The DTC recommends using wifi@0,0 as the node name to match the reg
property structure. Fix warning:
../dts/qca9557_fortinet_fap-221-c.dts:208.13-213.4: Warning (pci_device_reg): /ahb/pcie@180c0000/wifi@0,0,0: PCI unit address format error, expected "0,0"
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18242
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that we have a board file, add calibration variant for TP-Link
Archer C59 v1 and add ipq-wifi package for it.
Tested-by: Mateusz Jończyk <matjon@users.noreply.github.com>
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20401
Signed-off-by: Robert Marko <robimarko@gmail.com>
The latter is more descriptive in terms of what's going on.
Mostly found with
git grep gpios\ | grep 0\>
git grep gpios\ | grep 1\>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20116
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Also handle 2.4ghz LED in ath9k instead of generic.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20269
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Deprecated. Replaced with nvmem.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20176
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20176
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20176
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20176
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Also convert custom LED to one handled by ath9k.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20112
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17344
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Move the mac address patch to 10_fix_wifi_mac.
This uses an AR9287, which uses a smaller size for its calibration.
The PCI ID is also wrong.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19864
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that we have a board file, add calibration variant for TP-Link
Archer C60 v1 and add ipq-wifi package for it.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19993
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of having two LED entries that supposedly control the same
thing, set the pin properly.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18905
Signed-off-by: Robert Marko <robimarko@gmail.com>
The driver makes its own ath9k LED which handles everything.
Simplifies DTS slightly.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20023
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling for this is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20023
Signed-off-by: Robert Marko <robimarko@gmail.com>
In first commit I successfully bring WAN port into ethernet switch,
without realizing that I was using custom bootloader. But if using
original bootloader it do not works. WAN port in original bootloader
is tied to using its own GMAC.
This fix is made so this firmware will be compatible with orignal
bootloader, so the user can directly flash from stock firmware without
changing anything.
Signed-off-by: Roy H <roy@altbytes.com>
Link: https://github.com/openwrt/openwrt/pull/20039
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Despite having the same tplink.dtsi file, there are differences in wifi
Move wifi nodes out of dtsi to make it clear what the chipset is and
what calibration size should be used.
While at it, change to use led-sources to simplify LED setup.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20024
Signed-off-by: Robert Marko <robimarko@gmail.com>
They have the same 0x200 calibration size.
Added various compatible lines in various places to make it clear what
device we're talking about.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19863
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These devices use AR9285, which uses 1f8 as the calibration size, not
440 like newer chips do. Actually the driver mandates a minimum of 200.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19863
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add calibration variant and ipq-wifi package for Xiaomi AIoT AC2350
Signed-off-by: Igor Dyatlov <dyatlov.igor@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19707
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
It's also a bit funny matching against phy0 and phy1 when both differ
between ath9k and ath10k.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19862
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18904
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k documentation says to use pci168c strings for the compatible
string, probably because the OWL loader uses it to overide bogus pci IDs
like abcd. This is not the case with ath10k and the documentation
explicitly states to use qcom,ath10k.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18920
Signed-off-by: Robert Marko <robimarko@gmail.com>
This device does not come with a pci card. It has a slot where one can
get supplied. What's more, nvmem or ieee80211 frequency limits are not
applied here. It can just get removed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18920
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18906
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18908
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
Set the pcie device to qcom,ath10k as the Documentation says, The pci
line implies it's ath9k when it's actually ath10k.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18873
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18873
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k driver creates an ath9k LED by default. Instead of having a
non functional LED, configure it properly and remove the extra as it's
not needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Zoltan HERPAI wigyori@uid0.hu
Link: https://github.com/openwrt/openwrt/pull/18907
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The vendor DTS defined incorrect GPIOs for the LEDs, which caused them
to not function properly. Initially, the WAN, WLAN LEDs appeared to
work, but further testing showed that they were non-functional.
This patch corrects the GPIO assignments in the DTS, restoring full LED
functionality including blinking, except the power LED which cannot be
software controlled.
Tested on a CF-EW71 v2 unit.
Fixes: ee3a6adc6c ("ath79: add support for Comfast CF-EW71 v2")
Signed-off-by: Felix Golatofski <git@xdfr.de>
Link: https://github.com/openwrt/openwrt/pull/19665
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Dell/SonicWall APL27-0B1 (marketed as SonicPoint ACi) is a dual band
wireless access point. Very similar to already supported APL26-0AE,
which all antennas are external, while this variant has internal
antennas. End of life as of 2022-07-31.
Specification
SoC: QualcommAtheros QCA9550
RAM: 256 MB DDR2
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9890 oversized Mini PCIe card
Ethernet: 2x 10/100/1000 Mbps QCA8334
port labeled lan1 is PoE capable (802.3at)
USB: 1x 2.0
LEDs: LEDs: 6x which 5 are GPIO controlled and two of them are dual color
Buttons: 1x GPIO controlled
Serial: RJ-45 port, SonicWall pinout
baud: 115200, parity: none, flow control: none
Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.
Installation
1. Prepare TFTP server with OpenWrt sysupgrade image and rename that
image to "ap135.bin".
2. Connect to one of LAN ports.
3. Connect to serial port.
4. Hold the reset button (small through hole on side of the unit),
power on the device and when prompted to stop autoboot, hit any key.
The held button can now be released.
5. Alter U-Boot environment with following commands:
setenv bootcmd bootm 0x9F110000
saveenv
6. Adjust "ipaddr" (access point, default is 192.168.1.1) and "serverip"
(TFTP server, default is 192.168.1.10) addresses in U-Boot
environment, then run following commands:
tftp 0x80060000 ap135.bin
erase 0x9F110000 +0x1EF0000
cp.b 0x80060000 0x9F110000 $filesize
7. After successful flashing, execute:
boot
8. The access point will boot to OpenWrt. Wait few minutes, until the
wrench LED will stop blinking, then it's ready for configuration.
Notes
By default no power is provided on USB port, so attached USB devices
won't enumerate. To change that enable regulator with:
echo "enabled" > /sys/devices/platform/output-usb-vbus/state
To disable power write "disabled" to the same file.
Ther regulator state will reset on reboot, consider running this command
on hotplug event or add it to /etc/rc.local. The hotplug event should
look like this:
if [ "${PRODUCT}" = "1d6b/2/606" ] && [ "${ACTION}" = "add" ]; then
echo "enabled" > /sys/devices/platform/output-usb-vbus/state
fi
Place it in /etc/hotplug.d/usb/10-usb-power.
Known issues
Initramfs image can't be bigger than specified kernel size, otherwise
bootloader will throw LZMA decompressing error. Switching to lzma-loader
should workaround that.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250529202033.28250-2-tmn505@terefe.re/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add/enable 2nd USB bus (integrated ath3k bluetooth) to dts. This already
exists in the qca956x dtsi, adding the pointer here to bring the bluetooth to life.
The 2nd bus hosts the integrated bluetooth at 0x1b400000.
See in the comments for more info:
c5b7ec8cee
Tested-by: Russ Innes <russ.innes@gmail.com> on Ubiquiti Amplifi HD .
Signed-off-by: Russ Innes <russ.innes@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19303
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Changing the node names arbitrarily broke existing configurations, which
rely on the device path in /etc/config/wireless.
Revert that part of the change without altering the compatible strings.
Fixes: 7e09959efd ("mac80211: fix wmac node names")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The upstream submission for this mandates the node to be named wifi
instead of wmac. Change all ath79 entries to match the new names and
remove the compatibility patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19328
Signed-off-by: Robert Marko <robimarko@gmail.com>
Due to a bug, USB is not powered on after boot on hAP ac.
This prevents extroot configurations from working as overlayfs is mounted
before USB device can be powered on. This commit fixes this by enabling USB
in devicetree.
Related discussion links:
- https://forum.openwrt.org/t/usb-power-is-off-on-boot/229007
---
Extroot configuration requires the USB to be powered on before
preinit_main/80_mount_root. Probably the simplest approach is to enable
it in the devicetree. Another approach would be to add a script into
/lib/preinit that will power on USB via /sys/class/gpio/usb-power/value
E.g.
cat /lib/preinit/79_power_on_usb
do_power_on_usb(){
echo '1' > /sys/class/gpio/usb-power/value
}
boot_hook_add preinit_main do_power_on_usb
Signed-off-by: Valeriy Manzhos <manzhos.va@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that we have a board file, add calibration variant for TP-Link
Archer C6 v2 and add ipq-wifi package for it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Upstream seems to be using led-sources instead of custom properties.
Code mostly taken from mt76.
Changed all(few) users of qca,led_pin to use the new format.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18805
Signed-off-by: Robert Marko <robimarko@gmail.com>
The "gpio-export" driver doesn't require a "reg" property in the
device tree, hence we don't need to use the "#size-cells" property
to describe the size of "reg".
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18290
Signed-off-by: Robert Marko <robimarko@gmail.com>
Mikrotik RouterBOARD 2011 series are AR9344-based wired routers, with
optional 2,4GHz 802.11n 2x2:2 Wi-Fi radio, with desktop or rack-mount
capability, featuring 5 gigabit Ethernet ports and 5 fast Ethernet
ports. Different variants of the board are supported using a single
image.
Bare-bones RouterBOARD 2011LS is supported using the same image.
Specification:
- Power: 10-28V input via 5,5/2,1 DC barrel jack, or terminal block on
some boards
- CPU: AR9344 at 600 to 750MHz (configurable)
- RAM: 128MB (64MB in early versions) DDR2
- Flash: 128MB (64MB in early versions) NAND flash
- Gigabit Ethernet: 5 ports via AR8327 switch (eth1 to eth5)
- Fast Ethernet: 5 ports via AR9344 built-in switch (eth6 to eth10)
- SFP: single port through AR8327 switch (SGMII at port 6)
- PoE in: passive input up to 28V at eth1
- PoE out: passive output up to 28V at eth10
- USB: optional micro-AB host port or type-A host port
- Console: optional Cisco-style RS232 console at the back of the device,
on budget devices available as 3.3V UART via testpoints
- LCD: 2" touchscreen-equipped LCD (unsupported)
Installation:
- perform TFTP boot of initramfs image as for netinstall procedure
typical for Mikrotik devices
- when initramfs image boots, use sysupgrade to perform final
installation.
If upgrading from ar71xx, clean installation should be performed, as the
devices now uses yafut to handle kernel image.
TODO:
- 64MB NAND variant using K9F1208U0C isn't yet supported, because it
needs disabling subpage write support for that chip. A proper solution
would be to fix that in kernel, but I don't have this variant to test
with currently.
- The same is true for GD9FU1G8F3A NAND, which isn't ONFI compliant and
needs definition in kernel for proper geometry.
- SFP port probes over I²C and gigabit link is possible, but currently
the drivers lack support of handling link status information to
userspace, including swconfig. Link will appear as always up.
Currently, link status logging can detect something, but status both
for ports 0 and 6 is logged simultaneously,
but "swconfig dev switch0 show" will always show link up on port 6.
- Not yet fully known connection to display and touch panel, but some
documentation is available (seemingly connected via SPI, according to
Mikrotik's open source code at [1])
[1] https://github.com/robimarko/routeros-GPL
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17617
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NEC Aterm WG2200HP is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
QCA9558.
Specification:
- SoC : Qualcomm Atheros QCA9558
- RAM : DDR2 128 MiB (2x ESMT M14D5121632A)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FM2I-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 3T3R (Qualcomm Atheros QCA9558 (SoC))
- 5 GHz : 4T4R (Qualcomm Atheros QCA9984)
- Ethernet : 5x 10/100/1000 Mbps
- switch : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO) : 12x/4x
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- Power : 12 VDC, 1.5 A (Max: 20 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image:
1. Connect and open serial console
2. Power on WG2200HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Rplace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the Diodes PI4IOE5V9539LE I2C Expander chip.
(compatible with NXP PCA9539)
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
- The data length of blocks in firmware image will be checked
(4M < threshold < 6M) on the stock WebUI of all versions, and
initramfs-factory.bin image of OpenWrt has the larger block data for
initramfs image. So that image cannot be applied to the stock WebUI
at all.
MAC addresses:
LAN : 98:F1:99:xx:xx:7C (config, 0x6 (hex))
WAN : 98:F1:99:xx:xx:7D (config, 0xc (hex))
2.4 GHz: 98:F1:99:xx:xx:7E (config, 0x0 (hex))
5 GHz : 98:F1:99:xx:xx:7F (config, 0x12 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17584
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add more DT labels and move a USB hub node to dts files of Aterm devices
as a preparation for adding support of Aterm WG2200HP.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17584
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The built-in watchdog is redundant when the device has an external
GPIO based hardware watchdog. And there is a conflict that both of
them will attempt to register the same device entry in sysfs. This
resulted in the built-in watchdog being unable to be activated.
This patch explicitly disables the built-in watchdog for devices
that use GPIO watchdog to fix the error:
[ 1.779206] ath79-wdt 18060008.wdt: unable to register misc device, err=-16
[ 1.786355] ath79-wdt: probe of 18060008.wdt failed with error -16
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18395
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add switch LED definitions for TP-Link TL-WR1043ND family, based on data
extracted from ar71xx board file. Update the LED labels to match current
pattern, i.e. drop the "tp-link:" prefix.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
