
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Looking at the Realtek mdio busses there are curently the following
root@OpenWrt:~# mdio
1b000000.switchcore:mdio-controller-mii
fixed-0
realtek-aux-mdio
realtek-serdes-mdio
rtldsa_mdio-0
The main mdio bus for the phys is named after the dts node it belongs
to (1b000000.switchcore:mdio-controller-mii). As it is attached to the
controller node it is even more confusing.
Align the naming to the other busses and use "realtek-mdio".
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21702
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The phy driver still uses the ancient unknown firmware file format
for the internal RTL8218B of the RTL838x. Get rid of that and
convert the initialization to the bare minimum.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21885
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Enabling and disabling in-band auto-negotation is already supported on
RTL93xx. However, so far the advertisement is left unchanged at the
default of 0x1a0 (full duplex + pause + asymmetric pause).
Instead, set the advertisement to reflect the current configuration for
1000Base-X and 2500Base-X. Nothing needs to be done for SGMII, as the
advertisement register is ignored in that case.
Testing shows that negotiation of flow control works for 1000Base-X and
2500Base-X (tested with RTL930x on both ends of the link).
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/21869
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a new SerDes operation for restarting in-band negotiation including
an implemenation for RTL93xx, and call it from .pcs_an_restart.
This is a prerequisite for configuration of the in-band advertisement,
as changing it requires triggering a restart of auto-negotiation.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/21869
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit 78bf3a5f44 ("realtek: dsa: Fix rate control initialization") enabled
code setting up the "storm control" feature. This casued a speed regression
on rtl838x, reducing the effective max speed per port from line rate to around
500 Mbits/s.
Storm control is a policy feature with a number of input parameters depending
on use case and environment. It is not possible to define a meaningful static
policy in the driver. The problem isn't just the arbitrary limits in the
current code. Such features require userspace interfaces.
Drop this code for now. It wasn't missed while it was disabled.
Cc: Sven Eckelmann <se@simonwunderlich.de>
Fixes: 78bf3a5f44 ("realtek: dsa: Fix rate control initialization")
Link: https://github.com/openwrt/openwrt/issues/21692
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://github.com/openwrt/openwrt/pull/21877
Signed-off-by: Robert Marko <robimarko@gmail.com>
DSA tagging currently works with a tuned trailer tagging. That means:
- realtek target uses tag_trailer for tagging
- there is a patch for the trailer tagger to write the target port not
as a bitfield but as an integer
Make the tagging independent from upstream and hacky patches by providing
a new downstream driver. This can be aligned easier for future development.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21815
Signed-off-by: Robert Marko <robimarko@gmail.com>
The SoC specific configuration structure is currently manually
assigned depending on the family_id. This will be removed in
the future. Make use of device_get_match_data() instead.
While we are here rename the structure prefix.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21866
Signed-off-by: Robert Marko <robimarko@gmail.com>
Bit 15 of the rtl838x SMI_GLB_CTRL register is set early during mdio reset
and never cleared. There is no need to set it again.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://github.com/openwrt/openwrt/pull/21868
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit 17f12695d0 ("realtek: mdio: rtl838x: activate combo PHY media detection")
dropped setting bit 15 of the SMI_GLB_CTRL register without any explanation. This
broke the Netgear GS108Tv3, causing phy patching to fail:
Firmware loaded. Size 1184, magic: 83808380
Realtek RTL8218B (internal) 1b000000.switchcore:mdio-controller-mii:08: patch
Realtek RTL8218B (internal) 1b000000.switchcore:mdio-controller-mii:08: package not ready for patch.
Realtek RTL8218B (internal) 1b000000.switchcore:mdio-controller-mii:0f: probe with driver Realtek RTL8218B (internal) failed with error -5
None of the internal phys was able to detect a link after this error.
Some rtl8380 devices, like the Zyxel GS1900-10HP A1, were not affected by the bug
because their boot loader always sets bit 15. The bug could also be worked around
on affected devices by running "rtk network on" before booting OpenWrt, setting
bit 15 as a side effect.
Cc: Markus Stockhausen <markus.stockhausen@gmx.de>
Cc: Robert Marko <robimarko@gmail.com>
Fixes: 17f12695d0 ("realtek: mdio: rtl838x: activate combo PHY media detection")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://github.com/openwrt/openwrt/pull/21868
Signed-off-by: Robert Marko <robimarko@gmail.com>
The internal RTL8218B gets detected cleanly. No need for
additional checks of the bus address or the SoC type.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21857
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add everything that's needed to have a standalone setup of the XSGMII
mode without having to rely on previous U-boot setup. This includes
patch sequences for the SerDes and extensions of symbol error reset and
reading.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21762
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The XSGMII mode is special in several regards. The inband
autonegotiation for this mode is called 'XSG N-way'. It is controlled
using different bits and location, and using XSG operations.
Add support for this by enhancing the set_autoneg implementation shared
by RTL930x and RTL931x. This can stay shared since it works the same for
both variants.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21762
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of having all kinds of SerDes-related operations in the global
pcs config structure, there's now a SerDes ops structure which is
intended to cover and separate this.
Move the set_autoneg hook to the SerDes ops to adhere to this desired
separation. Calling the operation is further encapsulated with a small
convenience helper.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21762
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This header is deprecated and typically platform_device.h should be
used.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21164
[Adapted the lantiq patches a bit]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not derive the number of hardware receive rings from the SoC
family. Instead add the information to the configuration
structure. Make use of it during ethernet driver probing.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21706
Signed-off-by: Robert Marko <robimarko@gmail.com>
For packets trapped to the CPU for a special reason (not normal
forward), the RTL931x tag decoding always print a log message with level
INFO. This is not needed and just spams the log, e.g. when LLDP packets
are running through the network, each of them causes a log message.
Make that a debug message instead of an info message. We can keep it,
just change when it's printed.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21844
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove the unneeded sw_xxx() macros.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21824
Signed-off-by: Robert Marko <robimarko@gmail.com>
Make use of regmap in the RTL93xx reset functions.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21824
Signed-off-by: Robert Marko <robimarko@gmail.com>
Make use of regmap in RTL83xx reset functions.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21824
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some straight forward conversion ...
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21824
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop legacy sw_xxx() macros for RTL931x devices. While we are here
reorganize the access and avoid masked access where possible. So the
code is easier to read.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21824
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop legacy sw_xxx() macros for RTL930x devices. While we are here
reorganize the access and avoid masked access where possible. So the
code is easier to read.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21824
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop legacy sw_xxx() macros for RTL839x devices. While we are here
reorganize the access and avoid masked access where possible. So the
code is easier to read.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21824
Signed-off-by: Robert Marko <robimarko@gmail.com>
Increase readability by replacing more numbers and bit operations
with macros in order to give them distinct, expressive names.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Link: https://github.com/openwrt/openwrt/pull/21786
Signed-off-by: Robert Marko <robimarko@gmail.com>
So far the function prefix rtl83xx_ is used for functions which are
exclusive to RTL8390_FAMILY_ID but also for ones shared between
RTL8390_FAMILY_ID/RTL9300_FAMILY_ID/RTL9310_FAMILY_ID.
For a more fitting, precise use of rtl83xx_ rename the ones in dsa.c
which are also used by RTL9300_FAMILY_ID and RTL9310_FAMILY_ID
to rtldsa_.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Link: https://github.com/openwrt/openwrt/pull/21786
Signed-off-by: Robert Marko <robimarko@gmail.com>
For the IPv4 unknown multicast flood portmask the first byte should be
for the higher port numbers and the following byte for the lower port
numbers, just like for the L2 unknown multicast flood portmask or the
IPv6 unknown multicast flood portmasks, too. Not the other way around.
Fix the debug output here by adjusting the offsets accordingly.
Fixes: 27029277f9 ("realtek: add switch driver support for the RTL93XX based switches")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Link: https://github.com/openwrt/openwrt/pull/21786
Signed-off-by: Robert Marko <robimarko@gmail.com>
Avoid to reconfigure a SerDes when it has been configured for a mode
before. This usually applies to switches which drive multiple ports on a
single SerDes. For those, the phylink subsystem triggers PCS
configuration everytime although it's a single SerDes. For example, on
switches with XSGMII-connected RTL8218D the particular SerDes is
configured eight times but only a single run is needed.
Add a proper check to pcs_config which checks the mode stored in the
SerDes instance against the requested mode. Other 'settings' should be
executed though, e.g. setting autoneg. While at it, drop the check if
there is a 'setup_serdes' implementation. It's just a driver-internal
interface and all variants implement this now.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21763
Signed-off-by: Robert Marko <robimarko@gmail.com>
All variant-specific setup_serdes functions currently make equal use of
the mapping from the interface mode to the hardware mode. To reduce
redundancy, move this mapping to the generic pcs_config, from where the
setup_serdes implementations are called.
This includes slightly changing the setup_serdes signature and some
debug messages.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21763
Signed-off-by: Robert Marko <robimarko@gmail.com>
The linux kernel printk has a MAC address specifier `%pM` that can be
used to pretty-print MAC addresses. We should use this specifier when
printing MAC addresses for humans since that ensure the appearance that
people are used to.
Fixes#21796
Signed-off-by: Bevan Weiss <bevan.weiss@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21812
Signed-off-by: Robert Marko <robimarko@gmail.com>
"features" describes the currently active device options and
"hw_features" describes all possible ones. So hw_features must
be a superset of features. Fix that.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21778
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove all old structures and defines that are no longer needed.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21778
Signed-off-by: Robert Marko <robimarko@gmail.com>
Provide a new transmit function. It is cleaner and closer to
upstream than what we have now. The basic features are:
- Avoid memory moving and keep data in the SKBs
- Only protect really critcal parts by a lock as transmit
queues will be only called once by the kernel
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21778
Signed-off-by: Robert Marko <robimarko@gmail.com>
The operating system has enough features to control the transmit
queues. There is no need to provide a hard coded distribution
function. Especially differentiating between a round robin for
RTL83xx and high/low priority for RTL93xx makes no sense. All
devices have the same low/high priority queues.
Simply present two "generic" queues to the kernel.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21778
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ethernet driver will get a new transmit function. As a first
step add the required structures and initialize them.
To get an idea: In the future the transmit buffer will hold only
the needed packet header information. The real data is kept in the
SKBs. So only pointers will be changed and memory moving can be
avoided. The SoC will transfer packet data directly from the SKBs.
Additionally a new transmit lock will be established that is
separated from the current driver lock. This is only needed
to guard the "kick-the-engine" command. So contention of the old
global lock can be reduced.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21778
Signed-off-by: Robert Marko <robimarko@gmail.com>
Ethernet transmit handling processes data synchronously via a
packet buffer. As soon as it kicks the SoC to send the packet
no more post processing is needed. Especially there is no need
for transmit completion interrupts. Disable them to reduce the
CPU load.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21778
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop legacy sw_xxx() macros for rtl838x devices. While we are here
reorganize the access and aovid masked access where possible. So the
code is easier to read.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/21741
Signed-off-by: Robert Marko <robimarko@gmail.com>
