b14cf98 router: log “Sending a RA on lan” at LOG_DEBUG
c2810fe odhcpd: update cmake file
8c2c065 odhcpd: convert README to markdown
3b96480 odhcpd: allow the use of an alternative cfg file
7328bfe odhcpd: remove confusing #defines
cdb9e5b odhcpd: improve RFC9096 § 3.5 SLAAC compliance
RFC9096 § 3.5 SLAAC compliance introduces a new config option (odhcpd
piofolder), which may wear out the flash under certain conditions (for
example: ISPs with dynamic IPv6 prefixes which disconnect the clients
every X hours).
Therefore, setting "dhcp.odhcpd.piofolder" to persistent storage in the
router flash is not advisable and should be set to other kinds of
persistent storage such as USBs, SDs, NVMEs...
In order to prevent wearing out the router flash it's set to ephemeral
storage by default (tmp):
uci set dhcp.odhcpd.piofolder="/tmp/odhcpd-piofolder"
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Interface might be down or scanning. Better do a full restart in order to avoid
messing up the runtime state.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
after change include/package-pack.mk in 16416782f1, must use ALTERNATIVES to create soft link, otherwise the packing will be messed up.
Fixes: openwrt#20270
Fixes: openwrt#20291
Fixes: 16416782f1 (include: make APK packing mtime reproducible)
Signed-off-by: Andy Chiang <AndyChiang_git@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/20283
Signed-off-by: Robert Marko <robimarko@gmail.com>
When a phy appears after setup has already been attempted, tell netifd
to retry setup for all failed wireless devices.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This can be used by other services to trigger reconfiguration, or detect when
PHY renaming has been performed.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ensures that renaming is handled properly. For disabled radios, setup is
performed with an empty list of interfaces.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
c3bf8fd913a4 interface: fix reload for devices that point to vlan aliases
22216cac7c94 bridge: fix reload when ports refer to aliased vlans on another bridge
ecca21ca07dd system: add logging wrappers for basic system functions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not allow hostapd phy state update to bring up links as long between mld_set
and mld_start calls. Configuration on other PHYs could still be pending.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Bring up AP interfaces, even if no frequency update was provided.
Fixes bringup when a MLO STA on the same radios connects to fewer links
than available, or to a non-MLD AP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make the package empty if ucode wifi scripts are being used (since iwinfo is
provided by wifi-scripts in that case). This fixes packages that explicitly
select iwinfo
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There are no supported drivers where it even makes sense to disable WMM
anymore, since so much depends on it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The option is an array, and for each entry there should be one generated
line in hostapd.conf. Commas also need to be replaced with whitespace
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Removing the last remaining link from an MLD AP interface removes the
interface as well. Re-create the interface if necessary on config changes.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Can also be used for a client mode interface that is able to connect on
multiple bands individually, while handling hostapd state for the correct
band.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- fix the variable name in the configuration file
- provide a default scan list in case the user did not configure it (MLO preparation)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mlo specific hostapd ubus call from wireless handler to netifd core
ucode script. This avoids unnecessary queueing and the fake MLO wireless
device.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make sure that the package gets updated after the last fix.
Fixes: cd20ae44f2 ("uqmi: fix data-format parsing")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
wda-get-data-format now returns an object instead of a single string.
Account for this change when reading the packet data format.
Suggested-by: Sebastian Ertz (https://github.com/sebastianertz)
Signed-off-by: David Bauer <mail@david-bauer.net>
2859741d971e dhcpv4: store reqopts as uint8_t
6d342cc03bf7 odhcpd: add DNR (RFC 9463) support
c89b8b3f2ff3 odhcpd: make the IPv6 RA DNR lifetime configurable
066b3dc6ec1a netlink: fix a memory leak
171140e90b6a odhcpd: add a helper function for addr6/prefix parsing
5585b969c18f router: move pref64 calculations to the config stage
4308384748be dhcpv6: add ipv6 pxe support
6e1ad492cef5 router: replace ssize_t with size_t
Signed-off-by: David Härdeman <david@hardeman.nu>
Link: https://github.com/openwrt/openwrt/pull/20022
Signed-off-by: Robert Marko <robimarko@gmail.com>
Version 6.15 - 29-Aug-2025
* netlink: fix missing headers in text output
* netlink: fix print_string when the value is NULL
Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/20021
Signed-off-by: Nick Hainke <vincent@systemli.org>
