Mikrotik RouterBOARD 2011 series are AR9344-based wired routers, with
optional 2,4GHz 802.11n 2x2:2 Wi-Fi radio, with desktop or rack-mount
capability, featuring 5 gigabit Ethernet ports and 5 fast Ethernet
ports. Different variants of the board are supported using a single
image.
Bare-bones RouterBOARD 2011LS is supported using the same image.
Specification:
- Power: 10-28V input via 5,5/2,1 DC barrel jack, or terminal block on
some boards
- CPU: AR9344 at 600 to 750MHz (configurable)
- RAM: 128MB (64MB in early versions) DDR2
- Flash: 128MB (64MB in early versions) NAND flash
- Gigabit Ethernet: 5 ports via AR8327 switch (eth1 to eth5)
- Fast Ethernet: 5 ports via AR9344 built-in switch (eth6 to eth10)
- SFP: single port through AR8327 switch (SGMII at port 6)
- PoE in: passive input up to 28V at eth1
- PoE out: passive output up to 28V at eth10
- USB: optional micro-AB host port or type-A host port
- Console: optional Cisco-style RS232 console at the back of the device,
on budget devices available as 3.3V UART via testpoints
- LCD: 2" touchscreen-equipped LCD (unsupported)
Installation:
- perform TFTP boot of initramfs image as for netinstall procedure
typical for Mikrotik devices
- when initramfs image boots, use sysupgrade to perform final
installation.
If upgrading from ar71xx, clean installation should be performed, as the
devices now uses yafut to handle kernel image.
TODO:
- 64MB NAND variant using K9F1208U0C isn't yet supported, because it
needs disabling subpage write support for that chip. A proper solution
would be to fix that in kernel, but I don't have this variant to test
with currently.
- The same is true for GD9FU1G8F3A NAND, which isn't ONFI compliant and
needs definition in kernel for proper geometry.
- SFP port probes over I²C and gigabit link is possible, but currently
the drivers lack support of handling link status information to
userspace, including swconfig. Link will appear as always up.
Currently, link status logging can detect something, but status both
for ports 0 and 6 is logged simultaneously,
but "swconfig dev switch0 show" will always show link up on port 6.
- Not yet fully known connection to display and touch panel, but some
documentation is available (seemingly connected via SPI, according to
Mikrotik's open source code at [1])
[1] https://github.com/robimarko/routeros-GPL
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17617
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Passing QMP pipe clocks was upstreamed, but it requires conversion single
QMP node, so backport both of those instead of our downstream patch.
Signed-off-by: Robert Marko <robimarko@gmail.com>
In order to free up some more number space, simply renumber existing
upstreamed patches starting from 0 again.
Signed-off-by: Robert Marko <robimarko@gmail.com>
With the spi-qpic-snand driver now supporting reading ECC requirements
from the NAND chip itself, there's no need to set those in the DTS
anymore avoiding issues with devices of the same revision using
different NAND types with varying ECC requirements.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18723
Signed-off-by: Robert Marko <robimarko@gmail.com>
Updating the spi-qpic-snand driver with the latest patches sent
upstream and remove custom patches.
These patches add error handling fixes, use of right read location in
read ops, removal of unused variable, ability to read user config and
nand chip requirements, and support for 8bits ECC strength.
Tested on: Gl.iNet GL-B3000 & Linksys MR5500, MX2000, MX5500, SPNMX56
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18723
Signed-off-by: Robert Marko <robimarko@gmail.com>
Multiple conf support was upstreamed into kernel 6.10, so lets use the
upstreamed patches and mark them as so.
Signed-off-by: Robert Marko <robimarko@gmail.com>
MP5496 patches are not part of 6.15, but rather will be part of 6.16 as
they are no in 6.15 RC releases but they are in linux-next.
Signed-off-by: Robert Marko <robimarko@gmail.com>
When many multicast entries are installed broadcast flooding might
potentially stop working for several ports. This is because the layer
2 broadcast flood port mask index has the wrong offset. It should be
9 bits, matching the 2^9 = 512 indexes on rtl838x, not 12.
The wrong offset leads to L2_BC_FLD_PMSK being set to 504, not 511
((511 << 12) >> 9) & 511 = 504). So, as by default an unset PMSK
is set to all ports, the issue would only become noticeable once
many multicast entries are installed, causing the 504th entry to be set
to something other than all ports.
Fixing this by setting the offset to 9 bits, to correctly point to our
511th reserved entry for all ports.
Tested-on: ZyXEL GS1900-24HP v1
Fixes: 28e972b2ea ("realtek: Configure initial L2 learning setup")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Link: https://github.com/openwrt/openwrt/pull/18733
Signed-off-by: Robert Marko <robimarko@gmail.com>
This additional board.d script creates the "/tmp/sysinfo/oem_name" file
and populates it with the proper OEM "supported_devices" metadata entry
to be used by the new fwtool.sh oem detection feature.
(#18554): add oem image dectection to fwtool.sh
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18656
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update block NVMEM driver based on backported OF partition support.
Note the different MMC card DT binding compared to the previous
downstream solution: Instead of having a 'partitions' subnode inside
a 'block' node, the 'partitions' node now resides directly under the
node representing the card.
In order to make references to the 'boot0' or 'boot1' hw partitions
you will have to define 'partitions-boot0' or 'partitions-boot1', and
move the NVMEM layout into a partition (you may, of course, use
'fixed-partitions' for that, and cover the whole device, if needed).
See also https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/mmc/mmc-card.yaml?h=v6.13
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add network config for single-port Gateworks venice boards such that the
ethernet port is the WAN port instead of the default being a LAN port.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/18629
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some DTS files have a qsgmii link mode for the CPU port. This does
not harm but it is wrong. The CPU port of the realtek switch is always
directly connected to the switch by some unknown wiring and should
therefore be described as internal. Align the wrongly defined DTS
files to the standard.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18691
Signed-off-by: Robert Marko <robimarko@gmail.com>
- Fix order of patches (3d483a10327f was merged before 34d5a86ff7bb).
- Reorganize patch numbers now that < 6.12 patches are no longer needed.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This patch was added on linux v6.13 in order to avoid simple is_visible
functions on hwmon drivers.
See 79bc0af904
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Upstream e2015942e90a couldn't be backported to 6.6 because the following
symbols were missing:
- disable_work
- disable_work_sync
- enable_work
See e2015942e9
Upstream 34e5ededf4b8 couldn't be backported to 6.6 because the following
symbol was missing:
- pcim_iomap_region
See 34e5ededf4
Reorganize patch numbers now that < 6.12 patches are no longer needed.
The following patches still differ from upstream:
- e340bff27e63
phy_set_eee_broken symbol is missing in 6.12
https://github.com/torvalds/linux/commit/e340bff27e63
The following patches can't be backported to 6.12 due to missing symbols:
- 5e7a74b6a357
phy_disable_eee_mode symbol is missing in 6.12
https://github.com/torvalds/linux/commit/5e7a74b6a357
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Commit d7e82c78d7 added a generic kernel patch that exposes a new
symbol REALTEK_PHY_HWMON when REALTEK_PHY and HWMON are enabled. The new
symbol was added to kmod-phy-realtek, but the kmod is not used in the
realtek target.
Fixes: d7e82c78d7 ("generic: backport Realtek PHY patches from upstream")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Avoids some pointless boilerplate.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18675
Signed-off-by: Robert Marko <robimarko@gmail.com>
This seems to be some manual patch editing or rebasing bug.
Found with grep ' '.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18675
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit 1c993da8ff.
VSC kmod is broken and is causing all targets to fail compiling so revert.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Probing of the RTL8214FC on RTL839x is currently very strange.
- On RTL8393 nothing is detected and only generic PHY is reported
- On RTL8392 the port 1 is not detected while port 2-4 seem to work
Someone left a special RTL8393 detection rules that seems to indicate
that the we probe the internal SerDes instead. That is not true. Since
upgrade to kernel 6.6 the RTL8218/RTL8214FC detection is 100% accurate
and probing functions are only called when really needed.
Fix the issue by removing the condition. For now do PHY patching only
on the RTL838x where it already worked before.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18671
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Removes the need for a remove function in platform_device.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18660
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Easy way to add compatibility for kernel 6.12.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18660
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix DTB warning when compiling an image by adding the missing hash sign
of adress-cells in the usb_dwc node.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18672
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit fc3ff2af0c introduced reading
ECC strength from the device tree. Linksys MR5500 uses the mx-base dtsi
which was originally developed for Linksys MX2000 and MX5500 where the
ECC strength is set to 8. Correct this and set it to strength of 4 as
per the NAND specs for Gigadevice GD5F2GQ5REYIH.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18672
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit 34e5bc4af54d366147a83904c094d54fec7fb025.
While fixing support for 2.5Gbps mode on uniphy in phy to phy link
setups, it inadvertently broke fixed link scenario. So let's revert this
commit until there's a fix that doesn't impact fixed links.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18668
Signed-off-by: Robert Marko <robimarko@gmail.com>
fixes the following warning seen in bootlog
"Kernel image misaligned at boot, please fix your bootloader!"
Fixes: 3307fe8 ("qualcommax: ipq50xx: add support for GL.iNET GL-B3000")
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18658
Signed-off-by: Robert Marko <robimarko@gmail.com>
The factory image generation for the Genexis EX400 image currently fails
if CONFIG_TARGET_ROOTFS_INITRAMFS is disabled.
Create the factory image only if said config option is enabled to avoid
failing builds.
Signed-off-by: David Bauer <mail@david-bauer.net>
These symbols were found when adding 6.12 kernel support for the
ath79 target.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18653
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
These get dynamically set, not relevant for targets.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16547
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
