Move "# CONFIG_NVMEM_LAYOUT_ASCII_ENV is not set" to the correct location.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18335
Signed-off-by: Nick Hainke <vincent@systemli.org>
All devices have already been migrated to the upstream PHY LED
API. This prevents users from adding new devices using this hack.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
The ar8216 switch driver supports exposing configuration of AR8327 and
AR8337 switch LEDs to the userspace, however it is only configurable
through platform data, causing the devices ported from ar71xx target to
lack the support.
Since there is still a long way to go until we can migrate the target to
qca8k, an interim solution is needed.
Extend ar8327_hw_config_of function to parse a "leds"
subnode, which will populate the missing platform data based on device
tree contents, and restore the existing support for the LEDs.
Standard bindings apply, mapping "reg" property to LED index, with
addition of "qca,led-mode" property, which selects HW (0) or SW (1)
mode, defaulting to HW mode.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Switch LEDs configured as active-low remain low instead of high upon
initialization, because in ar8327_leds_init, no distinction is made with
regards to LED pattern based on active_low property - only whether HW
mode is active. Select the proper initial pattern based also on
active_low to fix that.
While at that, simplify the equation ruling pattern selection for
setting brightness, avoiding unnecessary binary XOR operation, not
really valid for 'bool' type.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, if the phy driver does not implement the led_brightness_set
function, setting the LED will result in the following error message:
leds mdio-bus:*:green:lan: Setting an LED's brightness failed (-524)
Backport a patch to silence this error message.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/18080
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
RTL8261N is used on some Airoha and Realtek devices. Move the driver
from Mediatek to generic so it can be used everywhere.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18163
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_NET_SWITCHDEV option is needed by CONFIG_DSA and some other
options. It is boolean, we have to compile it into the kernel it self.
Activate it for all targets in the generic configuration, it is already
activated for most of them. This allows to install DSA drivers as a
module.
On the ramips/mt7620 target the kernel would grown by 4.5kB.
For some small targets which do not support a DSA switch by default the
option is deactivated.
Link: https://github.com/openwrt/openwrt/pull/17668
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes the handling of some FS copper SFP modules using the RollBall
protocol and needing some extra treatment.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This is only relevant for devices with USB support, and in itself changes
nothing in the kernel build. However, it is useful to further simplify the
dependencies of some USB network devices.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
The kmod-mlxsw-spectrum driver activated CONFIG_DCB indirectly already
on all targets which are building this driver. All other DCB capable
driver did not activate their DCB support.
CONFIG_DCB increases the uncompressed kernel size by about 7.8KB.
CONFIG_DCB is only needed some data center Ethernet cards and not used
on normal routers. Activate it only on the x86_64 and the armsr_arm64
target which are used on normal servers or in VMs.
Link: https://github.com/openwrt/openwrt/pull/17672
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Quoting the kconfig description for CONFIG_PCPU_DEV_REFCNT:
network device refcount are using per cpu variables if this option is
set. This can be forced to N to detect underflows (with a performance
drop).
This was introduced from kernel 5.13 and was wrongly set as disabled.
Some target actually enables it but this should be always enabled unless
refcount needs to be debugged (unlikely for production images)
Enable in generic and drop the entry in every other target.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18174
Signed-off-by: Robert Marko <robimarko@gmail.com>
Due to API changes during the backport, the default value of Tx LPI
timer is accidentally left unset, breaking the network if EEE is on.
Set the default timer to 1ms on init, and fix an incorrect condition.
Fixes: d8315d5358 ("kernel: backport Mediatek SoC EEE support")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Prior to commit 8a7d12d674,
cdc-ethernet USB LTE modems (e.g. Quectel EC200A) were consistently named
usb0. After 8a7d12d67, devices began renaming to eth1 due to an assumption
that local MAC addresses originate exclusively from the kernel. Some
devices provide driver-assigned local MACs, causing point-to-point
interfaces with driver-set MACs to adopt eth%d names instead of usb%d.
Restore the naming exception for point-to-point devices: interfaces
without driver MACs or with driver-provided local MACs will retain the
usb%d convention. This addresses issues reported in [1] and fixed in [2].
[1] https://lore.kernel.org/all/Z00udyMgW6XnAw6h@atmark-techno.com/
[2] https://lore.kernel.org/all/20241203130457.904325-1-asmadeus@codewreck.org/
Tested-by: Ahmed Naseef <naseefkm@gmail.com>
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17757
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport Mediatek SoC EEE support from net-next upstream.
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[refreshed patches]
Add validation and support for parsing of name/value pairs with CRLF line
endings.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17935
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add missing patch description, so all generic patches can be applied
to a kernel tree using 'git am'.
Fixes: d23e0a0086 ("kernel: backport MHI patch required by an upcoming mac80211 update")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import patch from MediaTek's SDK to hack-6.6 which dumps all relevant
registers of the Ethernet controller in case of a forced reset.
This can help to debug and find the cause for sporadic resets seen on
Filogic SoCs when used with OpenWrt's Linux 6.6.
Link: 73d44392b8
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add patch to fix Qcom SNAND driver and move the SNAND patches to
backports directory as they are shared between qualcommax and qualcommbe
target.
Fixes: #17897
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17900
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds new "mediatek,bmt-mtd-overridden-oobsize" property. The
property helps avoid "NMBM configuration mismatch" error if mtd "OOB size"
is not equal to the "spare size" which is stored in the nmbm signature.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17549
Signed-off-by: Robert Marko <robimarko@gmail.com>
Uses upstream DSA switch modules (rtl8365mb, rtl8366), similar to
RTL8367C and rtl8366rb swconfig drivers.
The package dependencies exclude targets built without kernel CONFIG_OF.
It also fixes the rtl8366rb LED support.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix broken NVMEM ASCII patch for x86 target as it does currently fail
compilation when OF is not compiled.
Also mute a warning for integer from pointer without a cast.
Fixes: 73a6cb983c ("generic: add pending support for NVMEM ASCII ENV layout driver")
Link: https://github.com/openwrt/openwrt/pull/17845
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add pending patch to support NVMEM ASCII ENV layout driver. This is a
generic driver to handle simple NVMEM partition that store environment
in a simple text format. This is the case for Linksys devinfo partition
that are litterally txt file with format "name=value\n"
Such driver works similar to u-boot,env with a similar format. While at
it also introduce a patch to generalize mac-base handling for also other
layout driver.
Link: https://github.com/openwrt/openwrt/pull/17839
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
b11bff90f2ad r8169: add support for RTL8125BP rev.b
b3593df26ab1 r8169: add support for RTL8125D rev.b
b299ea006928 r8169: adjust version numbering for RTL8126
bb18265c3aba r8169: remove support for chip version 11
2e20bf8cc057 r8169: remove unused flag RTL_FLAG_TASK_RESET_NO_QUEUE_WAKE
e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints
The EEE advertisement patch has been reworked for linux v6.6 because
phy_set_eee_broken() is only present on linux >= v6.13 and eee_broken_modes
declaration has been converted to a bitmap, so linkmode_set_bit() can't be
used either.
e340bff27eed623fb8e3721aa69e70
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
On some but not all devices using the RTL8221B 2.5GBit/s PHY the SerDes
setup sequence may hang under some circumstances (eg. <2500M link
partner present during boot).
RTL8221B-VB-CG 2.5Gbps PHY (C45) mdio-bus:01: rtl822xb_config_init failed: -110
Work-around the issue by performing a hardware reset and subsequent
retry of the SerDes setup, which seems to always succeed.
Doing this requires moving ALDPS setup to config_init (which is anyway
the better place for that) as it otherwise doesn't survive the reset.
Also disable listening on MDIO address 0 which may be used by other PHYs
despite being spec'ed as "broadcast address", as bus activity on address
0 may otherwise confuse the RealTek PHY for good reasons.
Tested-by: Luis Mita <luis@luismita.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ST1202 controller was added recently, but it was not disabled in the
generic config, so lets avoid individual target configs disabling it
and just disable it in generic config.
Link: https://github.com/openwrt/openwrt/pull/17746
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a backport of a btsdio patch for the cyw437 bluetooth controller.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/17717
Signed-off-by: Robert Marko <robimarko@gmail.com>
Import patch "net: phy: realtek: mark existing MMDs as present"
When using Clause-45 mode to access RealTek RTL8221B 2.5G PHYs some
versions of the PHY fail to report the MMDs present on the PHY.
Mark MMDs PMAPMD, PCS and AN which are always existing according to
the datasheet as present to fix that.
Fixes: #16823, #17183, #17232
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Tested-by: Juan Pedro Paredes Caballero <juanpedro.paredes@gmail.com>
Expose the temperature sensor built-into RTL822x 2.5G and 5G PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Refresh hack patches with make target/linux/refresh.
Fixes: 9508ca44eb ("kernel: backport improvement to page pool fragment handling from 6.7")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
1. Import pending patch to fix ramips/mt7621 64MB targets.
2. Do not enable CONFIG_PAGE_POOL_STATS by default.
Signed-off-by: Danila Romanov <pervokur@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As per @KanjiMonster comment: st1202_dt_init() calls devm_led_classdev_register_ext() before the internal data structures are properly setup, so the leds become visible to user space while being partially initialized, leading to a window where trying to access them causes a NULL pointer access.
Move devm_led_classdev_register_ext() to the last thing to happen during initialization.
Signed-off-by: Manuel Fombuena <fombuena@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17543
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some VRX518 modems fail to initialize properly with the error message
"dc_ep_clk_on failed". As a result, the DSL data path doesn't work.
This hack, which is based on code from the FRITZ!Box 7530 GPL archive,
fixes the issue. It changes the PCIe vendor/device ID to values matching
a Lantiq SoC. It also appears to emulate a Lantiq CPU ID register for
connected PCIe devices, by remapping the matching address area to a
specially crafted buffer using the address translation unit.
A dedicated compatible is created to activate this in
the device tree, so this shouldn't affect any devices other than
FRITZ!Box 7530/7520.
Original investigation was done in 59f5212517 which used the "avm,host_magic" property to enabled the patch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17622
Signed-off-by: Robert Marko <robimarko@gmail.com>
