forked from mirror/openwrt
mediatek: filogic: add Keenetic Sprinter (KN-3711) support
Specification:
SoC: Mediatek MT7981BA
RAM: 512 MB DDR4 RAM
Flash: Winbond W25N01GV 128 MB SPI-NAND (dual boot on OEM)
WiFi: MT7976CN DBDC AX
Switch: MediaTek MT7531AE (3x LAN Gigabit ports) + Internal Gbe Phy (1x WAN Gigabit port)
GPIO: 4x LED (power, internet, fn, wifi), 2x buttons (wps, reset), 1x switch (mesh)
UART Interface:
Pins: VCC, TX, RX, NC, GND
Settings: 115200, 8N1
Flashing via TFTP:
1. Connect your PC and router to the first LAN port, configure PC interface using IP 192.168.1.2, mask 255.255.255.0
2. Save the factory image of the OpenWRT firmware, renamed to KN-3711_recovery.bin, on the TFTP server
3. Hold the reset button and power up the device
4. Keep the button pressed until the status LED starts blinking
Signed-off-by: Vladimir Epifantsev <volatilefield@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19633
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit is contained in:
Vladimir Epifantsev
Hauke Mehrtens
parent
c43925313e
commit
9241f29c0e
4 changed files with 351 additions and 0 deletions
329
target/linux/mediatek/dts/mt7981b-keenetic-kn-3711.dts
Executable file
329
target/linux/mediatek/dts/mt7981b-keenetic-kn-3711.dts
Executable file
|
|
@ -0,0 +1,329 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-only OR MIT
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "mt7981b.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Keenetic KN-3711";
|
||||
compatible = "keenetic,kn-3711", "mediatek,mt7981";
|
||||
|
||||
aliases {
|
||||
label-mac-device = &gmac0;
|
||||
led-boot = &power_led;
|
||||
led-failsafe = &power_led;
|
||||
led-running = &power_led;
|
||||
led-upgrade = &power_led;
|
||||
serial0 = &uart0;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
switch-fn {
|
||||
label = "fn";
|
||||
gpios = <&pio 0 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_0>;
|
||||
linux,input-type = <EV_SW>;
|
||||
};
|
||||
|
||||
button-reset {
|
||||
label = "reset";
|
||||
gpios = <&pio 24 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
button-wps {
|
||||
label = "wps";
|
||||
gpios = <&pio 29 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
power_led: led-0 {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_POWER;
|
||||
gpios = <&pio 11 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
led-1 {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WAN;
|
||||
gpios = <&pio 12 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-2 {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = "fn";
|
||||
gpios = <&pio 9 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-3 {
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WLAN_2GHZ;
|
||||
gpios = <&pio 34 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
};
|
||||
|
||||
virtual_flash {
|
||||
compatible = "mtd-concat";
|
||||
devices = <&firmware1 &firmware2>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "kernel";
|
||||
reg = <0x0 0x600000>;
|
||||
};
|
||||
|
||||
partition@600000 {
|
||||
label = "ubi";
|
||||
reg = <0x600000 0x06000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
ð {
|
||||
status = "okay";
|
||||
|
||||
gmac0: mac@0 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&macaddr_factory_4>;
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
|
||||
mac@1 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <1>;
|
||||
phy-mode = "gmii";
|
||||
phy-handle = <&int_gbe_phy>;
|
||||
label = "wan";
|
||||
|
||||
nvmem-cell-names = "mac-address";
|
||||
nvmem-cells = <&macaddr_factory_a>;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio_bus {
|
||||
switch@1f {
|
||||
compatible = "mediatek,mt7531";
|
||||
reg = <0x1f>;
|
||||
reset-gpios = <&pio 22 GPIO_ACTIVE_HIGH>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-parent = <&pio>;
|
||||
interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
label = "lan3";
|
||||
};
|
||||
|
||||
port@6 {
|
||||
reg = <6>;
|
||||
label = "cpu";
|
||||
ethernet = <&gmac0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pio {
|
||||
spi0_flash_pins: spi0-pins {
|
||||
mux {
|
||||
function = "spi";
|
||||
groups = "spi0", "spi0_wp_hold";
|
||||
};
|
||||
|
||||
conf-pu {
|
||||
pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
|
||||
drive-strength = <MTK_DRIVE_8mA>;
|
||||
bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
|
||||
};
|
||||
|
||||
conf-pd {
|
||||
pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
|
||||
drive-strength = <MTK_DRIVE_8mA>;
|
||||
bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi0_flash_pins>;
|
||||
status = "okay";
|
||||
|
||||
/* Winbond W25N01GV SPI NAND (128 MiB) */
|
||||
spi_nand@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "spi-nand";
|
||||
reg = <0>;
|
||||
|
||||
spi-max-frequency = <52000000>;
|
||||
spi-tx-buswidth = <4>;
|
||||
spi-rx-buswidth = <4>;
|
||||
|
||||
spi-cal-enable;
|
||||
spi-cal-mode = "read-data";
|
||||
spi-cal-datalen = <7>;
|
||||
spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4e 0x41 0x4e 0x44>;
|
||||
spi-cal-addrlen = <5>;
|
||||
spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
|
||||
|
||||
mediatek,nmbm;
|
||||
mediatek,bmt-max-ratio = <1>;
|
||||
mediatek,bmt-max-reserved-blocks = <64>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
/* bl2 */
|
||||
partition@0 {
|
||||
label = "preloader";
|
||||
reg = <0x0 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
/* fip */
|
||||
partition@80000 {
|
||||
label = "u-boot";
|
||||
reg = <0x80000 0x200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@280000 {
|
||||
label = "u-config";
|
||||
reg = <0x280000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@300000 {
|
||||
label = "rf-eeprom";
|
||||
reg = <0x300000 0x200000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
eeprom_factory_0: eeprom@0 {
|
||||
reg = <0x0 0x1000>;
|
||||
};
|
||||
|
||||
/* lan mac */
|
||||
macaddr_factory_4: macaddr@4 {
|
||||
reg = <0x4 0x6>;
|
||||
};
|
||||
|
||||
/* wan mac */
|
||||
macaddr_factory_a: macaddr@a {
|
||||
reg = <0xa 0x6>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
firmware1: partition@500000 {
|
||||
label = "firmware_1";
|
||||
reg = <0x500000 0x3500000>;
|
||||
};
|
||||
|
||||
partition@3a00000 {
|
||||
label = "config_1";
|
||||
reg = <0x3a00000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3a80000 {
|
||||
label = "dump";
|
||||
reg = <0x3a80000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3c00000 {
|
||||
label = "u-state";
|
||||
reg = <0x3c00000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3e80000 {
|
||||
label = "u-config_res";
|
||||
reg = <0x3e80000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@3f00000 {
|
||||
label = "rf-eeprom_res";
|
||||
reg = <0x3f00000 0x200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
firmware2: partition@4100000 {
|
||||
label = "firmware_2";
|
||||
reg = <0x4100000 0x3500000>;
|
||||
};
|
||||
|
||||
partition@7600000 {
|
||||
label = "config_2";
|
||||
reg = <0x7600000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&wifi {
|
||||
nvmem-cell-names = "eeprom";
|
||||
nvmem-cells = <&eeprom_factory_0>;
|
||||
status = "okay";
|
||||
};
|
||||
|
|
@ -46,6 +46,7 @@ mediatek_setup_interfaces()
|
|||
creatlentem,clt-r30b1-112m|\
|
||||
cudy,wr3000-v1|\
|
||||
jcg,q30-pro|\
|
||||
keenetic,kn-3711|\
|
||||
keenetic,kn-3811|\
|
||||
qihoo,360t7|\
|
||||
routerich,ax3000|\
|
||||
|
|
|
|||
|
|
@ -141,6 +141,7 @@ case "$board" in
|
|||
jdcloud,re-cp-03)
|
||||
[ "$PHYNBR" = "1" ] && mmc_get_mac_binary factory 0xa > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
keenetic,kn-3711|\
|
||||
keenetic,kn-3811|\
|
||||
keenetic,kn-3911)
|
||||
[ "$PHYNBR" = "1" ] && \
|
||||
|
|
|
|||
|
|
@ -1362,6 +1362,26 @@ define Device/jdcloud_re-cp-03
|
|||
endef
|
||||
TARGET_DEVICES += jdcloud_re-cp-03
|
||||
|
||||
define Device/keenetic_kn-3711
|
||||
DEVICE_VENDOR := Keenetic
|
||||
DEVICE_MODEL := KN-3711
|
||||
DEVICE_DTS := mt7981b-keenetic-kn-3711
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware
|
||||
UBINIZE_OPTS := -E 5
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
KERNEL_SIZE := 6144k
|
||||
IMAGE_SIZE := 108544k
|
||||
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | \
|
||||
append-squashfs4-fakeroot
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | \
|
||||
append-ubi | check-size | zyimage -d 0x803711 -v "KN-3711"
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += keenetic_kn-3711
|
||||
|
||||
define Device/keenetic_kn-3811
|
||||
DEVICE_VENDOR := Keenetic
|
||||
DEVICE_MODEL := KN-3811
|
||||
|
|
|
|||
Loading…
Add table
Reference in a new issue