This device has only half the flash and ram of the RBR20. It also has
two lan ports instead of wan and lan.
Hardware
--------
SOC: Qualcomm IPQ4019
FLASH: 128MB (Winbond W29N01HVSINF)
RAM: 256MB (Winbond W632GU6MB-12)
WIFI: Qualcomm IPQ4019
Qualcomm Atheros QCA9886
ETH: 2x LAN
LED: 5 (4 RGB at top, 1 RG at back)
BTN: WPS, Reset
UART: 115200 8N1 (dotted Pin = VCC) VCC-TX-RX-GND
MAC addresses
-------------
LAN Label MAC (stored in boarddata1 offset 0x0)
2.4G LAN
5GLow LAN + 3 (stored in boarddata1 offset 0xc)
5GUpper LAN + 2 (stored in boarddata1 offset 0x12)
Installation
------------
Either use the vendor ui upgrade method or nmrpflash to install the
factory image.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20560
Signed-off-by: Robert Marko <robimarko@gmail.com>
This device shares a lot of similarities with the LBR20 - the RBR20 just
misses the LTE modem and its formfactor is alot smaller. Other than that
the LED configuration matches other RBR devices but the RBR20 has less
LEDs than its larger counterparts.
Hardware
--------
SOC: Qualcomm IPQ4019
FLASH: 256MB (Winbond W29N02GVSIAF)
RAM: 512MB (Nanya NT5CC256M16EP-EK)
WIFI: Qualcomm IPQ4019
Qualcomm Atheros QCA9886
ETH: 1x WAN, 1x LAN
LED: 5 (4 RGB at top, 1 RG at back)
BTN: WPS, Reset
UART: 115200 8N1 (dotted Pin = VCC) VCC-TX-RX-GND
MAC addresses
-------------
LAN Label MAC (stored in boarddata1 offset 0x0)
WAN LAN + 1 (stored in boarddata1 offset 0x6)
2.4G LAN
5GLow LAN + 3 (stored in boarddata1 offset 0xc)
5GUpper LAN + 2 (stored in boarddata1 offset 0x12)
Installation
------------
Either use the vendor ui upgrade method or nmrpflash to install the
factory image.
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20560
Signed-off-by: Robert Marko <robimarko@gmail.com>
fa62f8a2885c ipq8074: add BDF for Zyxel NWA210AX
7c6b7545f69a qca4019: qca9888: add bdfs for Netgear RBK20
Signed-off-by: Robert Marko <robimarko@gmail.com>
This handles the case when 'wpad' or 'wpad-mini' package is used which is
missing WPA3 support. This makes it impossible to use ucode wifi-scripts
on such APs as it will raise an error:
daemon.err hostapd: Line 87: unknown configuration item 'sae_password_file'
This also achieves parity with what is currently happening with old wifi-scripts.
The behavior now matches.
Fixes: https://github.com/openwrt/openwrt/issues/20781
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/20784
Signed-off-by: Robert Marko <robimarko@gmail.com>
$ git log --no-merges --pretty=oneline --abbrev-commit 20251021..20251111
fcf22f50 rtl_bt: Update RTL8922A BT USB firmware to 0x41C0_C905
c0af6c70 linux-firmware: add firmware for mt7987 internal 2.5G ethernet phy
a50c068b rtw88: 8822b: Update firmware to v30.20.0
e5606bd7 rtl_nic: add firmware rtl8125k-1
c5831f31 ASoC: tas2781: Update dsp firmware for HP and ASUS projects
ad907cca Revert "Merge branch 'robot/patch-0-1762671757' into 'main'"
d665e29c ASoC: tas2781: Update dsp firmware for HP and ASUS projects
213080ae amdgpu: DMCUB updates for various ASICs
23cf7dbb amdgpu: DMCUB updates for various ASICs
95cd295e qcom: add SOCCP firmware for kaanapali platform
9444af1a xe: Update GUC to v70.53.0 for BMG, LNL, PTL
f2a23165 i915: Update GUC to v70.53.0 for DG2, MTL
4dedd6cb rtw89: 8851b: update fw to v0.29.41.5
84cc37f3 rtw89: 8852b: update fw to v0.29.128.0 with format suffix -2
3ab5b9e5 rtw89: 8852b: update fw to v0.29.29.14
1b1c14bb Revert "rtw89: 8852b: update fw to v0.29.128.0"
9a0d0ed6 rtw89: 8852bt: update fw to v0.29.127.0 with format suffix -1
be71e790 rtw89: 8852bt: update fw to v0.29.122.1
b6252a03 Revert "rtw89: 8852bt: update fw to v0.29.127.0"
a976b0aa linux-firmware: Update firmware file for Intel BlazarU core
5a689a2f linux-firmware: Update firmware file for Intel BlazarI core
77425784 linux-firmware: Create audio folder in ti folder, and move all the audio firmwares into it
e189b618 amdgpu: DMCUB updates for various ASICs
646d97f5 linux-firmware: Update WHENCE for microcode_amd_fam19h.bin
e637542f linux-firmware: Update AMD cpu microcode
0fc31ad6 linux-firmware: update firmware for MT7925 WiFi device
b63c322f mediatek MT7925: update bluetooth firmware to 20251015213201
35e54243 rtl_bt: Add firmware and config files for RTL8761CUV
ad915447 linux-firmware: Update AMD cpu microcode
7bcedf5c qcom: add ADSP firmware for kaanapali platform
728e9243 amdgpu: DMCUB updates for various ASICs
05105d24 linux-firmware: Renaming the file to cover a wide range of HP Lunar Lake system.
b582532d mediatek MT7920: update bluetooth firmware to 20251020151255
33d0511d linux-firmware: update firmware for MT7922 WiFi device
c2087f88 linux-firmware: update firmware for MT7920 WiFi device
3a49a735 amd-ucode: Fix minimum revisions in README
0de0cd7f cirrus: cs35l41: Rename various Asus Laptop firmware files to not have Speaker ID
93c92978 mediatek MT7922: update bluetooth firmware to 20251020143443
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Only set rsn_override_key_mgmt when rsn_override is enabled.
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When encryption is set to 'sae' without explicit pairwise cipher in
non-HE/EHT mode, both the main RSNE and override RSNE would advertise
identical parameters (SAE+CCMP+MFP=2), adding unnecessary overhead.
Check that the pairwise ciphers differ before enabling override. This
preserves the intended behavior for HE/EHT modes (GCMP-256+CCMP vs CCMP)
while avoiding pointless override IEs.
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The function was using phydev.name (e.g., "phy0.0") instead of
phydev.phy (e.g., "phy0") when calling wpa_supplicant.phy_set_macaddr_list.
This is inconsistent with all other wpa_supplicant ubus calls in the same
file which correctly use phydev.phy.
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When an MLO interface specifies multiple radios and the first radio
is disabled, the MLO configuration was never created because the code
only attempted to create it when processing the first device in the
list (which gets skipped if disabled).
Fix by creating the MLO config for the first enabled device instead
of only when processing dev_names[0].
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Assign the address at wdev create time, similar to legacy interfaces.
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ensure that the 4addr flag is passed to phy.wdev_add.
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
CMCC PZ-L8 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on IPQ5000.
Specifications:
- SoC : Qualcomm IPQ5000
- RAM : Integrated 256MiB DDR3L
- Flash : 128 MiB SPI-NAND (ESMT F50D1G41LB)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm IPQ5000 (SoC)
- 5 GHz : Qualcomm Atheros QCN6102
- Ethernet : 4x 10/100/1000 Mbps
- switch : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO) : 2x LEDs, 2x Keys
- UART : Through-hole on PCB, 4pins in the middle of the black aluminum heat sink
- assignment : 3.3V, GND,TX, RX (from left to right)
- settings : 115200n8
- Power : 12 VDC, 1 A
Flashing Instructions:
1. SSH Method
(1) Enable SSH on the stock firmware
a. Version 501.8 and 501.9:
Log in to http://192.168.10.1 with the password on the sticker
Append "/admin/system/admin" to the URL and press Enter
Delete "Dropbear instance", click "Add instance", then "Save and Apply"
Reboot the router
b. Version 501.11 and 501.12:
While the router is running the stock firmware, press and hold the reset button for 20-30 seconds
Open http://192.168.10.1:56781 and login with username "root" and the password on the sticker
Run "vi /etc/config/dropbear" and delete the line "option enable '0'"
Reboot the router
(2) Upload the factory.ubi file to router's /tmp directory (using scp or wget)
and execute the following commands in the router's shell
export rootfs=$(cat /proc/mtd | grep rootfs | grep -v _ | cut -d: -f1)
ubidetach -f -p /dev/${rootfs}
ubiformat /dev/${rootfs} -y -f /tmp/factory.ubi
2. U-Boot Method using UBI Image
Place the factory.ubi file on your TFTP server, enter U-Boot CLI and exec these commands
tftpboot <your_tftp_server_ip>:factory.ubi
flash rootfs
reset
3. U-Boot Method using initramfs Image
(1) Place the openwrt-*-initramfs-fit-uImage.itb file on your TFTP server
and rename it to initramfs.bin
(2) Enable serial console, enter to U-Boot CLI and exec these commands
tftpboot <your_tftp_server_ip>:initramfs.bin
bootm
(3) Once boot completed, upload the sysupgrade.bin file to router's /tmp directory
(using scp or wget) and execute the following command in openwrt shell
sysupgrade -n /tmp/sysupgrade.bin
Switching to the Stock Firmware:
Please follow the commit 3b7d72bc2e
Partition Layout (Stock Firmware):
0x000000000000-0x000000080000 : "0:SBL1"
0x000000080000-0x000000100000 : "0:MIBIB"
0x000000100000-0x000000140000 : "0:BOOTCONFIG"
0x000000140000-0x000000180000 : "0:BOOTCONFIG1"
0x000000180000-0x000000280000 : "0:QSEE"
0x000000280000-0x000000380000 : "0:QSEE_1"
0x000000380000-0x0000003c0000 : "0:DEVCFG"
0x0000003c0000-0x000000400000 : "0:DEVCFG_1"
0x000000400000-0x000000440000 : "0:CDT"
0x000000440000-0x000000480000 : "0:CDT_1"
0x000000480000-0x000000500000 : "0:APPSBLENV"
0x000000500000-0x000000640000 : "0:APPSBL"
0x000000640000-0x000000780000 : "0:APPSBL_1"
0x000000780000-0x000000880000 : "0:ART"
0x000000880000-0x000000900000 : "0:TRAINING"
0x000000900000-0x000004300000 : "rootfs"
0x000004300000-0x000007d00000 : "rootfs_1"
Notes:
This device is almost the same as ELECOM WRC-X3000GS2, including partition layout and the dual-boot feature.
Known Issues:
- All Wi-Fi related peripherals are disabled in device tree, since 256 MiB RAM is too few for ath11k.
- This device has another version with nand flash FM25SL01, which is not supported at the moment.
https://github.com/immortalwrt/immortalwrt/blob/master/target/linux/mediatek/patches-6.12/342-mtd-spinand-Support-fmsh.patch
MAC Addresses:
Interface MAC Address Location (binary)
LAN A4:39:B6:xx:xx:9D (0:ART, 0x00-0x05)
WAN A4:39:B6:xx:xx:9E (0:ART, 0x06-0x0B)
2.4 GHz A4:39:B6:xx:xx:9F (0:ART, 0x0C-0x11)
5 GHz A4:39:B6:xx:xx:A0 (0:ART, 0x12-0x17)
Signed-off-by: Chang Liu <jssqliuchang@gmail.com>
When using wpad-openssl/wpad-basic-openssl, wpa_supplicant/hostapd may not be ready because of openssl.
This cause supplicant.setup and hostapd.setup to be failed.
Therefore, wait for wpa_supplicant/hostapd to be ready before supplicant.setup and hostapd.setup.
Run-tested: mediatek/filogic GL-MT3000
fixes: #20361
Signed-off-by: Andy Chiang <AndyChiang_git@outlook.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use stationary_ap configuration for 6GHz AX AP (not only BE).
This change fixes the 6GHz network not visible issue for QCN9024.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
313f344d8436 dlink-sge-image: add support for D-Link DIR-X1860 B1/DIR-X1550 A1
ac7a4abdde7d iptime-crc32: add support for ipTIME AX3000SE
c42a3bc53da8 iptime-crc32: add support for ipTIME AX2002MESH
Link: https://github.com/openwrt/openwrt/pull/20734
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
New Packages / build options:
* sound-midi2: enable MIDI 2.0 / UMP in ALSA MIDI
* sound-midi2-seq: enable MIDI 2.0 / UMP in ALSA sequencer
* sound-midi2-usb: enable USB MIDI 2.0 support
* sound-dynamic-minors: allow more than 8 MIDI devices
More info about ALSA MIDI 2.0:
https://docs.kernel.org/6.12/sound/designs/midi-2.0.html
More info about MIDI 2.0:
https://midi.org/midi-2-0
Signed-off-by: Florian Bomers <github@bome.com>
Link: https://github.com/openwrt/openwrt/pull/20727
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Make it a little bit more consistant, and a bit more idiomatic.
Signed-off-by: David Härdeman <david@hardeman.nu>
Link: https://github.com/openwrt/openwrt/pull/20673
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The support has been removed from odhcpd, so remove the Makefile options
related to homenet.
Signed-off-by: David Härdeman <david@hardeman.nu>
Link: https://github.com/openwrt/openwrt/pull/20673
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
"system" is used to get the current time zone, "network" is used to get
the global DUID.
Signed-off-by: David Härdeman <david@hardeman.nu>
Link: https://github.com/openwrt/openwrt/pull/20673
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Support for this option has been removed from odhcpd, so remove it in
the defaults as well.
Signed-off-by: David Härdeman <david@hardeman.nu>
Link: https://github.com/openwrt/openwrt/pull/20673
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This exands the list of AKMs to display:
- display the hash when larger than the default (loosely based on
what hostapd uses in config).
- renaming 'WPA PSK2' to 'WPA PSK-SHA256' as a result
- separate FILS suites from plain 802.1x
- add suites 3, 5, 9, 19, 20, 24, and 25
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20686
Signed-off-by: Robert Marko <robimarko@gmail.com>
Escape control characters when displaying ESSID. It is not uncommon for
a scan to encounter invalid SSIDs, containing binary data. Escape the
control characters to avoid messing the display (ENQ is particularly
bothersome).
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20686
Signed-off-by: Robert Marko <robimarko@gmail.com>
This adds the ESSID: line to the iwinfo scan results.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20686
Signed-off-by: Robert Marko <robimarko@gmail.com>
Swig 4.3.0 has changed SWIG_Python_AppendOutput, which now requires an
additional parameter `is_void`. SWIG_AppendOutput remains unchanged.
This was fixed upstream in u-boot/u-boot@a63456b
```
scripts/dtc/pylibfdt/libfdt_wrap.c: In function ‘_wrap_fdt_next_node’:
scripts/dtc/pylibfdt/libfdt_wrap.c:5581:17: error: too few arguments to function ‘SWIG_Python_AppendOutput’
5581 | resultobj = SWIG_Python_AppendOutput(resultobj, val);
| ^~~~~~~~~~~~~~~~~~~~~~~~
```
This is the same fix as applied in 363e07d.
Fixes: #20619
Link: #20620
Signed-off-by: Trix Taiclet <trix@c3l.lu>
Link: https://github.com/openwrt/openwrt/pull/20620
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for TP-LINK BE450.
Device specification
--------------------
SoC Type: MediaTek MT7988D, Cortex-A73, 64-bit
RAM: 512MB
Flash: SPI NAND GigaDevice (128 MiB)
Ethernet: MediaTek MT7531AE (3 Ports) + 2.5GbE (internal MT7988 phy) + 10GbE (RTL8261N)
WLAN: MT7992
WLAN 2g: MediaTek MT7975N, b/g/n/ax/be, MIMO 4x4
WLAN 5g: MediaTek MT7979N, a/n/ac/ax/be, MIMO 4x4
LEDs: 8 LEDs, 1 status blue, 2x WIFI blue, 2x Internet
blue/orange, 1 LAN blue, 1 usb blue, 1 wps blue, gpio-controlled
Button: 2 (Reset, WPS)
USB port: Yes
Power: 12 VDC, 2 A
Connector: Barrel
Bootloader: Main U-Boot - U-Boot 2023.10-rc4. Additionally, ubi0
partition contain "seconduboot" (also U-Boot 2023.10-rc4)
Serial console (UART), unpopulated, located near the power connector
---------------------
heatsink
| |
| |
| | +----+-----+------+-------+ +-----------------+
| | | TX | RX | GND | +3.3V | | power connector |
+---+ +----+-----+------+-------+ +-----------------+
|
Don't connect ----+
Disassemble: rm the 2 screws at the bottom and the one at the backside.
un-clip the case starting at the edge above the LEDs.
Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
tftpboot 0x50000000 openwrt-mediatek-filogic-tplink_be450-initramfs-kernel.bin && bootm 0x50000000
4. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Note: the 10GbE (RTL8261N) is only working if reverting this Realtek target specific commit:
b77fa45d12
The second ubi partition (ubi1) is empty and there is no known
dual-partition mechanism, neither in u-boot nor in the stock firmware.
NMBM is not used.
Not Working: WED, if activated, MT7992 isn't recognized any more.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Link: https://github.com/openwrt/openwrt/pull/20398
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
e51d568 wireless-regdb: update regulatory rules for Botswana (BW) for 2022
5afc632 wireless-regdb: update regulatory rules for Sint Marteen (SX) for 2018
b484a31 wireless-regdb: Update regulatory info including bandwidth for Costa Rica (CR) for 2023
39e5e04 wireless-regdb: Permit lower 6 GHz band for Kazakhstan (KZ)
a827d3a wireless-regdb: update regulatory database based on preceding changes
Link: https://github.com/openwrt/openwrt/pull/20544
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This version fixes multiple security problems:
CVE-2025-7395: Problem in certificate verification on Apple devices
CVE-2025-7394: Predictable results from RAND_bytes() after fork call in OpenSSL compatibility layer
CVE-2025-7396: Activate Curve25519 blinding support
See Release notes:
https://github.com/wolfSSL/wolfssl/releases/tag/v5.8.0-stablehttps://github.com/wolfSSL/wolfssl/releases/tag/v5.8.2-stable
wolfSSL is now GPLv3 instead of GPLv2, see:
629c5b4cf6
The file size increased a bit:
```
546060 bin/packages/mipsel_24kc/base/libwolfssl5.7.6.e624513f-5.7.6-r1.apk
560684 bin/packages/mipsel_24kc/base/libwolfssl5.8.2.e624513f-5.8.2-r1.apk
```
Link: https://github.com/openwrt/openwrt/pull/20547
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
See announcement mail for list of new features:
https://lists.infradead.org/pipermail/linux-mtd/2025-February/108248.html
Cherry pick some upstream commits which fix build problems in some
situations.
autoreconf fixup is needed now otherwise the build fails with:
```
mtd-utils-2.3.0/missing: line 81: automake-1.16: command not found
```
The code in tests/ubifs_tools-tests/Makemodule.am does not build because
some test data is not packaged in the tar files, do not build code from
this directory.
The size increased only very little:
61498 bin/targets/ramips/mt7621/packages/nand-utils-2.3.0-r1.apk
101643 bin/targets/ramips/mt7621/packages/ubi-utils-2.3.0-r1.apk
61243 bin/targets/ramips/mt7621/packages/nand-utils-2.2.1-r1.apk
101291 bin/targets/ramips/mt7621/packages/ubi-utils-2.2.1-r1.apk
Link: https://github.com/openwrt/openwrt/pull/20540
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
d1fac9ec trace-cmd record: Always disable func_stack_trace in tracecmd_disable_all_tracing()
75e3b868 trace-cmd: utest: include libgen.h for POSIX basename()
176bc1f1 trace-cmd record: Fix compression when files are greater than 2GB
9da3427e trace-cmd lib: Use proper printf format specifiers
5f20c477 trace-cmd: Version 3.3.1
39acb4cc trace-cmd list: Use tracefs_filter_functions()
4eef18ff trace-cmd show: Add --max_latency
e4540079 trace-cmd list: Use tracefs_instances() to list instances
908d122e trace-cmd stat: Use tracefs_instances() instead of walking them
cc6de736 trace-cmd reset: Bail out immediately if user provides an invalid option
3c4fd59b trace-cmd reset: Add option to preserve specific dynamic events
19ceba14 trace-cmd reset: Update man page for -k option
bbea061f trace-cmd reset: Add bash tab completion for -B and -k
7f126040 trace-cmd utest: Add test cases for trace-cmd reset
5e8b3c16 trace-cmd lib: Prevent a memory leak in handle_options()
6295bcc1 trace-cmd record: Prevent a memory leak in show_error()
7abca575 trace-cmd lib: Check the return value of do_lseek() in trace_get_options()
22a1605c trace-cmd dump: Prevent buffer overrun in dump_clock()
52946308 trace-cmd record: Prevent memory leak in setup_network()
1b901134 trace-cmd lib: Prevent memory leak in tracecmd_create_event_hook()
59d2c3f9 trace-cmd mem: Prevent a memory leak in trace_mem()
969c36d2 trace-cmd record: Check the length of the protocol version received
201f95fd trace-cmd sqlhist: Fix missing initialization of a var
f10d39b8 trace-cmd .gitignore: Ignore utest/trace-utest in git
c76f2404 trace-cmd: Prevent buffer overflow in update_pid_filters()
db45fec2 trace-cmd: libtracecmd: Rename private functions to fix static building
d6cdfc23 trace-cmd: libtracecmd: Remove some unneeded line breaks
d14d790a trace-cmd lib: Prevent a memory leak in tracecmd_tsync_with_guest()
b948fbed trace-cmd lib: Prevent memory leak in tracecmd_msg_wait_for_cmd()
a1b5eee6 trace-cmd sqlhist: Initialize name in trace_sqlhist()
fee20bfb trace-cmd: Fix memory leak in stop_mapping_vcpus()
5f1eeba9 trace-cmd record: Fix stdin redirection to /dev/null
a1b8a0f5 trace-cmd meson: Add options for doc and utest build
24eed8d8 trace-cmd lib: Prevent a leaked FD in __tracecmd_create_buffer_recorder()
d6241881 trace-cmd sqlhist: Initialize err value to tracefs_sql()
179125a4 trace-cmd documentation: Fix typo in man of trace-cmd attach
e81cd4e3 trace-cmd lib: Copy message buffer content in get_trace_req_args()
b44a9a9f trace-cmd list: Check if any functions were found
9c44659e trace-cmd: Add trace-cmd set to bash completion (like start)
f4ede17d trace-cmd list: Show events in bash completion
2149da9c trace-cmd: Add sqlhist to bash completion
477bf923 trace-cmd: Install completion script in /usr/share/bash-completion/completions
6448ea34 trace-cmd show: Update help message for --hist and --trigger options
2fbeb317 trace-cmd list: Show all functions that match string by default
f339229f trace-cmd record: Fix compression on big-endian systems
e57b3d3e libtracecmd: Add missing error handling to trace-compress.c
b1db6f61 libtracecmd: Version 1.5.3
d0a17b4f trace-cmd: Version 3.3.2
24cdb0be trace-cmd completion: Fix trace-cmd report to show files
68bd953b trace-cmd: libtrace-cmd: Fix glob() return value checks
2d5c06e6 trace-cmd: record: Fix glob() return value checks
2c46eb6b trace-cmd split: Only open one file descriptor per CPU
9da7e594 trace-cmd: Version 3.3.3
Link: https://github.com/openwrt/openwrt/pull/20548
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
