Do not verify the format of TLV. Leave that to lldpd.
These lldpd config entries:
config custom-tlv
list ports 'eth0'
option tlv 'replace oui 33,44,55 subtype 254 oui-info 55,55,55,55,55'
config custom-tlv
option tlv 'oui 33,44,44 subtype 232'
list ports 'br-lan'
list ports 'eth0'
config custom-tlv # oui-info truncated
option tlv 'add oui 33,44,33 subtype 66 oui-info 5555555555'
config custom-tlv
option tlv 'add oui 33,44,31 subtype 44'
config custom-tlv # invalid oui
option tlv 'add oui 3322 subtype 79'
config custom-tlv # invalid oui
option tlv 'oui 3312 subtype 74'
Produce the following lldpd.conf content:
configure ports eth0 lldp custom-tlv replace oui 33,44,55 subtype 254 oui-info 55,55,55,55,55
configure ports br-lan,eth0 lldp custom-tlv oui 33,44,44 subtype 232
configure lldp custom-tlv add oui 33,44,33 subtype 66 oui-info 5555555555
configure lldp custom-tlv add oui 33,44,31 subtype 44
configure lldp custom-tlv add oui 3322 subtype 79
configure lldp custom-tlv oui 3312 subtype 74
And lldpd (v1.0.13 on v22) logs the following:
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op replace oui 33:44:55 subtype fe
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:44 subtype e8
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:33 subtype 42
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:33 subtype 42
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:31 subtype 2c
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:31 subtype 2c
Sat Mar 16 19:11:39 2024 daemon.warn lldpcli[10915]: invalid OUI value '3322'
Sat Mar 16 19:11:39 2024 daemon.info lldpcli[10915]: an error occurred while executing last command
Sat Mar 16 19:11:39 2024 daemon.warn lldpcli[10915]: invalid OUI value '3312'
Sat Mar 16 19:11:39 2024 daemon.info lldpcli[10915]: an error occurred while executing last command
Sat Mar 16 19:11:39 2024 daemon.info lldpcli[10915]: lldpd should resume operations
( The last two TLV are invalid: their oui must be three hex bytes, comma
separated. Only the first hex byte of oui-info 5555555555 is used )
Depends on #14867 and its release version bump
Tested on: 22.03.6
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14872
(cherry picked from commit 8d1fe32c2c)
Link: https://github.com/openwrt/openwrt/pull/18343
Signed-off-by: Robert Marko <robimarko@gmail.com>
where csv = comma separated value(s)
Make the function more generic. Can use it for not only 'config'.
Now it can be used to parse interfaces for additional lldpd settings,
e.g. custom-tlv.
Tested on: 22.03.6
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14872
(cherry picked from commit a015f59880)
Link: https://github.com/openwrt/openwrt/pull/18343
Signed-off-by: Robert Marko <robimarko@gmail.com>
The lldp_class and lldp_location config option are only valid when
compiled with LLDP-MED support. If not they will cause lldpd not to
start.
Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
Link: https://github.com/openwrt/openwrt/pull/17571
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 2c22d7c3a4)
lldpd was updated, so reset PKG_RELEASE after the PKG_VERSION update.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit abbec429b4)
Changes (breaking):
- Remove support for building 802.3bt TLVs (broken).
Fix:
- Fix memory leaks in EDP/FDP decoding when receiving some TLVs twice.
- Do not set interface description continuously.
- Use a different Netlink socket for changes and queries.
Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
Link: https://github.com/openwrt/openwrt/pull/17570
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a18385041e)
Because these capability advertisements default to on in lldpd, they
became absent at reload, and not restart, due to how the reload logic
works ( keep daemon running, send unconfigured and then the new config
via socket ), and it was not evident unless you happened to be looking
for it (e.g. via pcap or tcpdump). It was also not evident from the
manpage ( have now sent patches upstream ).
At reload time, the unconfigure logic disabled them unless they were
explicitly enabled (compare with other settings where 'unconfigure' just
resets them). Now they default to on/enabled at init time, and are
explicitly 'unconfigure'd at startup if the user disables them via:
lldp_mgmt_addr_advertisements=0
lldp_capability_advertisements=0
In other words: explicit is necessary to disable the advertisements.
The same applies to 'configure system capabilities enabled'. Technically
'unconfigure'd is the default but now it is explicit at reload.
Tested on: 23.05.3
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
For interface type parameters, the man page documents patterns:
```
*,!eth*,!!eth1
uses all interfaces, except interfaces starting with "eth",
but including "eth1".
```
* Renamed `_ifname` to `_l2dev`.
* get the l2dev via network_get_physdev (and not l3dev)
* Glob pattern `*` is also valid - use noglob for this
The net result is that now interface 'names' including globs '*' and '!'
inversions are included in the generated lldpd configs.
Temporarily `set -o noglob` and then `set +o noglob` to disable & enable
globbing respectively, because when we pass `*` as an interface choice,
other file and pathnames get sucked in from where the init script runs,
and the `*` never makes it to lldpd.
Tested extensively on: 22.03.6, 23.05.3
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
[ squash with commit bumping release version ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
only available from >= 1.0.15
Comments are useful. Apparently this config parameter was committed when
openwrt used an older version of lldpd which did not yet support it.
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
For certain lldp_class scenarios (2 & 3) a policy must be set also.
Class 4 is default, although it's good to handle the policy eventuality.
Here, set a default lldp_policy for all lldp_class scenarios. Any
lldp_policy can now be set.
Depends on PR #14584 (which introduced an `if` block)
Tested on 22.03.5, 22.03.6
Signed-off-by: Paul Donald <newtwen@gmail.com>
Previously only partially implemented. After commit
5007f488bb lldp_location was never removed
Now, add the value of lldp_location to the generated config.
The location param has a few syntaxes, so the config acquires the first
usage from the man page: 'address country EU'
Supplementary fix for PR #14193 (this param was included in the original
PR #13018 but the lldp_location fixes were absent from PR #14193).
Tested on 22.03.5, 22.03.6
Signed-off-by: Paul Donald <newtwen@gmail.com>
from commit 3ce909914a
The lldpd man page says that "configure lldp tx-interval" can
specify an interval value in milliseconds by appending a "ms" suffix to
the figure. Thus mandating string handling, and not integer comparison.
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
from commit 909f063066
Now pass two params to get_config_cid_ifaces() for:
cid_interface
interface
Each of which is a CSV of interfaces.
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
from commit ac771313eb
portidsubtype takes 1 of 2 possible keywords which do not need quoting:
configure lldp portidsubtype ifname | macaddress
The third keyword 'local' is used in the syntax when individual ports
are being defined:
configure [ports ethX [,…]] lldp portidsubtype local value
When this syntax is used, quoting is useful (see test cases for lldpd).
In the init file, the 'local' syntax is unused.
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
from commit c98ee4dbb3
agent-type takes 1 of 3 possible keywords which do not require quoting:
configure lldp agent-type nearest-bridge | nearest-non-tpmr-bridge
| nearest-customer-bridge
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
Bind to the configured system interfaces only. Switchport interfaces
are no longer ignored and uci interface values for LLDPD are honored.
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
Init script reload with trigger to detect config file update.
Reload command added to attempt non-impactful lldpd reload where
lldpcli can be used to update config without process restart.
Config hash function used to track whether process restart is needed.
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
allow to overwrite the detected system capabilities e.g. if devices
does not operate as bridge.
Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
This reduces open coding and allows to easily add a knob to enable
it treewide, where chosen packages can still opt-out via "no-lto".
Some packages used LTO, but not the linker plugin. This unifies 'em
all to attempt to produce better code.
Quoting man gcc(1):
"This improves the quality of optimization by exposing more code to the
link-time optimizer."
Also use -flto=auto instead of -flto=jobserver, as it's not guaranteed
that every buildsystem uses +$(MAKE) correctly.
Signed-off-by: Andre Heider <a.heider@gmail.com>
There is currently a problem with making reproducible version of lldpd.
The tool version is generated based on 3 source:
1. .dist-version file in release tar
2. git hash with presence of .git directory
3. current date
Using the codeload tar from github results in getting the repo without
the .git directory and since they are not release tar, we don't have
.dist-version. This results in having lldpd bin with a version set to
the current build time.
Switch to release tar so that we correctly have a .dist-version file and
the version is not based on the build time.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
