Hardware specifications:
- CPU: Freescale/NXP P2020, dual-core PowerPC @ 1 GHz
- RAM: 1 GB DDR3
- Flash: 2 MB NOR, 512 MB NAND
- Networking: 7x Gigabit Ethernet ports (via two Marvell 88E6171
switches, each attached to a different MAC)
- USB: 2x USB 2.0 ports (front panel)
- mini-PCIe slot
- RTC: Ricoh RS5C372A
- 4 buttons (via external MCU)
- 3 LEDs (via external MCU)
- LCD display (via external MCU)
Installation procedure:
1. Obtain the original MAC address table from the stock bootlog, for
example:
setting device eth0 to 00:90:7f:00:00:01
setting device eth1 to 00:90:7f:00:00:02
setting device eth2 to 00:90:7f:00:00:03
setting device eth3 to 00:90:7f:00:00:04
setting device eth4 to 00:90:7f:00:00:05
setting device eth5 to 00:90:7f:00:00:06
setting device eth6 to 00:90:7f:00:00:07
2. Open the case and move jumper JP1 from 2-3 to 1-2 to enter FAILSAFE
mode.
3. Power on the device and interrupt the boot process to access the U-Boot
shell.
4. Program the MAC base address into the EEPROM (text after '#' is a
comment):
mac ports 3
mac 2 00:90:7f:00:00:01 # first MAC address from bootlog
mac save
5. Reset the device and enter the U-Boot console again.
6. Connect a TFTP server to port 6 and boot the initramfs image:
setenv ipaddr 192.168.1.3
setenv serverip 192.168.1.2
setenv loadaddr 1000000
tftpboot $loadaddr openwrt-mpc85xx-p2020-watchguard_xtm330-initramfs-kernel.bin
bootm $loadaddr
7. (Optional) Backup all MTD partitions if you want the ability to restore
stock firmware.
8. Perform a normal sysupgrade from the initramfs environment.
9. Power off the device and move jumper JP1 back to 2-3.
10. The device will now boot OpenWrt.
Known issues:
- LCD, buttons and LEDs are controlled by an external MCU; the protocol is
currently unknown.
- The internal connection between the two Marvell switches is unused by
OpenWrt.
- The stock firmware uses an empty U-Boot environment; saving variables
modifies the environment and prevents a normal boot. FAILSAFE U-Boot
remains functional.
- WatchGuard configuration is encrypted; DSA MAC addresses are stored in
this configuration.
- Failsafe Ethernet works on port1.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21020
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>
It's shared by all targets. Unlike the other shared symbols, it's not
removed by kernel_oldconfig.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16756
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Enables use of NVMe storage devices with appropriate adapter in miniPCIe slots (including for boot)
in Turris 1.x routers and possibly NXP P2020RDB boards
(these are the only currently supported p2020 devices according to docs[^1]).
Proper detection, mountability and readability was proved to be working
on Turris 1.1, OpenWrt 21.02 with similar configuration.
Increases gzip compressed kernel size by approximately 37 KiB (from 3 703 KiB to 3 740 KiB).
Should boot from those devices be possible the driver needs to be built in.
Inclusion as a module would prevent this functionality.
CONFIG_BLK_DEV_NVME=y
Includes NVMe driver in the kernel.[^2]
CONFIG_NVME_CORE=y
Selected by CONFIG_BLK_DEV_NVME.[^3] Not necessarily needed to be enabled explicitly,
but included to match the form of similar functionality implementations
for mvebu, x86_64 and rockchip_armv8 targets.
CONFIG_NVME_MULTIPATH disabled explicitly to prevent using more space than necessary.
[^1]: https://openwrt.org/docs/techref/targets/mpc85xx
[^2]: https://cateee.net/lkddb/web-lkddb/BLK_DEV_NVME.html
[^3]: https://cateee.net/lkddb/web-lkddb/NVME_CORE.html
Signed-off-by: Šimon Bořek <simon.borek@nic.cz>
If the RTC module is compiled as a module, the hctosys fails to
initialize because ds1307 is loaded later.
Fixes:
[ 2.004145] hctosys: unable to open rtc device (rtc0)
[ 11.957997] rtc-ds1307 0-006f: registered as rtc0
This is similar to commit 5481ce9a11,
which was done for imx6 target.
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them
to the generic kconfigs. And resort the generic kconfigs while at it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
At this moment p2020rdb has broken images, because NOR memory connected
to eLBC bus isn't detected.
In 642b1e8dbed7 linux tree commit, config dependencies of MTD_PHYSMAP_OF
was changed and now MTD_PHYSMAP is required.
This patch adds MTD_PHYSMAP option to kernel config in p2020 subtarget
and fix booting of p2020rdb.
Fixes: 13b1db795f ("mpc85xx: add support for kernel 5.4")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This fixes some outstanding issues with the Kernel 5.4 build:
* Adds missing support patch for the Enterasys WS-AP3710i
* Fixes incorrect NAND symbols
* Adds patch for broken image wrapping
Signed-off-by: David Bauer <mail@david-bauer.net>
