The u-boot of cmcc_rax3000m_*-ddr3 declares a dependency on
trusted-firmware-a-mt7981-*-ddr3-1866mhz, while actually packages
the normal BL2. This causes build failure if the the non-1866m
variant isn't built.
According to the previous commit, it's intended to use the lower
frequency variant to fix device stability issues. Correct
BL2_DDRTYPE as intended.
Fixes: 028050da69 ("mediatek: CMCC RAX3000Me: fix stability issues")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Fix a typo on defining the PHY package kmod description that reference
phy-aeonsemi-as21x1x package instead of phy-aeonsemi-as21xxx.
Fixes: 08a616b216 ("generic: backport support for Aeonsemi AS21xxx PHY")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Do not allow hostapd phy state update to bring up links as long between mld_set
and mld_start calls. Configuration on other PHYs could still be pending.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Bring up AP interfaces, even if no frequency update was provided.
Fixes bringup when a MLO STA on the same radios connects to fewer links
than available, or to a non-MLD AP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Make the package empty if ucode wifi scripts are being used (since iwinfo is
provided by wifi-scripts in that case). This fixes packages that explicitly
select iwinfo
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There are no supported drivers where it even makes sense to disable WMM
anymore, since so much depends on it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
gpio pwm driver is only available on kernel 6.11+.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20187
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix typo in patch file suffix.
Signed-off-by: Wei-Ting Yang <williamatcg@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20178
Signed-off-by: Robert Marko <robimarko@gmail.com>
Introduce support for U-Boot for Airoha EN7581/AN7583. For EN7581
initial patch are already in U-Boot mainline and doesn't require
backport, for AN7583 some patch are still pending but already posted
upstream.
Also add for now, precompiled binary for ATF BL2 and BL31. Support for
ATF is planned and will come later.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Removed upstreamed patch: 0001-Don-t-keep-the-store-open-in-by_store_ctrl_ex.patch
Release notes:
This is a bug fix release.
This release incorporates the following bug fixes and mitigations:
Added FIPS 140-3 PCT on DH key generation.
Fixed the synthesised OPENSSL_VERSION_NUMBER.
Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/20133
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Package the generic kernel PWM GPIO driver as module to avoid the need
to build it into the kernel.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://github.com/openwrt/openwrt/pull/20160
Signed-off-by: Robert Marko <robimarko@gmail.com>
The option is an array, and for each entry there should be one generated
line in hostapd.conf. Commas also need to be replaced with whitespace
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Removing the last remaining link from an MLD AP interface removes the
interface as well. Re-create the interface if necessary on config changes.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Can also be used for a client mode interface that is able to connect on
multiple bands individually, while handling hostapd state for the correct
band.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- fix the variable name in the configuration file
- provide a default scan list in case the user did not configure it (MLO preparation)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mlo specific hostapd ubus call from wireless handler to netifd core
ucode script. This avoids unnecessary queueing and the fake MLO wireless
device.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This commit fixes stability issues on certain RAX3000Me devices. Some
devices has DDR3 RAM which don't able to work reliably at 2133 MHz
and require special BL2 (1866 MHz RAM freq).
Fixes: https://github.com/openwrt/openwrt/issues/20046
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20059
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The new profiles are intended for devices with DDR3 RAM which
don't able to work reliably at 2133 MHz.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20059
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Buffalo WSR-6000AX8 and AX8P models.
Hardware
--------
SOC: MediaTek MT7986B
RAM: 512MB
FLASH: 128MB SPI-NAND (Winbond)
WIFI 2.4G: (Embedded in SOC) b/g/n/ax, MIMO 4x4
WIFI 5G: (Embedded in SOC) a/n/ac/ax, MIMO 4x4
ETHERNET: 2.5GbE MaxLinear GPY211C (eth1: WAN)
ETHERNET: MediaTek MT7531AE 3xGbE (eth0: LAN1, LAN2, LAN3)
UART: 3.3V 115200 8N1
Serial(UART) Pin Layout
-----------------------
+-------+-------+-------+-------+
J4 | RX | TX | GND |(3.3V) |
+-------+-------+-------+-------+
(Bottom Side)
MAC Address Table
-----------------
lan1-3: board_data 0x4(text)
eth1/WAN: board_data 0x4(text)
WIFI 2.4G: lan1 + 2
WIFI 5G: lan1 + 9
Installation
------------
1. Set up a TFTP server with the IP address "192.168.11.2".
2. Rename the OpenWrt initramfs image to "linux.ubi-recovery" and place it
in the TFTP server's root directory.
3. While holding down the AOSS button, power on the WSR-6000AX8 (or AX8P).
4. The device will automatically download the initramfs image
from the TFTP server and boot into it.
5. Once booted, run "sysupgrade -n" using the OpenWrt sysupgrade image
to complete the installation.
Recovery
--------
1. Decrypt the official firmware image using "buffalo-enc".
example:
$ buffalo-enc -d -i wsr_6000ax8_jp_100 -o wsr_6000ax8_jp_100.dec \
-l -O 0xc8
2. Run "sysupgrade -F -n" with the decrypted image.
Signed-off-by: Shin Sato <shin.sugar.ssyysy2021@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/13107
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit add kernel module support for Infineon DPS310/DPS368/DPS422
digital barometric air pressure and temperature sensor.
Test on custom board based on Mediatek MT7988a.
Signed-off-by: Elwin Huang <s09289728096@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20101
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
of_gpio.h is deprecated in upstream Linux and may be removed soon. Get
ahead of things and remove it. Most of these drivers already use the
gpiod API.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20076
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is a smart door lock device equipped with OpenWrt 14.07 OEM
modified version Qdwrt
The OEM has closed down, This commit is intended to maximize the
remaining value of these devices. It can flash OpenWrt to become
an AP
Specification:
- SoC: MediaTek MT7628NN
- Flash: 8 MB
- RAM: 64 MB
- Power: DC 5V - 25V
- Ethernet: 1 x RJ45 (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only
- On-Board LED:
Status 1: GPIO/43 active-low
Status 2: GPIO/44 active-low
Power: AlwaysOn
- Button:
WPS / RESET: GPIO/14 active-low
- Bluetooth: CC2541 via UART1 (ttyS1) and GPIO/26-29
- RFID: MF RC522 on I2C@28
- RTC: DS1339 on I2C@68
- Shell (via CON1 cable)
- LED (Swipe card area):
- Green GPIO/3 active-high
- Red GPIO/11 active-high
- Matrix keypad: (active-low)
GPIO/20 GPIO/21 GPIO/19 (Rows)
GPIO/24 1 2 3
GPIO/25 4 5 6
GPIO/22 7 8 9
GPIO/23 BACK 0 ENTER
(Cols)
- UART: 1 x UART on PCB - 57600 8N1
- GPIO Relay: GPIO/42 active-high
- GPIO Buzzer: GPIO/15 active-high
Warning:
The original firmware does not use the device tree.
This device tree is written based on the content of /sys/devices/platform
and has been tested
Note:
- On the device, matrix keypad rows actually are columns, and the columns actually are rows
- The key code of the CLEAR key of the matrix keypad is BACK in the original firmware.
Issue:
- No drivers in mainline kernel for RFID and Bluetooth.
Flash Instruction:
Using SSH/Telnet:
1. Connect the board to the computer via RJ45 Ethernet
2. Login 10.10.10.1 with root password "szqdingnet123" (SSH Port 22, Telnet Port 9900)
3. Download openwrt firmware on the computer.
4. Setup a http server on computer. And use wget download openwrt firmware from computer
5. Use command "mtd -r write openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin firmware"
to flash
Using U-Boot WebUI:
1. Configure PC with a static IP address 10.10.10.2/24.
2. Open http://10.10.10.1
3. Use "mkqdimg -B qc202 -f openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin" to
make image.
4. Upload factory.bin via U-Boot WebUI.
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-qianding-smart-locker-and-flash.html
Original U-Boot firmware image tools:
https://gitlab.com/CoiaPrant/mkqdimg
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17471
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Make sure that the package gets updated after the last fix.
Fixes: cd20ae44f2 ("uqmi: fix data-format parsing")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
wda-get-data-format now returns an object instead of a single string.
Account for this change when reading the packet data format.
Suggested-by: Sebastian Ertz (https://github.com/sebastianertz)
Signed-off-by: David Bauer <mail@david-bauer.net>
The EN751221 has an XHCI that is compatible with MT7621.
While there is setup logic in the vendor code for both
EN751221 and MT7621, but MT7621 does not use it in mainline
or OpenWRT, and it appears to work correctly with EN751221.
Include SCSI / Mass Storage because many EcoNet devices
contain a builtin USB SD-Card reader.
Signed-off-by: Caleb James DeLisle <cjd@cjdns.fr>
Link: https://github.com/openwrt/openwrt/pull/20050
[Remove usb storage kmod from smartfiber_xp8421-b]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
