forked from mirror/openwrt
qualcommax: ipq807x: add support for TCL LINKHUB HH500V
TCL LINKHUB HH500V also known as Vodafone Gigacube B157 is a dual band 802.11ax 5G NR CPE with an FXS port. Specifications: * SoC: Qualcomm IPQ8072A * RAM: 1024 MB * NAND flash: 256MB NAND (MT29F2G08ABBGAH4) * NOR flash: 64MB NOR (MX25U25635F) - only in some variants * WiFi 5G: Qualcomm QCN5054 * WiFi 2.4G: Qualcomm QCN5024 * Ethernet 2.5G: Qualcomm QCA8081 * Ethernet 1G: Qualcomm QCA8075 * Modem: GosunCn GM800 (Qualcomm Snapdragon X55) * SIM: 1 nano-SIM card slot * Buttons: Power, Reset, WPS * LEDs: Power (B/R), WiFi (B), 4G (B/Y/R), 5G (B/Y/R) * VoIP: 1 FXS RJ11 port (not supported in OpenWrt) * Power: 12V, 3A UART serial console: * 115200,8N1,1.8V * Three unmarked test points next to QJ2012A: +---------+ | QJ2012A | +---------+ o TX o GND o RX o o o Installation via OEM firmware: * Use the following process to obtain root ssh access https://forum.openwrt.org/t/150371/24 * Connect using root with no password on port 42000 * Optionally for serial bootloader access run : fw_setenv bootdelay=3 * SCP factory.bin to /tmp * Run: sysupgrade -n /tmp/factory.bin Installation via serial console and OEM firmware:: * Use console to access OEM firmware shell * Proceed with SCP & sysupgrade as described above Other notes: * This device uses active partition rotation * Some versions (TCL branded?) have a NOR chip in addition to NAND * The above is supported by u-boot patching DT partitions * DT patching does NOT occur on tftpboot/bootm * Modem is detected as foxconn-sdx55 by kernel (same VID/PID) * This works OK-ish and should be improved if we can get OEM modem details Signed-off-by: Milan Krstic <milan.krstic@gmail.com> Link: https://github.com/openwrt/openwrt/pull/19182 Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit is contained in:
Milan Krstic
Robert Marko
parent
8dd1be5f7b
commit
ac8b5526bc
11 changed files with 572 additions and 0 deletions
|
|
@ -7,6 +7,25 @@ touch /etc/config/ubootenv
|
|||
|
||||
board=$(board_name)
|
||||
|
||||
ubootenv_mtdinfo () {
|
||||
UBOOTENV_PART=$(cat /proc/mtd | grep -i APPSBLENV)
|
||||
mtd_dev=$(echo $UBOOTENV_PART | awk '{print $1}' | sed 's/:$//')
|
||||
mtd_size=$(echo $UBOOTENV_PART | awk '{print "0x"$2}')
|
||||
mtd_erase=$(echo $UBOOTENV_PART | awk '{print "0x"$3}')
|
||||
nor_flash=$(find /sys/bus/spi/devices/*/mtd -name ${mtd_dev})
|
||||
|
||||
if [ -n "$nor_flash" ]; then
|
||||
ubootenv_size=$mtd_size
|
||||
else
|
||||
# size is fixed to 0x40000 in u-boot
|
||||
ubootenv_size=0x40000
|
||||
fi
|
||||
|
||||
sectors=$(( $ubootenv_size / $mtd_erase ))
|
||||
sectors=$(printf "0x%x" $sectors )
|
||||
echo /dev/$mtd_dev 0x0 $ubootenv_size $mtd_erase $sectors
|
||||
}
|
||||
|
||||
case "$board" in
|
||||
aliyun,ap8220|\
|
||||
compex,wpq873|\
|
||||
|
|
@ -58,6 +77,9 @@ xiaomi,ax9000)
|
|||
spectrum,sax1v1k)
|
||||
ubootenv_add_mmc "0:APPSBLENV" "" "0x0" "0x40000" "0x40000" "1"
|
||||
;;
|
||||
tcl,linkhub-hh500v)
|
||||
ubootenv_add_uci_config $(ubootenv_mtdinfo)
|
||||
;;
|
||||
esac
|
||||
|
||||
config_load ubootenv
|
||||
|
|
|
|||
|
|
@ -81,6 +81,7 @@ ALLWIFIBOARDS:= \
|
|||
redmi_ax6 \
|
||||
skspruce_wia3300-20 \
|
||||
spectrum_sax1v1k \
|
||||
tcl_linkhub-hh500v \
|
||||
tplink_deco-x80-5g \
|
||||
tplink_eap610-outdoor \
|
||||
tplink_eap620hd-v1 \
|
||||
|
|
@ -267,6 +268,7 @@ $(eval $(call generate-ipq-wifi-package,prpl_haze,prpl Haze))
|
|||
$(eval $(call generate-ipq-wifi-package,redmi_ax6,Redmi AX6))
|
||||
$(eval $(call generate-ipq-wifi-package,skspruce_wia3300-20,SKSpruce WIA3300-20))
|
||||
$(eval $(call generate-ipq-wifi-package,spectrum_sax1v1k,Spectrum SAX1V1K))
|
||||
$(eval $(call generate-ipq-wifi-package,tcl_linkhub-hh500v,TCL LINKHUB HH500V))
|
||||
$(eval $(call generate-ipq-wifi-package,tplink_deco-x80-5g,TP-Link Deco X80-5G))
|
||||
$(eval $(call generate-ipq-wifi-package,tplink_eap610-outdoor,TPLink EAP610-Outdoor))
|
||||
$(eval $(call generate-ipq-wifi-package,tplink_eap620hd-v1,TP-Link EAP620 HD v1))
|
||||
|
|
|
|||
|
|
@ -358,6 +358,7 @@ CONFIG_PHY_QCOM_QUSB2=y
|
|||
# CONFIG_PHY_QCOM_USB_SNPS_FEMTO_V2 is not set
|
||||
# CONFIG_PHY_QCOM_USB_SS is not set
|
||||
CONFIG_PINCTRL=y
|
||||
CONFIG_PINCTRL_AW9523=y
|
||||
# CONFIG_PINCTRL_IPQ5018 is not set
|
||||
# CONFIG_PINCTRL_IPQ5332 is not set
|
||||
# CONFIG_PINCTRL_IPQ6018 is not set
|
||||
|
|
@ -395,6 +396,7 @@ CONFIG_PM_CLK=y
|
|||
CONFIG_PM_OPP=y
|
||||
CONFIG_POSIX_CPU_TIMERS_TASK_WORK=y
|
||||
CONFIG_POWER_RESET=y
|
||||
CONFIG_POWER_RESET_GPIO=y
|
||||
# CONFIG_POWER_RESET_MSM is not set
|
||||
CONFIG_POWER_SUPPLY=y
|
||||
CONFIG_PRINTK_TIME=y
|
||||
|
|
|
|||
|
|
@ -0,0 +1,400 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "ipq8074.dtsi"
|
||||
#include "ipq8074-hk-cpu.dtsi"
|
||||
#include "ipq8074-ess.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
model = "TCL LINKHUB HH500V";
|
||||
compatible = "tcl,linkhub-hh500v", "qcom,ipq8074";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_power_blue;
|
||||
led-failsafe = &led_power_red;
|
||||
led-running = &led_power_blue;
|
||||
led-upgrade = &led_power_red;
|
||||
serial0 = &blsp1_uart5;
|
||||
serial1 = &blsp1_uart3;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
bootargs-append = " root=/dev/ubiblock0_1";
|
||||
};
|
||||
|
||||
modem {
|
||||
compatible = "gpio-export";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&modem_pins>;
|
||||
|
||||
/* output low = download mode */
|
||||
modem-edl {
|
||||
gpio-export,name = "modem_edl";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
/* output high = power on, output low = no power on after reset */
|
||||
modem-power {
|
||||
gpio-export,name = "modem_power";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&tlmm 30 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
/* output low 5s pulse = reset */
|
||||
modem-reset {
|
||||
gpio-export,name = "modem_reset";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&tlmm 29 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-poweroff {
|
||||
compatible = "gpio-poweroff";
|
||||
gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-0 = <&button_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&tlmm 47 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
gpios = <&tlmm 64 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
power {
|
||||
label = "power";
|
||||
gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_POWER>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&led_pins>;
|
||||
|
||||
4g_green {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = "4g";
|
||||
gpios = <&aw9523 0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
4g_blue {
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = "4g";
|
||||
gpios = <&aw9523 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wifi_blue {
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_WLAN;
|
||||
gpios = <&aw9523 3 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_power_blue: power_blue {
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = LED_FUNCTION_POWER;
|
||||
gpios = <&aw9523 5 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_power_red: power_red {
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_POWER;
|
||||
gpios = <&aw9523 6 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
5g_red {
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = "5g";
|
||||
gpios = <&aw9523 8 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
5g_green {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = "5g";
|
||||
gpios = <&aw9523 9 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
5g_blue {
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
function = "5g";
|
||||
gpios = <&aw9523 10 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
4g_red {
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = "4g";
|
||||
gpios = <&aw9523 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
mdio_pins: mdio-pins {
|
||||
mdc {
|
||||
pins = "gpio68";
|
||||
function = "mdc";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mdio {
|
||||
pins = "gpio69";
|
||||
function = "mdio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
button_pins: button-pins {
|
||||
bias-pull-up;
|
||||
drive-strength = <8>;
|
||||
function = "gpio";
|
||||
pins = "gpio47", "gpio62", "gpio64";
|
||||
};
|
||||
|
||||
hsuart_pins: hsuart-state {
|
||||
pins = "gpio48", "gpio49";
|
||||
};
|
||||
|
||||
modem_pins: modem-pins {
|
||||
modem_power_on {
|
||||
bias-pull-up;
|
||||
drive-strength = <8>;
|
||||
output-high;
|
||||
pins = "gpio30";
|
||||
};
|
||||
|
||||
modem_reset {
|
||||
drive-strength = <8>;
|
||||
output-high;
|
||||
pins = "gpio29";
|
||||
};
|
||||
|
||||
modem_edl {
|
||||
output-high;
|
||||
pins = "gpio46";
|
||||
};
|
||||
};
|
||||
|
||||
pcie0_default_state: pcie0_wake_gpio {
|
||||
bias-pull-up;
|
||||
drive-strength = <8>;
|
||||
function = "pcie0_wake";
|
||||
pins = "gpio59";
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_i2c2 {
|
||||
status = "okay";
|
||||
|
||||
aw9523: gpio-expander@5b {
|
||||
compatible = "awinic,aw9523-pinctrl";
|
||||
reg = <0x5b>;
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
gpio-ranges = <&aw9523 0 0 16>;
|
||||
reset-gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
led_pins: led-pins {
|
||||
pins =
|
||||
"gpio0", "gpio1", "gpio3", "gpio5", "gpio6",
|
||||
"gpio8", "gpio9", "gpio10", "gpio11";
|
||||
function = "gpio";
|
||||
input-disable;
|
||||
output-low;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_spi1 {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
reg = <0x00>;
|
||||
/* "n25q128a11" required for u-boot patching, see nand node */
|
||||
compatible = "n25q128a11", "jedec,spi-nor";
|
||||
spi-max-frequency = <50000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&blsp1_uart3 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&blsp1_uart5 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&prng {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_nand {
|
||||
status = "okay";
|
||||
/*
|
||||
* Some variants of this board use NOR+NAND configuration which is
|
||||
* currently not supported by 'qcomsmem' MTD parser while other versions
|
||||
* have NAND alone. Let U-Boot find the NAND and SPI flash dt nodes and
|
||||
* populate partitions from SMEM partition table.
|
||||
*
|
||||
* This makes it possible to support both flash configurations with a
|
||||
* single image, and also to use QCA 'runtime failsafe' and rotate
|
||||
* 'rootfs'/'rootfs_1' partitions between subsequent updates.
|
||||
*/
|
||||
compatible = "qcom,ebi2-nandc-bam-v1.5.0", "qcom,ipq8074-nand";
|
||||
|
||||
nand@0 {
|
||||
#address-cells = <0x01>;
|
||||
#size-cells = <0x01>;
|
||||
nand-bus-width = <8>;
|
||||
nand-ecc-step-size = <512>;
|
||||
nand-ecc-strength = <8>;
|
||||
reg = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
&qusb_phy_0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qusb_phy_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ssphy_0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ssphy_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdio {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
pinctrl-names = "default";
|
||||
reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
|
||||
|
||||
ethernet-phy-package@0 {
|
||||
compatible = "qcom,qca8075-package";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0>;
|
||||
|
||||
qca8075_3: ethernet-phy@3 {
|
||||
compatible = "ethernet-phy-ieee802.3-c22";
|
||||
reg = <3>;
|
||||
};
|
||||
};
|
||||
|
||||
qca8081: ethernet-phy@16 {
|
||||
compatible = "ethernet-phy-id004d.d101";
|
||||
reg = <16>;
|
||||
reset-deassert-us = <10000>;
|
||||
reset-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
&switch {
|
||||
status = "okay";
|
||||
|
||||
switch_lan_bmp = <ESS_PORT4>;
|
||||
switch_wan_bmp = <ESS_PORT6>;
|
||||
switch_mac_mode = <MAC_MODE_PSGMII>;
|
||||
switch_mac_mode2 = <MAC_MODE_SGMII_PLUS>;
|
||||
|
||||
qcom,port_phyinfo {
|
||||
port@4 {
|
||||
phy_address = <3>;
|
||||
port_id = <4>;
|
||||
};
|
||||
|
||||
port@6 {
|
||||
phy_address = <16>;
|
||||
port_id = <6>;
|
||||
port_mac_sel = "QGMAC_PORT";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&edma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&dp4 {
|
||||
status = "okay";
|
||||
phy-handle = <&qca8075_3>;
|
||||
label = "lan";
|
||||
};
|
||||
|
||||
&dp6_syn {
|
||||
status = "okay";
|
||||
phy-handle = <&qca8081>;
|
||||
label = "wan";
|
||||
};
|
||||
|
||||
&pcie_qmp0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
pinctrl-0 = <&pcie0_default_state>;
|
||||
pinctrl-names = "default";
|
||||
perst-gpio = <&tlmm 58 GPIO_ACTIVE_LOW>;
|
||||
|
||||
pcie@0 {
|
||||
modem@0,0 {
|
||||
reg = <0x00 0x00 0x00 0x00 0x00>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&wifi {
|
||||
status = "okay";
|
||||
|
||||
qcom,ath11k-calibration-variant = "TCL-LINKHUB-HH500V";
|
||||
};
|
||||
|
|
@ -405,6 +405,21 @@ define Device/spectrum_sax1v1k
|
|||
endef
|
||||
TARGET_DEVICES += spectrum_sax1v1k
|
||||
|
||||
define Device/tcl_linkhub-hh500v
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := TCL
|
||||
DEVICE_MODEL := LINKHUB HH500V
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
DEVICE_DTS_CONFIG := config@hk09
|
||||
SOC := ipq8072
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-ubi | qsdk-ipq-factory-nand
|
||||
DEVICE_PACKAGES := ipq-wifi-tcl_linkhub-hh500v kmod-mhi-pci-generic \
|
||||
kmod-mhi-wwan-ctrl kmod-mhi-wwan-mbim
|
||||
endef
|
||||
TARGET_DEVICES += tcl_linkhub-hh500v
|
||||
|
||||
define Device/tplink_deco-x80-5g
|
||||
$(call Device/FitImage)
|
||||
|
|
|
|||
|
|
@ -42,6 +42,9 @@ netgear,wax630)
|
|||
redmi,ax6)
|
||||
ucidef_set_led_netdev "wan" "WAN" "blue:network" "wan"
|
||||
;;
|
||||
tcl,linkhub-hh500v)
|
||||
ucidef_set_led_wlan "wlan5g" "WiFi 5GHz" "blue:wlan" "phy0radio"
|
||||
;;
|
||||
xiaomi,ax3600)
|
||||
ucidef_set_led_netdev "wan-port-link" "WAN-PORT-LINK" "90000.mdio-1:01:green:wan" "wan" "tx rx link_10 link_100 link_1000"
|
||||
ucidef_set_led_netdev "lan1-port-link" "LAN1-PORT-LINK" "90000.mdio-1:02:green:lan" "lan1" "tx rx link_10 link_100 link_1000"
|
||||
|
|
|
|||
|
|
@ -13,6 +13,7 @@ ipq807x_setup_interfaces()
|
|||
case "$board" in
|
||||
aliyun,ap8220|\
|
||||
edgecore,eap102|\
|
||||
tcl,linkhub-hh500v|\
|
||||
tplink,deco-x80-5g|\
|
||||
yuncore,ax880|\
|
||||
zte,mf269)
|
||||
|
|
@ -93,6 +94,10 @@ ipq807x_setup_macs()
|
|||
lan_mac=$(macaddr_add "$wan_mac" 1)
|
||||
label_mac="$wan_mac"
|
||||
;;
|
||||
tcl,linkhub-hh500v)
|
||||
wan_mac=$(mtd_get_mac_binary "0:ART" 0x5e290)
|
||||
lan_mac=$(mtd_get_mac_binary "0:ART" 0x5e296)
|
||||
;;
|
||||
tplink,deco-x80-5g)
|
||||
label_mac=$(get_mac_binary /tmp/factory_data/default-mac 0)
|
||||
lan_mac=$(macaddr_add $label_mac 1)
|
||||
|
|
|
|||
|
|
@ -96,6 +96,12 @@ case "$FIRMWARE" in
|
|||
spectrum,sax1v1k)
|
||||
caldata_extract_mmc "0:ART" 0x1000 0x20000
|
||||
;;
|
||||
tcl,linkhub-hh500v)
|
||||
caldata_extract "0:ART" 0x1000 0x20000
|
||||
ath11k_patch_mac $(mtd_get_mac_binary "0:ART" 0x5e29c) 0
|
||||
ath11k_patch_mac $(mtd_get_mac_binary "0:ART" 0x5e2a2) 1
|
||||
ath11k_set_macflag
|
||||
;;
|
||||
tplink,deco-x80-5g)
|
||||
caldata_extract "0:art" 0x1000 0x20000
|
||||
label_mac=$(get_mac_binary /tmp/factory_data/default-mac 0)
|
||||
|
|
|
|||
22
target/linux/qualcommax/ipq807x/base-files/etc/init.d/modem
Executable file
22
target/linux/qualcommax/ipq807x/base-files/etc/init.d/modem
Executable file
|
|
@ -0,0 +1,22 @@
|
|||
#!/bin/sh /etc/rc.common
|
||||
|
||||
START=15
|
||||
|
||||
boot() {
|
||||
case $(board_name) in
|
||||
tcl,linkhub-hh500v)
|
||||
PCIPATH="/sys/bus/pci/devices/0000:01:00.0"
|
||||
|
||||
for i in $(seq 0 10); do
|
||||
[ -d "${PCIPATH}" ] && break
|
||||
echo 1 > /sys/bus/pci/rescan
|
||||
sleep 2
|
||||
done
|
||||
|
||||
if [ ! -d "${PCIPATH}" ]; then
|
||||
echo "No modem PCIe device found"
|
||||
exit 1
|
||||
fi
|
||||
;;
|
||||
esac
|
||||
}
|
||||
|
|
@ -263,6 +263,10 @@ platform_do_upgrade() {
|
|||
CI_DATAPART="rootfs_data"
|
||||
emmc_do_upgrade "$1"
|
||||
;;
|
||||
tcl,linkhub-hh500v)
|
||||
tcl_upgrade_prepare
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
tplink,deco-x80-5g|\
|
||||
tplink,eap620hd-v1|\
|
||||
tplink,eap660hd-v1)
|
||||
|
|
|
|||
|
|
@ -0,0 +1,91 @@
|
|||
# based on target/linux/qualcommax/ipq50xx/base-files/lib/upgrade/elecom.sh
|
||||
|
||||
. /lib/functions.sh
|
||||
|
||||
# Read or update an entry in Qualcomm bootconfig partition
|
||||
#
|
||||
# parameters:
|
||||
# $1: partition name of bootconfig (ex.: "0:bootconfig", "0:bootconfig1", etc)
|
||||
# $2: entry name in bootconfig (ex.: "0:hlos", "rootfs", etc)
|
||||
# $3: index to set for the entry (0/1)
|
||||
#
|
||||
# operations:
|
||||
# read : bootconfig_rw_index <bootconfig> <entry>
|
||||
# write: bootconfig_rw_index <bootconfig> <entry> <index>
|
||||
bootconfig_rw_index() {
|
||||
local bootcfg="$1"
|
||||
local partname="$2"
|
||||
local index="$3"
|
||||
local mtdidx
|
||||
local tempfile
|
||||
local current
|
||||
|
||||
if [ -z "$bootcfg" ] || [ -z "$partname" ]; then
|
||||
echo "no value specified for bootconfig or partition entry"
|
||||
return 1
|
||||
fi
|
||||
|
||||
case "$index" in
|
||||
0|1|"") ;;
|
||||
*) echo "invalid bootconfig index specified \"$index\""; return 1 ;;
|
||||
esac
|
||||
|
||||
mtdidx=$(find_mtd_index "$bootcfg")
|
||||
[ ! "$mtdidx" ] && {
|
||||
echo "cannot find mtd index for $partname"
|
||||
return 1
|
||||
}
|
||||
|
||||
tempfile=/tmp/mtd"$mtdidx".bin
|
||||
dd if=/dev/mtd"$mtdidx" of="$tempfile" bs=1 count=336
|
||||
[ $? -ne 0 ] || [ ! -f "$tempfile" ] && {
|
||||
echo "failed to create a temp copy of /dev/mtd$mtdidx"
|
||||
return 1
|
||||
}
|
||||
|
||||
current=$(get_bootconfig_primaryboot "$tempfile" "$partname")
|
||||
|
||||
if [ -z "$index" ]; then
|
||||
echo "$current"
|
||||
elif [ "$current" != "$index" ]; then
|
||||
set_bootconfig_primaryboot "$tempfile" "$partname" "$index"
|
||||
mtd write "$tempfile" /dev/mtd"$mtdidx" 2>/dev/null
|
||||
[ $? -ne 0 ] && {
|
||||
echo "failed to write temp copy back to /dev/mtd$mtdidx"
|
||||
return 1
|
||||
}
|
||||
fi
|
||||
|
||||
rm "$tempfile"
|
||||
}
|
||||
|
||||
tcl_swap_active_root() {
|
||||
local index
|
||||
|
||||
index=$(bootconfig_rw_index "0:BOOTCONFIG" rootfs)
|
||||
if [ -z "$index" ]; then
|
||||
v "failed to read bootconfig index..."
|
||||
nand_do_upgrade_failed
|
||||
fi
|
||||
|
||||
if [ "$index" = "1" ]; then
|
||||
bootconfig_rw_index "0:BOOTCONFIG" rootfs 0
|
||||
bootconfig_rw_index "0:BOOTCONFIG1" rootfs 0
|
||||
else
|
||||
bootconfig_rw_index "0:BOOTCONFIG" rootfs 1
|
||||
bootconfig_rw_index "0:BOOTCONFIG1" rootfs 1
|
||||
fi
|
||||
}
|
||||
|
||||
tcl_upgrade_prepare() {
|
||||
local delay
|
||||
|
||||
delay=$(fw_printenv -n bootdelay)
|
||||
[ -z "$delay" ] || [ "$delay" -eq "0" ] && \
|
||||
fw_setenv bootdelay 3
|
||||
|
||||
if [ -z "$UPGRADE_OPT_USE_CURR_PART" ]; then
|
||||
tcl_swap_active_root
|
||||
CI_UBIPART="rootfs_1"
|
||||
fi
|
||||
}
|
||||
Loading…
Add table
Reference in a new issue