This board is also as known as LC-HX3001
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: Foresee F35SQA001G 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain SSH access:
Method 1:
1. Connect UART Adapter to the router
2. UART pins are enabled, set the root password with passwd command
start the dropbear instance on port 22
Method 2:
1. Login into web interface, and restore the router with SSH enabled configuration.
2. After reboot Default Web interface password will be 12345678
SSH password is empty
Flash instructions:
1. Connect to HX21, backup everything, especially 'Factory' part.
3. Write new FIP:
mtd write openwrt-mediatek-filogic-hx_21-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
8. To write new BL2
Install mtd-rw
opkg update && opkg install kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd write openwrt-mediatek-filogic-imou_hx21-preloader.bin bl2
Signed-off-by: Jahidul Islam <hello@jahid.io>
Link: https://github.com/openwrt/openwrt/pull/20753
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The BPi R4 Lite can boot from microSD, SPI-NAND, SPI-NOR and eMMC.
Build menu-driven U-Boot for each storage option.
Provide options for installation from microSD to SPI-NAND and SPI-NOR,
and from SPI-NAND to eMMC (similar to BPi-R3).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Build the (upstream) configuration for the MT7987 reference board, and
enable support for DT-overlay application which will be necessary to
use the image for the MT7987 RFB generated in OpenWrt.
Adapt our downstream patches (generic reset button, rootdisk selection)
for MT7987 to prepare for real-world boards.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This board is also as known as E-Life ETR631-T/ETR635-U.
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Uncompress the configuration:
* Enter fakeroot if you are not login as root.
tar -zxf <filename>.tar.gz
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; telnetd; ) &
5. Repack the configuration:
tar -zcf backup.tar.gz etc/
6. Upload new configuration via web interface, now you can connect to
KOMI A31 via telnet.
Flash instructions:
1. Connect to KOMI A31, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-konka_komi-a31-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-konka_komi-a31-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20357
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The most relevant change is the removal of the empty board_init()
functions by u-boot/u-boot@70a4d1fa1d, which makes many patches not
apply anymore and also requires most board defconfigs to be updated
by adding "# CONFIG_BOARD_INIT is not set" to them.
Also some config symbols have been renamed and downstream boards
had to be adapted accordingly:
u-boot/u-boot@0fd9a3480a ("env: Rename OVERWRITE_ETHADDR_ONCE to
ENV_OVERWRITE_ETHADDR_ONCE")
u-boot/u-boot@5fb88fa725 ("env: Rename SYS_REDUNDAND_ENVIRONMENT to
ENV_REDUNDANT")
u-boot/u-boot@123682c765 ("env: Rename SYS_RELOC_GD_ENV_ADDR to
ENV_RELOC_GD_ENV_ADDR")
u-boot/u-boot@0f44d5549e ("env: Rename SYS_MMC_ENV_DEV to
ENV_MMC_DEVICE_INDEX")
u-boot/u-boot@31617b880a ("env: Rename SYS_MMC_ENV_PART to
ENV_MMC_EMMC_HW_PARTITION")
u-boot/u-boot@ffc4914703 ("env: Rename ENV_MMC_PARTITION to
ENV_MMC_SW_PARTITION")
u-boot/u-boot@fb5235239a ("env: Rename DEFAULT_ENV_FILE to
ENV_DEFAULT_ENV_TEXT_FILE")
(also renamed USE_DEFAULT_ENV_FILE to USE_ENV_DEFAULT_ENV_TEXT_FILE)
Remove upstreamed patches:
* 001-mtd-spinand-winbond-add-Winbond-W25N04KV-flash-suppo.patch
u-boot/u-boot@fe37fb8214
* 002-mtd-spinand-gigadevice-sync-supported-chips-with-lin.patch
u-boot/u-boot@506ceddffd
* 003-net-mediatek-correct-the-AN8855-TPID-value-in-port-i.patch
u-boot/u-boot@70db2be9fb
* 004-01-serial-mediatek-fix-register-names-and-offsets.patch
u-boot/u-boot@6e15d3f91a
* 004-02-serial-mediatek-enable-baudrate-accuracy-compensatio.patch
u-boot/u-boot@6952209ef2
* 005-clk-mediatek-add-dummy-clk-enable-disable-ops-for-ap.patch
u-boot/u-boot@1bf2121297
* 006-env-Fix-possible-out-of-bound-access-in-env_do_env_s.patch
u-boot/u-boot@0ffd456516
* 130-01-env-mtd-add-the-missing-put_mtd_device.patch
u-boot/u-boot@39ae954b04
* 130-02-env-mtd-initialize-saved_buf-pointer.patch
u-boot/u-boot@7e842bd331
* 170-cmd-bootmenu-permit-to-select-bootmenu-entry-with.patch
u-boot/u-boot@8c986521c3
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The u-boot of cmcc_rax3000m_*-ddr3 declares a dependency on
trusted-firmware-a-mt7981-*-ddr3-1866mhz, while actually packages
the normal BL2. This causes build failure if the the non-1866m
variant isn't built.
According to the previous commit, it's intended to use the lower
frequency variant to fix device stability issues. Correct
BL2_DDRTYPE as intended.
Fixes: 028050da69 ("mediatek: CMCC RAX3000Me: fix stability issues")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This commit fixes stability issues on certain RAX3000Me devices. Some
devices has DDR3 RAM which don't able to work reliably at 2133 MHz
and require special BL2 (1866 MHz RAM freq).
Fixes: https://github.com/openwrt/openwrt/issues/20046
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20059
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds ddr3 build for the ddr3 variant of the CMCC RAX3000Me
router.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19760
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update to the latest version.
Suppressed patch:
100-04-env-add-support-for-generic-MTD-device.patch[1]
[1] 03fb08d4ae
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Add an OpenWrt-based U-Boot build for this device, allowing for more
flexibility and customization.
Expected behaviour
------------------
When plugging the device, keeping the reset button pressed will enter
TFTP recovery mode: the board will send requests for the initramfs file
(openwrt-mediatek-filogic-glinet_gl-mt2500-initramfs-kernel.bin) from
IP 192.168.1.1 to 192.168.1.10 TFTP server.
The bootloader will populate the environment with the unit serial number
as reported by the "sn" value in eMMC, the "sn_bak" value, the country
code and ddns. WAN and LAN MAC addresses are reported in the environment
as well.
Limitations
-----------
No web interface is available, and only the LAN port can be used for
system recovery.
Notes
-----
This port has been tested with the Maxlinear version only, and with a
board that does not exhibit eMMC communication problems. Even though eMMC
frequency has been lowered, some testing is probably needed and always
very welcome.
A -factory image has been introduced, and is only needed when using the
"Load Firmware via TFTP then write to eMMC." boot menu function.
The device has not been converted to use uImage.FIT including the rootfs
to keep compatibility with stock bootloader and firmware.
Installation
------------
From a Linux root shell:
0. Transfer the needed files to the board, placing them in /tmp.
1. Make sure your U-Boot environment is erased: all of my units came with
unpopulated environment, but I am not sure this is always the case.
Issue the command
cat /dev/zero >/dev/mmcblk0p2
(you will get a "no space left" error, which is reasonable and expected).
2. Unlock the eMMC boot area where BL2 is located:
echo 0 >/sys/block/mmcblk0boot0/force_ro
3. Write the new BL2 code:
cat openwrt-mediatek-filogic-glinet_gl-mt2500-emmc-preloader.bin >/dev/mmcblk0boot0
4. Write new BL31+U-Boot image:
cat openwrt-mediatek-filogic-glinet_gl-mt2500-emmc-bl31-uboot.fip >/dev/mmcblk0p4
5. Reboot.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
This allows us to use the full size of nand, which increases ubi size
from 64M to 122.25M.
If you are at factory firmware, please refer commit 63b8d98dd0 ("mediatek: add support for Cudy TR3000 v1")
to boot into OpenWrt initramfs (stock layout).
Flash instructions:
1. Login into the device and backup everything, especially 'Factory' part.
1. Unlock mtd partitions:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
3. Write new BL2 and FIP
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Tested-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
SOC: MediaTek MT7981b
RAM: 256MB DDR3
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7981b DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Interface MAC Algorithm
LAN 8C:AE:DB:2C:xx:xx label
WAN 8C:AE:DB:2C:xx:xx label +1
WLAN 2.4G 8C:AE:DB:2C:xx:xx label +2
WLAN 5G 8C:AE:DB:2C:xx:xx label +3
Installation
-------------------Install openwrt image-------------------------------:
Set a static ip on the ethernet interface of your PC. (ip address:
192.168.1.254, subnet mask:255.255.255.0) .
Download the OpenWrt uboot image
(openwrt-mediatek-filogic-snr_cpe-ax2-bl31-uboot.fip).
SSH/SCP opened by default on the stock firmware (3.0.1).
Username: Admin, default password: Admin. Check it on the bottom of
the router.
Copy uboot image using SCP (WinSCP) to /tmp dir on SNR-CPE-AX2.
Download recovery file.
openwrt-mediatek-filogic-snr_snr-cpe-ax2-initramfs-recovery.itb.
Copy the recovery image to a TFTP server reachable at 192.168.1.254/24.
Open ssh shell to the SNR-CPE-AX2.
Run commands:
mtd write \
/tmp/openwrt-mediatek-filogic-snr_snr-cpe-ax2-bl31-uboot.fip FIP
reboot
Wait until recovery boot.
Open web 192.168.1.1 and do sysupgrade by
openwrt-mediatek-filogic-snr_cpe-ax2-squashfs-sysupgrade.itb
Signed-off-by: Nikolay March <palladin82@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/18700
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: M16U4G16256A DDR4 512MB
Ethernet: 2x 2.5G + 3x 1G
USB: 1x USB 3.0
WiFi1: MT7975N 2.4GHz 4T4R
WiFi2: MT7975PN 5GHz 4T4R
Button: Reset, WPS
Power: DC 12V 2A
Flash instructions:
Connect to the router using ssh or telnet,
username: useradmin, password is the web
login password of the router.
Use scp to upload bl31-uboot.fip and flash:
"mtd write xxx-bl31-uboot.fip FIP"
"mtd erase ubi"
Connect to the router via the Lan port,
set a static ip of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
Download initramfs image, reboot router,
waiting for tftp recovery to complete.
After openwrt boots up, perform sysupgrade.
Note:
Back up all mtd partitions before flashing.
Signed-off-by: Yujie Zhu <libriunc@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18138
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This PR adds support for netis NX31 router.
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM : 256 MiB DDR3
- Flash : SPI-NAND 128 MiB (ESMT)
- WLAN : MediaTek MT7976CN dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x3 (LAN, MediaTek MT7531AE)
10/100/1000 Mbps x1 (WAN, SoC internal phy)
- USB : No
- Buttons : Mesh, Reset
- LEDs : 1x Power (blue), unmanaged
1x Status (blue), gpio-controlled
1x WiFi 2.4 GHz (blue), gpio-controlled
1x WiFi 5 GHz (blue), gpio-controlled
3x LAN activity (blue), switch-controlled
1x WAN activity (blue), gpio-controlled
- Power : 12 VDC, 1 A
Installation
------------
1. Connect to the router using ssh (user: admin, pass: web interface
password)
2. Make mtd backup:
cat /dev/mtd0 | gzip -1 -c > /tmp/mtd0_spi0.0.bin.gz
cat /dev/mtd1 | gzip -1 -c > /tmp/mtd1_BL2.bin.gz
cat /dev/mtd2 | gzip -1 -c > /tmp/mtd2_u-boot-env.bin.gz
cat /dev/mtd3 | gzip -1 -c > /tmp/mtd3_Factory.bin.gz
cat /dev/mtd4 | gzip -1 -c > /tmp/mtd4_FIP.bin.gz
cat /dev/mtd5 | gzip -1 -c > /tmp/mtd5_ubi.bin.gz
3. Download mtd backup from the /tmp dir of the router to your PC using
scp protocol
4. Upload OpenWrt 'bl31-uboot.fip', 'preloader.bin' images to the /tmp
dir of the router using scp protocol
5. Write FIP and BL2 (replace bootloader):
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-bl31-uboot.fip FIP
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-preloader.bin BL2
6. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
7. Erase 'ubi' partition and reboot the router:
mtd erase ubi
reboot
8. U-Boot automatically boot OpenWrt recovery image from tftp server to
the RAM
9. Upload OpenWrt 'sysupgrade.itb' image to the /tmp dir of the router
(IP: 192.168.1.1) using scp protocol
10. Connect to the router using ssh and run:
sysupgrade -n openwrt-mediatek-filogic-netis_nx31-squashfs-sysupgrade.itb
Return to stock
---------------
1. Unpack stock BL2 and FIP partitions backup
2. Upload stock BL2 and FIP partitions backup to the /tmp dir of the
router using scp protocol
3. Connect to the router using ssh and run:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd unlock FIP
4. Restore backup:
mtd write /tmp/mtd4_FIP.bin FIP
mtd write /tmp/mtd1_BL2.bin BL2
5. Erase ubi and reboot:
mtd erase ubi
reboot
6. Power off the router
7. Press Reset button and power on the router. Release the button after
~10 sec
8. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware
Recovery
--------
1. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
2. Press “Reset” button and power on the router. After ~10 sec release
the button.
3. Use OpenWrt initramfs system for recovery
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | dc:xx:xx:d1:xx:18 | label |
| WAN | dc:xx:xx:d1:xx:1a | label+2 |
| WLAN 2g | de:xx:xx:11:xx:19 | |
| WLAN 5g | de:xx:xx:71:xx:19 | |
+---------+-------------------+-----------+
The LAN MAC was found in 'Factory', 0x1fef20
The WAN MAC was found in 'Factory', 0x1fef26
The WLAN 2g/5g MAC prototype was found in 'Factory', 0x4
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18324
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add U-Boot build for the ASUS ZenWiFi BT8 intended to replace the
stock loader.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This board is also as known as SuperElectron ZN-M5 and ZN-M8. However,
for ZN-M5 and ZN-M8, there's another version uses ZX279128 as CPU
chip, which is unsupported.
You can check it in "高级设置" > "系统日志" > "内核日志" page from webUI.
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS
Power: DC 12V 1A
Stock layout flash instructions:
Login into webUI and upload sysupgrade firmware in "系统管理" > "升级固件" page.
Remember to unselect "保留配置" ("Keep configurations") first before doing that.
OpenWrt U-Boot layout flash instructions:
1. Flash stock layout firmware first.
2. Connect to the device via SSH, and backup everything,
especially 'Factory' partition.
3. Unlock MTD partitions:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
4. Write new BL2 and FIP:
mtd write openwrt-mediatek-filogic-cmcc_a10-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cmcc_a10-ubootmod-bl31-uboot.fip FIP
5. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/18121
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove upstreamed patches:
010-menu-fix-the-logic-checking-whether-ESC-key-is-press.patch [1]
011-menu-add-support-to-check-if-menu-needs-to-be-reprin.patch [2]
012-bootmenu-add-reprint-check.patch [3]
Remove outdated patches:
455-arm-provide-noncached_set_region-prototype-to-fix-build.patch
Some patches have been manually rebased to match the upstream
changes. This patch also fixes the dtc warning for reserved-memory
dts node. If #address-cells and #size-cells are not same as the
root node definitions, the dtc will complain about it.
All defconfigs are refreshed by `make "$board"_defconfig` and
`make savedefconfig`.
[1] ddac69885e
[2] ccdd7948e2
[3] 599652cff1
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Add U-Boot replacement loader for the MERCUSYS MR90X. This is required
to increase available flash space in OpenWrt.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16744
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The GatoNetworks GDSP is a re-branded version of the R5000 5G Industrial
router from Yinghua Technologies.
Advantages over stock bootloader:
1. supports serving the external GPIO WDT, allowing for easier work in U-Boot
shell
2. supports cool features like netconsole, easy recovery, scripting and so on
3. allows using FIT image and image integrity validation
and ultimately gives you much more flexibility to implement your tweaks.
Known issues
------------
To make it easier to operate the device, console I/O multiplexing support has
been enabled in U-Boot configuration. Setting I/O related U-Boot environment
variables to something like "serial,nc" will have the desired effect. Still,
setting these variables to such a value in the persistent environment will
lead to a crash and make it impossible to boot the system or recover it. I
decided to leave it on anyway since I think it can be very practical in
development.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Using the arrow keys to navigate the U-Boot menu often leads to being
dropped into the U-Boot shell unexpectedly.
This can be prevented in most cases by improving the logic to detect the
arrow key ESC sequence and only reprinting the menu if actually needed.
Also enable CONFIG_SERIAL_RX_BUFFER for all boards as it helps preventing
the remaining cases.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add u-boot support based on the kernel dts introduced in d1016446 and
the GL-MT6000 u-boot support in fe10f974.
The pcie-mediatek-gen3 kernel driver doesn't like hotplug, so to work in
PCIe mode, the 5G modem on this device needs to be switched on by u-boot
before starting the kernel. Include an init_modem step in the boot_system
action to set the relevant gpios. (The factory bootloader does the same,
using Mediatek SDK-specific gpio_power_clr and gpio_pull_up.)
Ideally the modem would be started using gpio-hog in the device tree, but
this will need to wait until mediatek gpio-hog support is fixed upstream:
https://lore.kernel.org/u-boot/6ef2583e85eea60560d7776377d662779e7c44e5.1722419839.git.chris@arachsys.com/
The bootloader can be replaced using the built-in web interface of the
factory bootloader. Hold the reset button for five seconds while powering
on the device and it will boot into a recovery http server.
http://192.168.1.1/uboot.html and http://192.168.1.1/bl2.html can then
be used to upload openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip
and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin respectively.
Alternatively, from a root shell on the running system, unlock the boot
partition with
echo 0 >/sys/block/mmcblk0boot0/force_ro
then write openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip to
/dev/mmcblk0p4 and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin
to /dev/mmcblk0boot0.
Signed-off-by: Chris Webb <chris@arachsys.com>
Link: https://github.com/openwrt/openwrt/pull/15645
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Same as TP-Link TL-XDR608x, this router comes with locked vendor
loader. Add U-Boot build for replacement loader for this device.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15930
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Decode and uncompress the configuration:
* Enter fakeroot if you are not login as root.
base64 -d e-xxxxxxxxxxxx-cfg.tar.gz | tar -zx
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; /usr/sbin/telnetd; ) &
5. Repack the configuration:
tar -zc etc/ | base64 > e-xxxxxxxxxxxx-cfg.tar.gz
6. Upload new configuration via web interface, now you can connect to
ASR3000 via telnet.
Flash instructions:
1. Connect to ASR3000, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-abt_asr3000-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-abt_asr3000-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15887
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
1. Rename function _do_env_set() to env_do_env_set().
2. Replace kwbimage hack with UBOOT_CUSTOMIZE_CONFIG:
"--disable TOOLS_KWBIMAGE" and "--disable TOOLS_LIBCRYPTO".
3. Disable CONFIG_CMD_BOOTEFI_BOOTMGR for all supported devices
because the newly added UEFI bootmenu entries doesn't work.
4. Enable CONFIG_VERSION_VARIABLE for the OpenWrt One.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Co-authored-by: Daniel Golle <daniel@makrotopia.org>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS/Mesh
Power: DC 12V 1A
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Download the configration utilities:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
These binaries are extraced from the factory firmware, which are
dynamically linked with aarch64 musl 1.1.24. To use them, you
must run them under the same runtime environment, otherwise the
binaries will not work properly!
3. Upload the configuration and utilities to a suitable environment.
4. Uncompress the utilities, move them to '/bin' and give them executable permisison:
tar -zxf openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
mv mkconfig seama /bin
chmod +x /bin/mkconfig
chmod +x /bin/seama
5. Decrypt and uncompress the configuration:
Enter fakeroot if you are not login as root.
mkconfig -a de-enca -m EA0326GMP_3FE79221BAAA -i EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz -o backup.tar.gz
tar -zxf backup.tar.gz
6. Edit 'etc/config/dropbear', set 'enable' to '1'.
7. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
8. Repack the configuration:
tar -zcf backup.tar.gz etc/
mkconfig -a enca -m EA0326GMP_3FE79221BAAA -i backup.tar.gz -o EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz
9. Upload new configuration via web interface, now you can SSH to EA0326GMP.
A minimum configuration which enabled SSH access is also provided
to simplify the process:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-enable-ssh.tar.gz
Flash instructions:
1. SSH to EA0326GMP, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-nokia_ea0326gmp-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-nokia_ea0326gmp-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
This adds support for the bpi-r4 variant with internal 2.5G PHY and
additional ethernet port instead of second sfp.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Add support for Xiaomi Redmi AX6S to be used as a second-stage
UBI loader.
The defconfig/env is minimal: Boot fit from UBI. If that failed,
load and boot initramfs image from TFTP.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
It should be "BananaPi BPi-R3 Mini" instead of just "BananaPi BPi-R3".
Fixes: bc25519f98 ("uboot-mediatek: add builds for BananaPi BPi-R3 mini")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The R3 mini comes with two Airoha EN8811H PHYs for 2.5G Ethernet.
The driver added to U-Boot expects the firmware for the PHY to be
stored inside UBI volume en8811h-fw or MMC boot1 hardware partition.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Move fip and factory into UBI static volumes.
Use fitblk instead of partition parser.
!! RUN INSTALLER FIRST !!
Existing users of previous OpenWrt releases or snapshot builds will
have to **re-run the updated installer** before upgrading to firmware
after this commit.
DO NOT flash or run even just the initramfs image unless you have
run the updated installer which moves the content of the 'factory'
partition into a UBI volume.
tl;dr: DON'T USE YET!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Modernize bootloader and flash memory layout of the BPi-R64 similar to
how it has also been done for the BPi-R3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Modernize U-Boot to provide a better reference:
* store fip image in UBI now that TF-A supports that
* switch from uImage.FIT partition parser to new fitblk
virtual firmware block driver (root=/dev/fit0)
* automatically set root device according to boot_mode register
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rebase local patches on top of quarterly timed release, allowing to
drop numerous patches which have been accepted upstream since the
release of U-Boot 2023.07.02.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add basic U-Boot drop-in replacement compatible with the flash layout
of the vendor loader of the Zbtlink WG3526 (16M) MT7621 router board.
The idea here is a to have a reference build of uboot-mediatek also for
a simple MIPS boards more popular than MT7621 RFB.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
