forked from mirror/openwrt
14 commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
INAGAKI Hiroshi
|
70b5252265 |
uboot-envtools: ipq50xx: add support for ELECOM WRC-X3000GS2
Add support for ELECOM WRC-X3000GS2 to update "bootdelay" variable configured as "0" by default when sysupgrade. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Link: https://github.com/openwrt/openwrt/pull/18543 Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
|
jonathan brophy
|
8da24b1109 |
Qualcommax: IPQ807x: Add support for TP-Link Deco X80-5G
The TP-link Deco X80-5G is a AX WIFI router with a single 1G (LAN) and 1 2.5G (WAN) port with a built in Quectel 5G modem. Specifications: Architecture ARMv8-A (aarch64 Cortex A53, 4 cores) Vendor Qualcomm Bootloader U-Boot (2016) System-On-Chip Qualcomm IPQ8074A (Networking Pro 1210 platform) CPU/Speed 2.2GHZ Flash-Chip ESMT F59D1G81MB-45TI 1G-bit NAND Flash MB 128MB (1Gbit) RAM-chip 2* ESMT M15T4G16256A-DEBG2G 2Gb DDR3L (32bit) RAM MB 512MB (4Gbit) WLan System-On-Chip (5g) Qualcomm QCN5054 WLan Front end modules (5g) 8* Qorvo QPF4588 WLAN (5G) A/N/AC/AX WLAN Antenna (int) 8* (4 shared with 2.5G) WLan System-On-Chip (2.4G) Qualcomm QCN5024 WLan Front end modules (2.4G) 4* Skyworks SKY85340-11 WLAN (2.4G) B/G/N/AX WLAN Antenna (int) 4* (shared with 5g) Eithernet-phy (1Gbit) Qualcomm (Atheros) AR8033-AL1A Ethernet (1Gbit) 1* Eithernet-phy (2.5Gbit) Qualcomm QCA8081 Ethernet (2.5Gbit) 1* Switch Embedded in the SOC? Serial 1.8v 8n1 (testpoints) Modem System-On-Chip Qualcomm 5G RG50xQ (Snapdragon X55 platform) 5G modem capability 5000Mbps down 900Mbps up 5G modem bands N1/N3/N5/N7/N8/N20/N28/N38/N40/N41/N77/N78/N79 4G modem capability 4.5G LTE-Advanced Pro (Cat20 down 2Gbps) (Cat18 up 200Mbps) 4G modem FDD bands B1/B3/B5/B7/B8/B18/B19/B20/B26/B28 4G modem TDD bands B34/B38/B39/B40/B41/B42/B43 Modem antenna (int) 8* (5G/4G use) Modem antenna (ext) 2* SMA connectors (5G/4G use) SIM type 1* Nano SIM Telephony 1* POTS RJ11 (see wiki for more info:) https://openwrt.org/inbox/toh/tp-link/x80-5g_v1 Notes: Installation Instructions: Between antennas 7 and 8 on the PCB with the RGB harness there are three test pads labelled TP1 TP2 and TP3 connections are as follows: |TP2|-- RX |TP1|-- TX |TP3|-- GND RX requires an external pullup to operate somewhere around 5 K ohm but your luck may vary the Uart is 1.8v Set a static IP and set up a tftpserver and terminal. power the router and quickly type the magic string “tpl” and press enter to break into u-boot in the shell set the environment variables to enable tftp booting setenv ipaddr (routerIP) setenv serverip (server IP) load you initramfs: tftpboot 0x44000000 (serverIP):openwrt-qualcommax-ipq807x-tplink_x80-5g-initramfs-uImage.itb boot your initramfs bootm upload your factory image to /tmp format and install the factory image: ubiformat /dev/mtd12 -y -f /tmp/openwrt-qualcommax-ipq807x-tplink_x80-5g-squashfs-factory.ubi Note as this device swaps root partitions upon update your boot partition may be set as mtd13 Update script to mount factory tplink partition's for MAC recovery and device data. Capture Labelmac from Factory_data partition. Patch LAN from Labelmac. Patch ART from Labelmac. Set GPIO to make modem operational from boot. GPIO fan tables work like the stock device with three fan maps high active idle with a top fan speed of 6800 RPM. High temp 70 deg speeds 6-8 Active temp 50 deg speeds 2-5 low temp 25 degree speed 0-1 Signed-off-by: jonathan brophy <professor_jonny@hotmail.com> Link: https://github.com/openwrt/openwrt/pull/16329 Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
|
Olgun Demir
|
c3b8108a2b |
ramips: Add support for Xiaomi MiWiFi 3A
The Xiaomi MiWiFi 3A wireless router has a similar system architecture as the Xiaomi Mi 4A router, which is already officially supported by OpenWrt. Product website: https://www.mi.com/miwifi3a Device specification -------------------- SoC: MT7628AN MIPS_24KEc @ 580 MHz 2.4G-bgn 2x2 WiFi: MT7612EN 5G-an, ac 80 MHz 2T2R Flash: 16 MB DRAM: 64 MB Switch: MT7628AN (integrated in SoC) Ethernet: 1 x 10 /100 Mbps USB: None Antennas: 2 x 2,4 GHz and 2 x 5 GHz (all are external and non-detachable) LEDs: blue/red/amber Buttons: Reset Serial: 115200,8n1 MAC addresses as verified by OEM firmware: ------------------------------------------ use address source LAN *:DD factory 0x28 WAN *:DD factory 0x28 2g *:DE factory 0x4 5g *:DF factory 0x8004 OEM firmware uses VLAN's to create the network interface for WAN and LAN. Bootloader info: ---------------- The stock bootloader uses a "Dual ROM Partition System". OS1 is a deep copy of OS2. The bootloader starts OS2 by default. To force start OS1 it is needed to set "flag_try_sys2_failed=1". How to install: --------------- 1- Use OpenWRTInvasion to gain Telnet, SSH and FTP access: https://github.com/acecilia/OpenWRTInvasion [IP: 192.168.31.1 | Username: root | Password: root | FTP-Port: 21] 2- Connect to router using telnet or ssh. 3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0". Copy /tmp/mtd0 to computer using ftp. 4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3a-squashfs-sysupgrade.bin to /tmp in router using ftp. 5- Enable UART access and change start image to OS1. nvram set uart_en=1 nvram set flag_last_success=1 nvram set boot_wait=on nvram set flag_try_sys2_failed=1 nvram commit 6- Erase OS1 & OS2 and install OpenWrt mtd erase OS1 mtd erase OS2 mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3a-squashfs-sysupgrade.bin OS1 Credits: -------- This PR is based on the work of Zehao Zhang (Github: @ZZH-Finalize) that he had published in the PR: #15698 Signed-off-by: Olgun Demir <olgun.demir@mail.com.tr> Link: https://github.com/openwrt/openwrt/pull/18427 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> |
||
|
Scott Mercer
|
3307fe8ee4 |
qualcommax: ipq50xx: add support for GL.iNET GL-B3000
Add support for GL.iNET (AX3000) B3000.
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Winbond W634GU6NQB-11 (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
* Wi-Fi: QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (3 Ports 10/100/1000 GBASE-T)
* Flash: Winbond W25N01GWZEIG (128 MiB)
* LEDs: 1x single-color blue LED (GPIO 24 Active High)
1x single-color white LED (GPIO 23 Active High)
* Buttons: 1x Reset (GPIO 27 Active Low)
Flash Instructions:
*** The .img files are now universal ! ***
Openwrt --> openwrt-qualcommax-ipq50xx-glinet_gl-b3000-squashfs-factory.img
GL.iNet OEM --> openwrt-b3000-4.5.18-0731-1722397535.img
Either file can be flashed, in any of the available upgrade options, in both Firmwares.
Pick a file .. pick a method .. and SEND IT !!
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17903
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
||
|
Schneider Azima
|
7921e48d43 |
mediatek: add support for Mercusys MR80X v3
This commit adds support for Mercusys MR80X(EU) v3 router. Device specification: - SoC: Mediatek MT7981b, Cortex-A53, 64-bit - RAM: 512MB - Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB) - Ethernet: 4x 100/1000 Mbps LAN1,LAN2,LAN3 & WAN - Wireless: 2.4GHz (802.11 b/g/n/ax) - Wireless: 5GHz (802.11 a/n/ac/ax) - LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled LEDs on ethernet ports - Buttons: 1 (Reset) - Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI slots contain "seconduboot" (also U-Boot 2022.01-rc4) Installation (UART): - Place OpenWrt initramfs-kernel image on tftp server with IP 192.168.1.2 - Attach UART, switch on the router and interrupt the boot process by pressing 'Ctrl-C'. - Set the uboot environment for startup. setenv tp_boot_idx 0; setenv bootcmd bootm 0x46000000; saveenv If the bootarg is set to boot from ubi1, also change it to ubi0. - Load and run OpenWrt initramfs image. setenv serverip 192.168.1.2; setenv ipaddr 192.168.1.1; tftpboot initramfs-kernel.bin; bootm - Browse IP 192.168.1.1, upload the 'sysupgrade' image and do upgrade. Recovery: - Press Reset button and power on the router. - Navigate to U-Boot recovery web server (http://192.168.1.1/) and upload the OEM firmware. Stock layout: 0x000000000000-0x000000200000 : "boot" 0x000000200000-0x000000300000 : "u-boot-env" 0x000000300000-0x000003500000 : "ubi0" 0x000003500000-0x000006700000 : "ubi1" 0x000006700000-0x000006f00000 : "userconfig" 0x000006f00000-0x000007300000 : "tp_data" ubi0/ubi1 format: U-Boot at boot checks that all volumes are in place: +-------------------------------+ | Volume Name: uboot Vol ID: 0| | Volume Name: kernel Vol ID: 1| | Volume Name: rootfs Vol ID: 2| +-------------------------------+ MAC addresses: +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | label | 94:0C:xx:xx:xx:12 | label | | WAN | 94:0C:xx:xx:xx:13 | label+1 | | LAN | 94:0C:xx:xx:xx:12 | label | | WLAN 2g | 94:0C:xx:xx:xx:11 | label-1 | | WLAN 5g | 94:0C:xx:xx:xx:10 | label-2 | +---------+-------------------+-----------+ label MAC address was found in UBI partition "tp_data", file "default-mac". Signed-off-by: Schneider Azima <Schneider-Azima12@protonmail.com> Link: https://github.com/openwrt/openwrt/pull/18181 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> |
||
|
Yujie Zhu
|
db3eff1022 |
mediatek: filogic: add Netcore N60 Pro support
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: M16U4G16256A DDR4 512MB
Ethernet: 2x 2.5G + 3x 1G
USB: 1x USB 3.0
WiFi1: MT7975N 2.4GHz 4T4R
WiFi2: MT7975PN 5GHz 4T4R
Button: Reset, WPS
Power: DC 12V 2A
Flash instructions:
Connect to the router using ssh or telnet,
username: useradmin, password is the web
login password of the router.
Use scp to upload bl31-uboot.fip and flash:
"mtd write xxx-bl31-uboot.fip FIP"
"mtd erase ubi"
Connect to the router via the Lan port,
set a static ip of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
Download initramfs image, reboot router,
waiting for tftp recovery to complete.
After openwrt boots up, perform sysupgrade.
Note:
Back up all mtd partitions before flashing.
Signed-off-by: Yujie Zhu <libriunc@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18138
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
||
|
Yang Xiwen
|
5dbf93c8c5 |
ipq60xx: add support for TP-Link EAP623-Outdoor HD v1
Specifications: * SoC: Qualcomm IPQ6018 (64-bit Quad-core Arm Cortex-A53 @ 1800MHz) * Memory: 1 GiB * Serial Port: 3v3 TTL 115200n8 * Wi-Fi: QCN9074 (4x4 5 GHz 802.11ax) * Wi-Fi: IPQ6018 (4x4 2.4 GHz 802.11b/g/n/ax) * Ethernet: RTL8211F (10/100/1GBASE-T) * Flash: ESMT F59D1G81MB (128 MiB) * LEDs: 1x Green Status (GPIO 37 Active High), 1x Yellow Status (GPIO 32 Active High) and an LED global control GPIO (GPIO 36 Active High, set up by U-Boot) * Buttons: 1x Reset (GPIO 9 Active Low) Installation Instructions (Serial+TFTP): 1. Solder 4 pin header to the pads near T32 and T31. 2. Connect 3V3 TTL port to TX, RX, and GND, which are pad T31, T32 and the pad near T31 respectively. Be sure not to connect VCC and crossover TX and RX. 3. Copy RAM firmware image openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb to TFTP server root, available at 192.168.0.1. 4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the serial console (115200 baud) until autoboot is halted. 5. Run the following commands in the U-boot prompt: # setenv serverip 192.168.0.1 # setenv ipaddr 192.168.0.99 # tftpboot 0x44000000 openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb # bootm You may need to type Ctrl+C and Enter before running these commands to clear invisible characters from the buffer. 6. Run the following command in a terminal to copy the sysupgrade image to be installed (check IP address): $ scp openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/ 7. Activate the OpenWrt serial console and run the following commands: # cd /tmp # sysupgrade -n openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin 8. The AP will reboot and OpenWrt will be successfully installed. Signed-off-by: Yang Xiwen <forbidden405@outlook.com> Link: https://github.com/openwrt/openwrt/pull/18389 Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
|
Mikhail Zhilkin
|
d8002cb627 |
mediatek: add support for netis NX31
This PR adds support for netis NX31 router.
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM : 256 MiB DDR3
- Flash : SPI-NAND 128 MiB (ESMT)
- WLAN : MediaTek MT7976CN dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x3 (LAN, MediaTek MT7531AE)
10/100/1000 Mbps x1 (WAN, SoC internal phy)
- USB : No
- Buttons : Mesh, Reset
- LEDs : 1x Power (blue), unmanaged
1x Status (blue), gpio-controlled
1x WiFi 2.4 GHz (blue), gpio-controlled
1x WiFi 5 GHz (blue), gpio-controlled
3x LAN activity (blue), switch-controlled
1x WAN activity (blue), gpio-controlled
- Power : 12 VDC, 1 A
Installation
------------
1. Connect to the router using ssh (user: admin, pass: web interface
password)
2. Make mtd backup:
cat /dev/mtd0 | gzip -1 -c > /tmp/mtd0_spi0.0.bin.gz
cat /dev/mtd1 | gzip -1 -c > /tmp/mtd1_BL2.bin.gz
cat /dev/mtd2 | gzip -1 -c > /tmp/mtd2_u-boot-env.bin.gz
cat /dev/mtd3 | gzip -1 -c > /tmp/mtd3_Factory.bin.gz
cat /dev/mtd4 | gzip -1 -c > /tmp/mtd4_FIP.bin.gz
cat /dev/mtd5 | gzip -1 -c > /tmp/mtd5_ubi.bin.gz
3. Download mtd backup from the /tmp dir of the router to your PC using
scp protocol
4. Upload OpenWrt 'bl31-uboot.fip', 'preloader.bin' images to the /tmp
dir of the router using scp protocol
5. Write FIP and BL2 (replace bootloader):
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-bl31-uboot.fip FIP
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-preloader.bin BL2
6. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
7. Erase 'ubi' partition and reboot the router:
mtd erase ubi
reboot
8. U-Boot automatically boot OpenWrt recovery image from tftp server to
the RAM
9. Upload OpenWrt 'sysupgrade.itb' image to the /tmp dir of the router
(IP: 192.168.1.1) using scp protocol
10. Connect to the router using ssh and run:
sysupgrade -n openwrt-mediatek-filogic-netis_nx31-squashfs-sysupgrade.itb
Return to stock
---------------
1. Unpack stock BL2 and FIP partitions backup
2. Upload stock BL2 and FIP partitions backup to the /tmp dir of the
router using scp protocol
3. Connect to the router using ssh and run:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd unlock FIP
4. Restore backup:
mtd write /tmp/mtd4_FIP.bin FIP
mtd write /tmp/mtd1_BL2.bin BL2
5. Erase ubi and reboot:
mtd erase ubi
reboot
6. Power off the router
7. Press Reset button and power on the router. Release the button after
~10 sec
8. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware
Recovery
--------
1. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
2. Press “Reset” button and power on the router. After ~10 sec release
the button.
3. Use OpenWrt initramfs system for recovery
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | dc:xx:xx:d1:xx:18 | label |
| WAN | dc:xx:xx:d1:xx:1a | label+2 |
| WLAN 2g | de:xx:xx:11:xx:19 | |
| WLAN 5g | de:xx:xx:71:xx:19 | |
+---------+-------------------+-----------+
The LAN MAC was found in 'Factory', 0x1fef20
The WAN MAC was found in 'Factory', 0x1fef26
The WLAN 2g/5g MAC prototype was found in 'Factory', 0x4
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18324
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
||
|
Fil Dunsky
|
99ea96c297 |
mediatek: filogic: add support for Huasifei WH3000
**Huasifei WH3000 eMMC / Fudy MT3000** Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC. MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ **Specifications** SoC: Filogic 820 MT7981A (1.3GHz) RAM: DDR4 1GB Flash: eMMC 8GB WiFi: 2.4GHz and 5GHz with 3 antennas Ethernet: 1x WAN (10/100/1000M) 1x LAN (10/100/1000/2500M) USB: 1x USB 3.0 port Two buttons: power/reset and mode (BTN_0) LEDS: blue, red, blue+red=pink UART: 3.3V, TX, RX, GND / 115200 8N1 **Installation via U-Boot rescue** 1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1 2. Connect to the WAN port and hold the reset button while booting the device. 3. Wait for the LED to blink 5 times, and release the reset button. 4. Open U-boot web page on your browser at http://192.168.1.1 5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade. 6. Wait for the router to flash the new firmware. 7. Wait for the router to reboot itself. **Installation via sysupgrade** Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings. **Installation via SSH** Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command: ``` sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-emmc-squashfs-sysupgrade.bin ``` **Factory MAC** You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4` ``` dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C ``` **Enlarging a partition** Though device has 8GB eMMC, it uses only 2GB `/dev/mmcblck0p6` as `rootfs` for `/rom` and `/overlay` leaving `/dev/mmcblck0p7` as empty unused space. ``` sgdisk -p /dev/mmcblk0 ``` ``` Disk /dev/mmcblk0: 15269888 sectors, 7.3 GiB Sector size (logical/physical): 512/512 bytes Disk identifier (GUID): 2BD17853-102B-4500-AA1A-8A21D4D7984D Partition table holds up to 128 entries Main partition table begins at sector 2 and ends at sector 33 First usable sector is 34, last usable sector is 14942174 Partitions will be aligned on 1024-sector boundaries Total free space is 11197 sectors (5.5 MiB) Number Start (sector) End (sector) Size Code Name 1 8192 9215 512.0 KiB 8300 u-boot-env 2 9216 13311 2.0 MiB 8300 factory 3 13312 21503 4.0 MiB 8300 fip 4 21504 29695 4.0 MiB 8300 config 5 29696 62463 16.0 MiB 8300 kernel 6 62464 4256767 2.0 GiB 8300 rootfs 7 4257792 14940159 5.1 GiB 8300 ``` You can fix that by loading into `initramfs-kernel`, deleting empty `mmcblck0p7` partition and resizing `mmcblck0p6` ``` sysupgrade -F /tmp/openwrt-initramfs-kernel.bin ``` Install and run cfdisk ``` opkg update && opkg install cfdisk cfdisk /dev/mmcblck0 ``` - Select `mmcblck0p7` -> Delete - Select `mmcblck0p6` -> Resize -> Write -> yes -> Quit You will not see any difference in `cat /proc/partitions` after that but just flash a `sysupgrade` and you'll get the whole 7.3GB space for the `/overlay`. Co-developed-by: hecatae <horus.ra@gmail.com> Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com> Link: https://github.com/openwrt/openwrt/pull/18220 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> |
||
|
Erik Servili
|
a0c1c9df97 |
qualcommax: ipq60xx: add support for Netgear WAX610 and WAX610Y
Netgear WAX610 / WAX610Y is a 802.11ax AP claiming AX1800 support.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512MB
* Storage: Winbond W29N01HZBINF 128MB NAND
* Ethernet:
* 2.5GbE RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Power: Dual-color LED (Green / Orange), Single-color LED (Blue)
* Ethernet: Dual-color LED (Green / Orange)
* 2.4Ghz WiFi: 2x Single-color LED (Blue, Green)
* 5Ghz WiFi: 2x Single-color LED (Blue, Green)
* Buttons:
* 1x Reset
* UART: 4-pin populated header
* Pinout 1 - VCC, 2 - GND, 3 - TX, 4 - RX
Installation:
=============
Web UI method
-------------
Set up the device using the stock web UI in local management mode.
Download the ui-factory.tar image.
* Enter the Management tab
* Select Maintenance->Upgrade->Firmware Upgrade
* Ensure the "Upgrade Options" field has "Local" selected
* Click "Browse File" and select the image
* Click "Upgrade" (NOT "Upgrade Now") at the bottom of the page
The device will install the image but reboot back into the vendor
firmware. Return the to Firmware Upgrade page as above and select
"Boot up Backup Firmware". The device should reboot into OpenWRT.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot netgear_wax610-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the command line.
Signed-off-by: Erik Servili <serverror@serverror.com>
Link: https://github.com/openwrt/openwrt/pull/18377
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
||
|
Daniel Golle
|
52bea8702c |
uboot-envtools: add support for ASUS ZenWiFi BT8 (ubootmod)
We are using a replacement bootchain on that device, so add default UBI environment settings. Signed-off-by: Daniel Golle <daniel@makrotopia.org> |
||
|
Weikai Kong
|
a1bf306bb7 |
qualcommax: ipq60xx: add Linksys MR7500 support
Codename: Divo Hardware specification: ======== SoC: Qualcomm IPQ6018 RAM: 512MB (2x ESMT 256MB DDR3L M15T2G16128A–DEBG2R) NAND Flash: 512MB (Macronix MX30UF4G18AC or SK Hynix H27S4G8F2EDA-BC) Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C-B0) Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075) WiFi1: 6GHz ax 4x4@20/40/160 MHz (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229 WiFi2: 5GHz ax 2x2@20/40/80 MHz (Qualcomm QCN5052 + Skyworks SKY85755-11) - channels 36-177 WiFi3: 2.4GHz ax 2x2@20/40 MHz (Qualcomm QCN5022 + Skyworks SKY8340-11) IoT: Bluetooth 5 (CSR8811) - not implemented LED: 1x RGB status + USB Blue (PWM) USB: 1x USB 3.0 Button: WPS, Reset Flash instructions (Without Serial): ======== Open Linksys Web UI - http://192.168.1.1/ca or http://linksysxxxxx.lan/ca depending on your setup. xxxxx is the last 5 digits from the SN found on a sticker under the device. Click on the Linksys Logo to by-pass smart app registration. Login with your admin password. The default password can be found on the same sticker. To enter into the support mode, click on the “CA” link and the bottom of the page. Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button. Click start. Ignore all the prompts and warnings by click “yes” in all the popups. Flash instructions (With Serial): ======== 1. Installation using serial connection from OEM firmware (default login: root, password: admin): - fw_printenv -n boot_part In case of 2: - flash_erase /dev/mtd13 0 0 - nandwrite -p /dev/mtd13 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin or in case of 1: - flash_erase /dev/mtd15 0 0 - nandwrite -p /dev/mtd15 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin After first boot install firmware on second partition: - mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel or: - mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel 2. Installation from initramfs image using USB drive: Put the initramfs image on the USB drive: - dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda Stop u-boot and run: - usb start && usbboot $loadaddr 0 && bootm $loadaddr Write firmware to the flash from initramfs: - mtd -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel and: - mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel 3. Back to the OEM firmware: - mtd -e kernel -n write FW_MR7500_1.1.12.211919_prod.img kernel and: - mtd -r -e alt_kernel -n write FW_MR7500_1.1.12.211919_prod.img alt_kernel 4. USB recovery: Put the initramfs image on the USB: - dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda Set u-boot env: - fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr' - fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi' AQR firmware: ======== 0. Firmware extracting: To extract the firmware, use unblob (unblob.org) 1. Firmware loading: To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function. To do this, you need to modify u-boot env: With USB recovery: - fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi' and without: - fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi' 2. Firmware updating: Newer firmware (AQR114C.cld) is available in the latest OEM firmware (https://downloads.linksys.com/support/assets/firmware/FW_MR7500_1.1.12.211919_prod.img). Copy AQR114C.cld to /lib/firmware/marvell Link: openwrt#17428 Signed-off-by: Weikai Kong <priv@pppig236.com> Link: https://github.com/openwrt/openwrt/pull/18185 Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
|
Chukun Pan
|
c3f2bb7afc |
qualcommax: ipq60xx: add GL.iNet GL-AX1800/AXT1800 support
Specifications: SoC: Qualcomm IPQ6000 RAM: 512 MiB Flash: 128 MiB NAND ETH: Qualcomm QCA8075 WLAN1: 2.4GHz 802.11b/g/n/ax 2x2 WLAN2: 5GHz 802.11a/n/ac/ax 2x2 Button: Reset, Switch USB: 1x 3.0 SD slot: 1 in GL-AXT1800 Install via stock firmware: Upload factory.bin in stock firmware's upgrade page, do not preserve settings. Install via uboot web failsafe: Push the reset button for 5 seconds, then use broswer to access http://192.168.1.1, and upload factory.ubi. Afterwards upgrade can use sysupgrade image. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> Link: https://github.com/openwrt/openwrt/pull/14950 Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
|
Scott Mercer
|
46e376c935 |
uboot-tools: migrate uboot-envtools to uboot-tools
Generalize and merge uboot-envtools package into uboot-tools package. Remove existing uboot-envtools package. Signed-off-by: Scott Mercer <TheRootEd24@gmail.com> |